Having problems with your Bosch 24 in. SHU43 Built-in Dishwasher ?

On my bosch shu66 diswasher the error code indicates a number 1, aqua sensor I think. There is a screw missing in the soap dispensor and it's been letting water into the door interior. could this be repaired by replacement of the screw and drying out the interior insulation and wiring


Answers :

As long as it is sealed and you should also make sure there is not water in the white plastic pan under the dishwasher..
Repair Help & Product Troubleshooting for Bosch 24 in. SHU43 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

On my bosch shu66 diswasher the error code indicates a number 1, aqua sensor I think. There is a screw missing in the soap dispensor and it's been letting water into the door interior. could this be repaired by replacement of the screw and drying out the interior insulation and wiring The solution I tried didn't clear the error code on the panel. Is there a reset or do I need to replace the aqua sensor or ? The machine still won't start and displays a #1 on display. There is no water in the whi


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

On my bosch shu66 diswasher the error code indicates a number 1, aqua sensor I think. There is a screw missing in the soap dispensor and it's been letting water into the door interior. could this be repaired by replacement of the screw and drying out the interior insulation and wiring


As long as it is sealed and you should also make sure there is not water in the white plastic pan under the dishwasher.. ... Bosch 24 in. SHU43 Built-in Dishwasher

Leaking This is a problem that I have when the dishwasher is in drying mode. I will find a 5X5 and sometimes smaller, size water spot under the dishwasher after the dishwasher has stopped. I was told it was the vent were the steam comes out and I had that replaced. It still leaks, then they told me to replace the rubber around the door, still leaks now they order a whole new plastic interior door. Please if you have any ideas what could be causing the problem, please let me know. Thank you


\015\012open the bottom panel 2-4 screw\015\012take a flashlight and turn the machine on\015\012see where it come from\015\012if you need take the unit out a bit f ... Jenn-Air JDB4000AWS Stainless Steel Dishwasher

Water will not drain out. do not have a drain airGap. when opened dishwasher this afternoon still had water in the bottom of it. Emptied the dishes, closed the door, pushed cancel/drain. the green light came on and i could hear the dishwasher running but not hear the water draining out. Let it run the 2 minute cycle for cancel/drain opened the door and the water is still there.


Hi,Here is a tip that I wrote that will help you with your dishwasher not drainingproblem...Dishwasher Problems - Waterwill not drain out ... KitchenAid 24 in. KUDM01TJ - Multiple Color Built-in Dishwasher

I have a Bosch SHU66C02. I opened the door to stop it from running temporarily, while it was sitting not running, it leaked all of the water out of the bottom right corner of the door, and when I went to start it later it just hummed but the timer didn't go down for over an hour. I tried to put more water in but as soon as I started I could hear the water added to drain. I turned the breaker in the fuze box off to it and let it sit for over an hour, but when I restarted, the timer was still at


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

My maytag quiet series fills with water and then starts for 5 seconds then stops. This happens 4 times and then the entire system just stops. To help troubleshoot I used a screw driver to trigger the closed door so that I could leave the door open when the cycle starts and the pumps seems to be working and water sprays all over the place. I also took apart the impellar blade to make sure there was nothing jammed and everything is clean. Maytag MDB7500AWW


... Maytag 24 in. MDB7600A Jetclean® II Built-in Dishwasher

I have a Whirlpool which just recently started leaking from the door occasionally and it is most unpredictable. It eventually stops, but before it does it will deposit about a pint of water. I have replaced the float and the float switch, thinking those were the cheapest parts and perhaps the switch was faulty and letting too much water in. That did not work. When this happens I checked the exhaust and hot steam is coming out. Could it be the water inlet valve? If the seal was bad I am ass


Hi\015\012\015\012The issue is with the water inlet valve that is bad and\015\012should be replaced. I believe everything else is working fine. Hope this\015\012helps...please post back for further assistance.\015\012\015\012Dani ... Dishwashers

WP DW Mod # GU1200XTLS0: this unit filled with water and just stopped running. I have power to the unit. The control panel does not light up at all. Its wierd that I have power to the board and all the wires seem to have power! No burnt spots and no burnt smell on the board.Hmmm! Door latch and switches all check ok. Oddly it seems like the line power to DW goes all the way thru the unit and back through the nutural wire. Could the motor windings be burnt out?


Hello , there should be a fuse located by or on the side of the board with 2 wires going to it , one from the latch and one from the board ,it does come off , use an ohm meter to check it , it should ohm out or have low resistance make sure to take t ... Whirlpool GU1200XTLS Stainless Steel Dishwasher

I have a diplomat adp8332 integrated dishwasher showing an F3 fault code.I dismantled the door casing and found that the wiring sheath had split and cut through 2 wires.I have repaired the wires and fitted a new sheath,the F3fault code still appears(no heated water and only rinse cycle)Could the PCB have part blown or the heating element?


... Dishwashers

I have a kenmore quiet guard standard dishwasher. About 2 weeks ago it started leaking. today I pulled it out and found that looking straight ahead at the door on the lefthand side under the bottom is 2 small wire metal fittings that screw up into the bottom of the dishwasher. one was loose and dripping water. when i screwed it back in i noticed that it was stripped out. can it be replaced or should I scilicone around it to stop it?


... Dishwashers

Door leak The dishwasher is 2 and half year old and is randomly leaking for at least one year or even more. The leak originally occurred at both lower ends of the door, close to the hinges. The leak was about one liter and the door panel sound insulation soaked with water. After door panel was removed, the leak location was identified at both ends of the lower door gasket. The outside part of the U-shaped gasket was filled with water, and eventually water was spilled on the floor. The leak can g


I had the same problem. On the right side of the tank in Bosch dishwashers there is a steam port. If you place a large object in the right hand edge of the tray, a pressure build up causes the leak. Put large stuff on the left and you should be good ... Bosch 24 in. SHU5305UC Built-in Dishwasher

Door leak I have a small leak between the bottom of the dishwasher door the lower service panel on the dishwashere. I did replace the seal on the inside bottom of the door along with the other parts that come with the door seal. Could there be a gasket leak around the detergent dispenser or the vent at the top of the inside of the door. I did not check the water lever as was mentioned in a previous question on water level, but the float does move up and down quite freely. Any suggestions as to w


I had my dishwasher leaking alot at the bottom of the doo,r and found out that the steam vent was very cloged with gunk. After taking the vent cover off on the inside of the door and cleaning, then putting the vent cover back on NO MORE leaking. Th ... KitchenAid 24 in. KUDS25 Built-in Dishwasher

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of water is let in when the pump turns on and the washing cycle begins. Opening the door shows that the water level does not reach the bottom of the float. When I close the door, the wash cycle begins again but stops after a few seconds. This is when the water begins to fill again. This time, the wat


Larry,The float is generally for overflow conditions and will interrupt power to the fill valve solenoid. If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water ... Whirlpool GU2400XTP Built-in Dishwasher

I bought this dishwasher 5 years ago and was kept in the box until last month. I installed it, turned on the water and no water is being pumped into the unit from the water release valve in the dishwasher. I then checked all the cycles and everything works except for the pump. Then I checked to see if any power/volts was going to the pump and there is none. Could it be a wiring problem or could it be the circuit board?? please help. thanks


You will have to check all the connections visually. Since you know how to use a meter, see where the current stops. See if there is current coming from the control board to the pump. the water inlet solenoid valve should "free flow" water into the m ... GE 24 in. Profile PDW7800 Built-in Dishwasher

My Bosch SHY56A02 dishwasher won't fill....When cycle is started, it seems to pump water out but none in. Water feed is good....Added water manually and it pumps out immediately. Also, unit continues to run with door open...door switch is not jumpered. Could it be the fill valve? More likely the control module? Thanks for your help!


Hi,\015\012\015\012As water is filling in your dishwasher a float rises along with it. When the float reaches a predetermined level it shuts off the flow of water by activating a switch thereby preventing a leak. Sometimes the float can g ... Bosch Dishwashers

I purchased a new dishwasher on 2/22/07 at the Home Depot in Parksburg,Pa. I first had to have it repaired on 4/28/08 for wires stuck to inner door. They repaired two broken wires and added insulation so wires do not stick to the door. The second repair was a little more than two months later. On 7/18/08 they had to install a new motor because the motor locked up. Both times I waited several weeks due to not having money and appliance center being busy. I used J.B Zimmerman in Blue Ball,P


Hel1Dav2,\015\012\015\012I understand your frustration with having to deal with major repairs to a new applaince. However, I don't belive this is the correct forum that you need to use. I have found a helpful link that you may try in th ... Dishwashers

Kude48fxbl - brand new out-of-the-box. When put through a test cycle after installing it, water poured out of the bottom left edge of the door. This was not associated with either the water input or the discharge hose, but rather seemed to come from the interior of the washer and out under the door. The door seemed well latched, and running it with some dishes in the bottom tray (not blocking the soap dispenser) didn't help.


... KitchenAid Dishwashers

Water leaks from bottom of door,it does not do it all the time and only small amounts. i can feel feel that the insulation is wet. can i take off the door panel and replace the insulation? the model no. is dwu9200ab and is 17 years old.


... Maytag 24 in. DWU9202 Built-in Dishwasher

Dishwasher model: se6 tie1 Fitted under kitchen work-top. Problem: After setting a program & switching on & closing door ? there is a normal sound from within but if door is opened there is no evidence of water being pumped in. I previously cleared food debris from the drainage pump area (including under the pump cover), checked the spray arms and checked the water supply was getting as far as the long in-take pipe. As it seems problematic to remove the (screwed in) dishwasher, I have not che


... Dishwashers

We recently installed a Kenmore dishwasher, Mfr Model# 13943. We have used the dishwasher approximately six times since Thanksgiving. Each time, after the wash cycle is complete, when we open the door, water has collected on the interior of the door, and water remains standing on some of the washed dishes. Is this normal?


... Kenmore Dishwashers

I wired my Bosch Dishwasher wrong and did a quick wash with it. Later on it stopped working and I figured out I had wired it wrong. I then disconnected it and rewired it. It buzzes for a bit then swishes some water around inside then buzzes again. When I open the door after it says clean it has murky water in the bottom like it was mixed with soap but never emptied. What did I do?


I hope this is not a quiz. Can you please clarify what component did you wire incorrectly inside the dishwasher? Did the dishwasher have a fault that you were trying to rectify.\015\012\015\012it will also help if you provide the full mod ... Dishwashers

My SGS55M72AU/65 does not get rid of its drain water, although that wee pump in the bottom is clearly working (which I could see after removing filters and pump cover). There is no blockage near the drain pipe connection, so I infer there is a blockage somewhere inside the dishwasher, in a place I can't get to without further instruction. I've removed most of the drain water and pulled the unit out, so I could lay it on its side and start taking screws out. But I much prefer to have some guidanc


Ok i am attempting to help you although i dont see your make of dishwasher but im using what i know without manual. to ensure there is a blockage in the dishwasher remove that hose you checked at garbage disposal or vent and leave it disconnected an ... Dishwashers

I cant get me dishwasher to start i have tested the overflow switch and its fine i have also tested the water inlet valve and its is fine. but it will not fill the dishwasher with water i have even removed the hose to see if there was any blockage in the line come out from the what inlet valve. the button light up on dishwasher and the cycles work a long with the start button, i have left the door open to see if the door senor could possibly bee an issue and it tested good and function correctly


Hi.If there is no voltage to valve, then parts that can be responsible are only and all the following:Overfill switch or overfill device.Door switch.Electronic control Wiring.If the overfill switc ... Dishwashers

Bosch Dishwasher I have a stainless steel Bosch dishwasher, I made the "mistake" to try to see if I could fix the jammed handle from the door. Unfortunately, (did not realize the top panel comes off without opening the entire door). I removed the screws from the door frame (Inside panel), and the door springs/latched got loose. I would like to put it back together, but I dont have any diagrams on the door to make sure all parts are in place to put the door back together. I have been havin


Hi ED,\015\012\015\012It sounds like a real problem here. If the springs are still in one piece, my best guess is to to remove the springs from the door. Then attach the springs to the dishwasher body first, then reattach the spring to the door. Not ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

Westinghouse Virtuoso 922 dishwasher. Wash cycle completes, but water does not drain out. If I let the cycle continue, after a delay the rinse cycle starts, but of course no clean water is pumped in so the dishes are "rinsed" in the dirty wash water. The wash cycle itself is successful with water pumping all around the washer if I open the door mid-cycle. I have removed and cleaned all filters which were correctly fitted so I am confident there is no foreign matter inside pump. When the water sh


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1739 seconds