Having problems with your Bosch 24 in. SHU43 Built-in Dishwasher ?

My Bosch dishwasher is off but water continues to over fill base.I'm not using the sink. I've sucked the water out with a wet dry vac three times in the last 2 hours. I've also sucked the water out of the pan underneath the washer. The water is coming from the ''side hole'' not the drain hole.


Answers :

You will need to turn the water supply off at the wall as the fill valve has got some dirt in it and cannot close properly
\015\012
\015\012To clean it out is a strip down job so unless you are mechanically minde then it is down to a repair person being called out
Repair Help & Product Troubleshooting for Bosch 24 in. SHU43 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Bosch dishwasher is off but water continues to over fill base.I'm not using the sink. I've sucked the water out with a wet dry vac three times in the last 2 hours. I've also sucked the water out of the pan underneath the washer. The water is coming from the ''side hole'' not the drain hole.


You will need to turn the water supply off at the wall as the fill valve has got some dirt in it and cannot close properly\015\012\015\012To clean it out is a strip down job so unless you are mechanically minde then it is down to a repair ... Bosch 24 in. SHU43 Built-in Dishwasher

I have a Frigidaire UC DW Model FDB250RHB2 The unit is not a year old. It is not getting dishes very clean. I read similar posts. I found that there is water coming from top nozzle but not a very impressive stream. It is weak enough that most of the water misses the funnel on top rack. Also not top or bottom arms spin. Last week when i would quick peek during wash cycle there seem to be water coming out of top arm's holes but no spin. We also are getting heavy white staining on glass ware


... Frigidaire FDB520RH Builtin Dishwasher

I purchased my KARCHER G2500VH last summer. I used it one time for about an hour. I tried to start it today, seems like its not getting gas. I checked the gasline to make sure gas was flowing. I removed the sparkplug, poured a little gas into the engine through the plug hole. Replaced the plug, pulled the rope and it started for about two seconds. I also poured fresh gas in tank. Cannot get to start.


Have tried to start our BlackMax 2700psi pressure washer, it is not getting gas to the carburetor, what to do? ... Pressure Washers

I have the two drawer dishwasher. It's about 10 years old. The top drawer continues to work OK but for the last three attempts when I run the bottom drawer water gets out into the drip pan below and gives the F1 signal. I can dry the drip pan out and clear the F1 signal so the top drawer works. But running the bottom drawer causes water to leak again with the resultant F1 signal. There is very little water in the bottom drawer (just a little in the filter bowl) so I think the pump is pumping


Hi,Unless you keep using the wrong detergent or keep putting dishes that \015\012are to tall in there. i would have to say your actuators ar bad and its \015\012not letting the lid go down to seal it all the time.There is no adjustment. Y ... Fisher and Paykel Dishwashers

Dishwasher (Model # SHU6806UC), unit is about 8 years old, very light use, less than once a month, and no previous problems. Turned on unit and after about 10 minutes, I found water on floor coming from dishwasher. Turned unit off and turned off water shut-off valve. Removed dishwasher from cabinet. Found mice had chewed a hole in water discharge hose under unit, inspected all hoses, and found another hole chewed in the 13" flex hose in the front of the unit. Also found the float chewed to alm


Hi,\015\012 Check the valve is open where the supply gets its water from the sink supply.There is a garden hose type swivel adapter after the valve, Close the valve tightly and then unscrew that hose coupling and see if the hose is full of w ... Bosch 24 in. SHU6802UC / SHU6806UC Built-in Dishwasher

Stopped working the pressure washer i have been usingfor the last hour has stopped working water is going into the unit and when switched on the unit apeares to be running however allthough water is comming out of the hose it is not under pressue have tried leavin it for half hour to cool downn but no good


... Pressure Washers

Hi, we have a Neff dishwasher and noticed a couple of days ago that it took hours longer than usual for the dishwasher to complete its cycle. Last night after the machine had been on for about 4 hours we checked and although there was some water at the bottom of the machine it had not started to wash the dishes although we had heard noises coming from the machine. On opening the integrated door notice that the "check water supply" indicator was lit up. Do you have any suggestions as to what


... Neff 24 in. S5443X2 Built-in Dishwasher

I have a candy trio 501 dishwasher with intergrated oven. When I put a cycle on it starts its first rinse then after 5/10 mins stops and beeps constantly. It's still full of water too. When I put it on rinse cycle it compleates the cycle so inlet and drainage should be ok. Ive removed drain pipe and made sure its not kinked and also clear. I've removed and drained the compartments that had water in and also blew down the pips to see if clear all ok. I've checked the heater element with meter and


... Dishwashers

Hi, I have a Kenmore 15879 that is basically working except the bottom water spinner...lol (don't know technical name). The dishwasher pumps the water into the bottom of the dishwasher, will heat the water, but not disperse the water in the spinning sprinkler manner it's suposed to. I've opened the dishwasher in time to see that water is spurting out of the holes about 2" high, but it's just not spinning. The water also drains just fine after the whole cycle.


This is caused by the impeller being clogged or the pump is failing, When the pump is woring properly the water will shoot out with force. ... Kenmore 15879 Built-in Dishwasher

Our Kemore dishwasher is leaking water onto floor, and the water valve continues to pour water when machine was turned off, but is not leaking water now. There is also standing water at bottom of tub from running machine last night. Can I test to see if it is fill valve or the overfill float? Are these easily replaced?


You just need to clean the pump area in the bottom of your unit :)try to take spray arm out if you can and then open pump cover clean it good but watch for broken glass in it ...and thats it :) ... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

I also have a dishwasher (AEG Favorit), and it does not heat the water anymore. It worked fine for last 3 years, and all sudden, it only washes dishes with cold water. Could you please help to solve this problem? The hot water line is fine and I do have the hot water to the sink next to the dishwasher. Thank you in advance for your help.


... AEG 23 in. Favorit 44070IW Built-in Dishwasher

We are having a problem with our LG Dishwasher. The machine is washing for about half an hour and then will stop and report an E1 error. According to the user manual this means "Water leakage in Hose connection" or "Water is leaked by damages". We have checked the diswasher's water connections and can't see any water leaking out. We have also cleaned the filers and checked the spray arms but that has not made any diffrence. Any suggestions what this error means and what we can try to resolve it


... Whirlpool 24 in. DU940QWD Built-in Dishwasher

My GE Nautilus DW doesn't fully drain. When it is drained as much as it will it leaves water in the sump at the rear right. If you run the pump at that point, it sucks water out of the sump, but when you open the door and the pump stops water flows back into it. It seems like there is a check valve that isn't working. I have cleaned the sump and the screen which runs accross the rear. I also have taken the plunger out and cleaned it. Then I took the housing for the plugner off the bottom. I don'


HI. check the following areas for fualts.1. Air gap / Drain hosesIf there is an air gap (located in the sink, near the faucet), check to see if it is clogged. Unscrew the top cap and see if there is anything blocking inside. Note: I ... Dishwashers

I have a Sears (Briggs) 2550 washer mod # 580.752190, has been working great but when I got it out last week it wouldn't start with the water on, I turn the water off bleed the pressure out the wand and it started and ran great, I thought it might be the relief valve, I removed the valve turned on the water, a big stream was shooting out the hole where the valve goes, I started the engine and it ran but sounded like it was about half loaded. where do I go from here ? Thanks.


... Briggs Stratton 020273 Elite Series Portable Gas Pressure Washer

Low Pressure It runs, and sprays water, but doesn't have near the pressure it had. Its also losing water out a weep hole on the water pump. Manual says check the screens, but I took it apart and didn't find any. Any suggestions?


Sounds like you may need new pump seals. ... Campbell Hausfeld PW2575 Pressure Washer

My dishwasher after the cycle is over still have a bit of dirty water remaining on the bottom. After few hours is getting more and more dirty water. I have a feeling that some kind of the valve is not working correctly which allows the water from the sink drain to come back? Am I right? Is it a big re[pair or marginal? My dishwasher is about 20 + years old and still the greates one I owned ( I had before Bosh ). I own the dishwaser for last 4 years but previous owner loved it and never repair


Hello Ma'am/Sir,\012 The Best thing you're going to do is to have new Dishwasher.A lot of brand new products can help you, rather than striving the old one...Hope it will help you! God Bless you...Thank you! ... Miele Dishwashers

Hello, Our kitchenaid DW has stopped working. Non of the buttons cause a any of the lights to turn on. Of course, it will not start. On its last working cycle, it had a very strange washing cycle. It almost sounds like the water was not splashing around (even though I opened it while it was working and noticed water at the bottom). I checked the circuit breaker, and it is not tripped. For a couple of weeks, the DW had started making a kind of metallic noise while in the washing cycle. Also,


It is nice to see a problem described with such a depth of observations. It helps in closing on to the possible causes of the problem.\015\012\015\012For the moment let us make sure there are no remnants of the glass left in the dishwashe ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

My viking dishwasher is blinking normal wash and light china wash and water is on he bottom of the pan. I have tried cancel restarting it nothing is working. The water is very hot also. Thank you... someone please help!


... Viking 24 in. Professional Series DFUD140 (Premium) Built-in Dishwasher

- the dishes and glassware on the top rack are not coming out clean - I checked the course strainer to see if it is being blocked but don't see any thing there - I also took out the spray arm that sprays up into the top rack and ran water through it with a hose - it also appears to be free of clogs. - I don't see the spray arm spinning when I open the door during the wash cycle - - lastly, it may be unrelated, but the dishes are not coming out of the washer as hot as they used to be any i


... KitchenAid 24 in. KUDI01DL - Multiple Color Built-in Dishwasher

Takes more than 2 hours to complete a one hour cycle. Will sit on "1" minute left for the last 45-60 mins. If the door is opened during this long one minute the washer still has water in it and will reset to 13 mins remaining.


Hello,\015\012\015\012Welcome to fixya.\015\012 \015\012**What I`m about to share applies to Almost all Electronic control B/S/H/ dishwashers. That includes Bosch, Thermador ... Bosch SHU5315UC Dishwasher

Dishwasher won't drain. (Kenmore 3380957Rev A) It's been not draining that well for a couple of months, but then a couple of weeks ago, it just won't let the last inch of water out. --I can't see in the center area under the plastic to see if something is clogging it. --I tried running it on three different cycles to see if that changed anything (Pots and Pans, Normal, and Water Miser). No difference. It never seems to overflow, but when the cycle is over, it has a couple of inches of


The problem could be the pump, the drain hose or the timer. It will not drain if left to sit. The thing to try first is to put a cup of white vinegar in the machine and let it wash. This may remove sludge or scale blocking the strainer. 2nd take the ... Dishwashers

We have a +11 year old Bosch SHU3006/UC/U06 that never leaves the wash cycle. We had to stop it during our last test run at 3 hours. Chat advise is suggesting a water temperature problem (I origionall thought the timer), suggesting that the cycle will not advance until it hits a set temperature (170 degrees). We checked and noticed that the water in the machine was only around 90 degrees during a wash cycle. We do not have exploded views or parts drawings, nor electrical schematics. I wou


Check continuity of the heating element to see if it is broken/open.\015\012\015\012The dishwasher prefers that the incoming water (water heater) be 120 degrees (F) ... Bosch SHU3036UC Dishwasher

Bosch SHY66C My Bosch dishwasher won't fill with water.  All electrical connections are fine and I can hear it make a sound as if it is trying to start about every 2 minutes.  There was water in the bottom so I used a shop vac and pulled it all out but it still won't start and is doing the same thing.  I checked the solenoid with a multi-meter and it appears to be working.  My power went out last night for about two hours and that's all I can think of that might have affected it.  The dishwasher


I'm a novice on this question, but i agree with the above statement about check the stuck float switch or check for a bad safety switch or lockout switch of some sort. I would suspect something is definately faulty in that area. Will the dishwasher r ... Dishwashers

My Maytag Quiet Series 300 is not cleaning my dishes very well at all. My glasses always have grit left in them (even with Jet Dry), my coffee mugs have film left in the bottom of them and now even my plates and bowls aren't getting clean. I don't even put my pots or pans in there, so I'm not sure where the grit is even coming from. We have city water and I use a powder to clean with. Also, there has always been a film of dirt that never seems to get rinsed away right where the door opens. Also,


First problem: The film on dishes and glasses. Try another detergent. Manufacturers removed all the phosphates from dishwasher detergents and there are many complaints. I have had good luck with Finish Quantium tabs. Also have purchased Cascade i ... Maytag 24 in. MDB5600A Jetclean II Built-in Dishwasher

We lost electricity very briefly today which caused the dishwasher, washing, drying, clean buttons to blink when the electricity came back on. I opened the door to do a load of dishes hours after the electricity came back on and the basin was filled with water which caused water to spill out of the dishwasher. The basin was empty last night when we used it. It seemed to fill up when it was not running.


It seems unit fill valve is stuck open and water is coming in even when machine is off.fill valve opens up only when u start the unit.2 chks this u can open the door and look at the hole inside from where water comes in.if water is coming in with do ... Frigidaire 24 in. PLD2850 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1214 seconds