Having problems with your Bosch 24 in. SHU43 Built-in Dishwasher ?

This is a very good web site. Thx for pulling it

\015 This is a very good web site. Thx for pulling it together. Have a Bosch SHU6800. Seems to run fine, except water sometimes pools in the bottom, results in foul sour smell. Bottom screen is clean. Suspect build up in drain line. Any suggestions? Dave in Seattle\015

Answers :

It is possible the check valve is sticking causing sour water to come back into the washer. The check valve is located where the drain line connects to the back of the dishwasher. Also make sure the drain line is higher than where the line connects to the drain under the sink. Most washing machines have a loop built into the line but it helps it to drain better when the line is higher. Try hooking the line to the top of the cabinet under the sink if possible.
Repair Help & Product Troubleshooting for Bosch 24 in. SHU43 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

This is a very good web site. Thx for pulling it


It is possible the check valve is sticking causing sour water to come back into the washer. The check valve is located where the drain line connects to the back of the dishwasher. Also make sure the drain line is higher than where the line connects t ... Bosch 24 in. SHU43 Built-in Dishwasher

Pull my pump first startsthe pressure is good as soon as i pull the trigger the pressure is gone as long as i hold trigger just faucet flow let go of it pressure builds up until i pull trgger , no pre


... Annovi Reverberi RMW2.5G25D

I have a Frigidaire dishwasher and there is not any water coming out of the top wash arm. There is good water pressure coming out of the lower washarm. I pulled out the dishwasher and can see the water going to the top washarm through the tube and it goes up very slowly. I took out the "check ball" below the lower washarm and it worked good. I put the "check ball" back in and ran the machine on "Upper Rack" and it still does not have any water coming out of the upper washarm. It doesn't seem lik


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. Please check that there is no gunk or mold\015\012behind the filter screen and under the cover at the bottom. N ... Frigidaire PLDB998A Built-in Dishwasher

F2 Code Hey, I have a single drawer built in Fisher & Paykel dish drawer and today I pulled the spray arm, filter and large metal screen out to clean them as we have been starting to get a bit of stuff left behind after washing lately. That was all good After putting it all back in though I went to use the dishwasher and it stopped and came up with an F2 fault, I thought I may not have put the bits back in properly so pulled them out again and noticed that on the rotor that connects the motor to


Fault F2 means the rotor is not rotating. If you say some of the vanes have broken off, they could have been jamming it. This should spin freely with minimal force when installed correctly. If you removed the rotor itself, you do ned to take care whe ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Pressure Washer Purchased in 2001. Used about 30 hours. It is very hard to start if at all. Good gas, good spark plug. Sometimes it will start within 50-100 pulls. After getting started, if you release hose trigger it will cut off. Any suggestions of what else to do? Thanks in advance.


I would look into getting the carb rebuilt, sounds like there is some gummed up valves. ... Pressure Washers

8hp honda engine on log splitter. costantly stalls as governor opens throttle to maintain rpm. engine starts to stumble then stalls. When revved with throttle acts similar. somewhat better when hot, somewhat better at half choke. have pulled carb and checked bowl, float, pulled main jet checked, blew carb out but no better. No dirt or gum in carb, looked new. all gaskets looked good. engine has low hours.


... Honda 8 HP Engine

No kinks in the line. Vent at sink is clear. Will pump some water just not all of it. Pulled left side panel off and removed hoses-no blockage. Pulled drain hose off and turned plump on, seemed to have good pressure/volume. Is this a timer issue? or control panel? Model SHU4022UC/U06


Alright, so you have a Slow Filling Dishwasher. In order to keep small particles of dirt and minerals out of the pumps and nozzles of dishwashers, manufacturers install a small screen in the primary inlet water line to trap any contaminants. Over ti ... Dishwashers

Pull cord seems to grab and can't get it to start since it grabs too quickly..... tried pulling it out slowly and then let it feed back... no good... manual doesn't address this at all


... Karcher G 2600 VH Gas Pressure Washer

I have a Karcher 2,600 PSI 2.3 GPM Gas Pressure Washer G 2600 VHR that I have used once last summer. I have stored the PW in my basement with no fuel in the gas tank. The PW was never exposed to freezing temps. I cannot get the PW to start. I put new fuel into the tank, the oil is good, I drained the carburetor, and the spark plug works (tested it). I pull the cord and the engine doesn't turn. Fuel value is on, choke is pulled, and the starter switch is turned on. System is practically brand new


Hi I have a similar pressure washer from Kartcher and the same scenario as yours I have owned it for about 2 years and noticed that it was getting harder and harder to start with each time I use it which is months. If your pw has a honda engine on i ... Karcher G 2600 VH Gas Pressure Washer

I HAVE A NEW CRAFTSMAN PRESSURE WASHER WITH KEY START. I HAVE USED IT ONCE AND WHEN I TRIED TO START IT IT WAS HARD TO START HAD TO PULL START IT. NOW IT WONT START. LET PRESSURE OUT HAVE HOSE OH AND RUNNING, NEW SPARK PLUG HAS OIL, GAS FILTER FINE.HAS GOOD COMPRESSION, BUT WILL NOT FIRE GET SOME RECOIL. GETTING GAS TO SPARK PLUG AND GETTING SPARK. IM LOST PLEASE HELP.


... Pressure Washers

Pump loses pressure after you use it a while even when trigger is never lifted . i can start it up it runs good trigger pulled and then it loses pressure no cavatation


Looks like you need a new diaphpragm in the pump unit ... Northstar Pressure Washer 3000 PSI

My kenmore 24" built in leaks from the top of the door. The door looks good. I am thinking the latch may not be pulling it tight as it should.


You can adjust that latch with a screwdriver. just take a close look at it and loosen the screws to adjust it ... Kenmore 24 in. 15079 Built-in Dishwasher

My coleman powermate 2750 pressure washer locks the engine up when the trigger is pulled. after a few seconds you can restart it.it comes up to good pressure but kills the motor. Some have told me they thought it was teh pump, but the sprays a little. I would think if the pump was bad it wouldn't spray at all? Comments?


All i can say is its not a good mechine I owen and repair washers and pumps and use them in line of business thats all i can tell you sorry ... Coleman Pressure Washer PW0881800

Maytag MDB6000AWB runs good. Steam coming out from under counter in back of machine. Machine is installed in a peninsula. Can't find a break in supply line. no evidence of water when unit was pulled out to look for water leaks.


Called repair man ... Dishwashers

Door dropped Opened door on my FDB421RFR and a loud cracking noise occurred - now the door drops quickly. I guess the spring(s) have broken - does anyone know if the spring is on the rhs looking at the front? I sure hope so, I can probably access that side without pulling the unit out! Is it good to spray these with WD-40 or do they just age anyway?


... Frigidaire 24 in. FDB421RF Built-in Dishwasher

When pressing any front button on the control panel nothing will light up or start up in any manner,does look like it did not finish draining,have water sitting in the bottom. Pulled off front access panels no signof burned wires or anything becoming disconnected? do have small childern in the house pressing buttons? power is good going to unit.??


1)check any fuse blown in board.\015\0122)check supply to the board. ... Kenmore Dishwashers

Pulsating motor, turn machine on pull trigger, it works but not very good, let trigger off, and motor pulsates quite rapid


... Pressure Washers

No heat -element is good. Heating contactor not pulling in,no 24 volts to contacter coil


1)check the heating element continuity&body resistance ok.\015\0122)check the thermostat series with the coil connection get tripped.(relay from board damage) ... Hobart AM14C-155 Dishwasher

Stalling Engine starts good cold, when it gets warm and you pull the trigger it dies. And it will not restart when it is hot.


Likely you air to fuel ratio is too lean, runs mean and hot but under load dies. then floods the carb.when it happens pull the plug ,kill engine :is there a lot of gas or none.remove the filter and watch the action of the carb ... Karcher 2500 PSI Pressure Washer

ASKO 1595 daer greendude, indeed your troubleshooting was right!!!! i pulled out the dishwasher and the base was full of water. once i got water out, the fault sign went away and it's ready to run its normal cycle. now i need to figure out where the leak comes from: either the fitting or the valve itself. just in case i have to replace the valve: any good source to get it from? i live in california. once again, thank you much!!! i'll keep you posted on the developments


I live in australia our part no is 8052120 ... Asko D1776 Stainless Steel Built-in Dishwasher

Middle and top spinners do not spin The pump is pushing water up the back delivery tube. There are no dishes in the unit and I was able to trick the door into thinking it was closed so I could watch what was happening. Or Not Happening The spinners are completely free of calcium or soap build up and both top and middle are easily spun with a finger. While the pump and bottom spinner were working, I pulled the top drawer out partially and there appeared to be a good flow of water coming out of


Hi,\015\012 Remove each spray arm and check it is clear of food particlesat the jets. The next problem may occour at the rotating joint . If the seal is not good, you can loose a lot of water out of this point.. If both of these seem reasonable ... Dishwashers

Hi i have inherited a karcher kb9040.it has only been used 4 or 5 times so i dont realy know how it should sound when. water is suplied to it it surges when you pull the trigger you only get the presure of a good hose pipe jet should the motor speed up when trigger is pressed regards ****


Hi there!\015\012 when you got as good as pipe pressure,you need to accelerate the speed motor to have a good pressurise water for your purpose,the pressure washer has a surge regulating valve as you trigger water gun the pressure blow up, ... Pressure Washers

I have a Kitchenaid dishwasher model KUDS01FLSS2. I finished replacing the door balancer cord and started the dw up and it started leaking underneath from the bottom somewhere around the middle of the unit. This is when it first enters the cycle, so there is no water inside. I pulled the DW out and look at the hoses and components under the DW and all looks in good shape and could not detect any cracks. However noticed that one of the hoses (not sure what the hose is called) that connects to the


In this Kitchenaid dishwasher model KUDS01FLSS2, the whole motor and water pump assembly simply sits (I think loose) in the bottom of the DW. From the inside, it is the round mechanism where the sprayer is mounted above the chopper, all one piece sit ... KitchenAid Dishwashers

Kenmore ultra wash #15765 will not drain. purchased 1996, web says no such model exist, but i have the manual, and it does, i need help . I have taken out the lower sprayer arm and the spinner that chops up the food left, even removed about 10 screws that hold down what looks like a filler but it did not allow me to remove it. How do i access the drain to see if it is stopped up. Do i need to pull it out from the counter and go from the drain hose,or somehow go in from the bottom??


... Kenmore Dishwashers

Trying to pull out dishwasher from countertop but it just wont budge! even opened the door and gave it a good tug but no luck! help


Hi,Did you remove the screws from the counter top??? Usually they are held in by a couple of screws through tabs at the top of the dishwasher...open the door and then look up...other then that I would have no idea what is holding y ... Asko 24 in. 1805 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0258 seconds