Having problems with your Bosch 24 in. SHU43 Built-in Dishwasher ?

Dishwasher pan constantly fills with clean water causing it to seep out of door


Answers :

The float switch or water level switch is stuck. In the bottom of the dishwasher in the tub there should be a round cover that looks like it has no purpose. Remove the cover which should be held on by a 1/4 head screw. Once this screw is removed the float should be visable Check to see no food particles are in the cover causing the float not to fully extend. If the float can be moved up and down easily then look under the dishwasher and you will see where this float is connected to. This is the water level switch and is may have gone out. You will see it is easy to replace
\015\012Dave
Repair Help & Product Troubleshooting for Bosch 24 in. SHU43 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher pan constantly fills with clean water causing it to seep out of door


The float switch or water level switch is stuck. In the bottom of the dishwasher in the tub there should be a round cover that looks like it has no purpose. Remove the cover which should be held on by a 1/4 head screw. Once this screw is removed t ... Bosch 24 in. SHU43 Built-in Dishwasher

We lost electricity very briefly today which caused the dishwasher, washing, drying, clean buttons to blink when the electricity came back on. I opened the door to do a load of dishes hours after the electricity came back on and the basin was filled with water which caused water to spill out of the dishwasher. The basin was empty last night when we used it. It seemed to fill up when it was not running.


It seems unit fill valve is stuck open and water is coming in even when machine is off.fill valve opens up only when u start the unit.2 chks this u can open the door and look at the hole inside from where water comes in.if water is coming in with do ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

My dishwasher emits a dead animal smell immediately after filling. I have a 20-year-old KitchenAid KUDS220T3 dishwasher. The racks are a little corroded, but it still cleans dishes just fine. About two months ago, it started smelling like a dead animal immediately after the dishwasher fills with hot water, during the time the water is being heated, but before agitation begins. The smell appears to be coming from around the door. If I open the door, everything inside the dishwasher smells fine.


This vent that you are describing is to allow air to flow in for the heat/dry cycle. Some times little creatures want to "mark" their territory by "spraying". Spray some type of cleaner like ammonia into it and **** it out with vacuum a few times. Mo ... KitchenAid Dishwashers

Kenmore dishwasher. The upper rack is not getting clean. Even very light residue remains. And, detergent is left in door at end of cycle. The bottom is filling up, so I don't think it's the intake valve. Also, all the blade openings appear clear. I am noticing that hot water is not filling the dishwasher when I first run the cycle. Even if I have hot water running in the sink, the dishwasher fills with cold or warm water. So, I think this is the problem. What should I do? Thank you in advance!


I find it odd that the dishwasher is filling with cold water if the water is hot at the sink. It sounds like the dishwasher is connected to the cold water line rather than the hot. Check under your sink; if you've got standard plumbing, the dishwas ... Dishwashers

Diswasher TYP NBKH, SERVICE 8546 892 10010 Problem: For all programs except rinse and charge 1/2 for all programs. Pre-rinse and rinse for 50 Bio, 60 and 70 OK. Downloading water to wash causes multiple knocking (on the left side dishwashers) and simultaneous blinking light (relais?). Opening doors and adding water (different amounts - from 0.5 to 2 l) brings the normal work of dishwasher back. Rinse with cold water after washing OK. Final cleaning with hot water causes knocking again. After r


... Dishwashers

Dishwasher hey! i have a frigidaire dishwasher. turns on, fills up with a little water and just sits there for about 10 mins doing nothing. starts to clean then nothing some more. it drys everything but leaves the dishes totally filthy even though they are well rinsed prior. after they are dry, the dishwasher then pushes out the remaining water like it is supposed to and on into the disposal. any ideas? i cleaned the pan out completely and replaced the lower parts. thanks!


DEAR FRIEND,\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012ngfam1 here for you!\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\0 ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

A GE triton dishwasher causes hammer noise when stops filling. The sink faucet works fine as do all the other faucets in the house. I cleaned all of the traps in the dishwasher. Because the sink works, I don't think it is a sink valve problem. I turned off the water to the house and drained the system, the air chambers should be good. Is there some component of the dishwasher that could be causing the noise? Would cleaning the pump help? If so, how would I do that?


The cause of the hammering noise, (slamming) is due to the water inlet valve on the Dishwasher (DW) shutting off abrutly once the DW reaches the proper amount of water.\015\012\015\012If this is an older DW, you might want to replace the ... GE Dishwashers

Ge Triton dishwasher GSD5500GOOWW was not cleaning like it used to- I cleaned screens at back bottom-very dirty- also-detergent cup stuck opne - took door apart and got it unstuck - it works fine now. - it seemed to do better but now it is cleaning poorly. It seems to fill and start a lot sooner than before - after 30-45 seconds it starts up. I tested the water temp and it is 90 degrees! Hot water coming in is at 105 degrees. Also - it is leaving a white residue on dishes - didn't do that be


Hi,The scum, film and white\012residue problems have started since the reduction of\012phosphates in dishwasher detergents.Here is a tip that\012will help you to solve the problem of films, residue, and scu ... Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103

I have a Kitchenaid dishwasher. Mod # KUD102CRBS1 which is hardly 2 years old. The door keeps separating from the trim and water seeps out, I fastened the trim, this took care of the problem for ca 6 month, now it is leaking again from the door, has anyone the same problem? I am steaming mad, this was an expensive appliance, which could only clean dishes somewhat with one brand of detergent, all other brands leave a gray film, and now this! MY previous dishwasher was a rel. basic GE but it got t


This is a fairly common one... I always use a silicone sealant/adhesive to make sure it stays put. A thin film does wonders. ... Dishwashers

Hi I have a Bosch dishwasher model SGS43T72GB/09. It has been working normally until lunchtime today and we noticed water pouring out of the door. We emptied the water and realised that the fitler was blocked with grease. We have cleaned the filter and tried to reset it. There is no water in it but all three lights are on check water, active & end when we try to reset it. If we put it onto a cylce active light comes on and you can hear it doing something but its not filling with water. Can you


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

I have the Siemens SL84A305UC Dishwasher. All of a sudden it stopped cleaning dishes, but everything sounds normal and it fills and drains water, and sounds like it is completing the cycle. In the past when I opened the door while it was actively washing the water would spray out aggressively. Now, when I opened it while it was supposed to be washing I see just a small amount of water coming from the bottom wash blade, and not even enough to turn the blade very far. I thought it was just a c


... Siemens 24 in. SL84A305UC Built-in Dishwasher

Hi. I have an LG LDF7810 dishwasher. I did a deep clean and ended up taking out a bunch of grease from the seal between the door-bottom and the tub. I even removed the door to get at the grease I thought was trapped back there. Since then it has been leaking water, sometimes a drip and a couple of times a few ounces have gushed out at the end of a fill cycle. Did I remove some factory grease designed to seal the door bottom? If so, what should I replace it with? If not, what else could the


It is possible that while you removed off the grease the water seal/oil seal was also damaged. Once the seal is taken out it can loose the sealing strength which can make it possible to leak.\015\012Hence it will be good to remove the seal and ... LG 24 in. LDF7810 Built-in Dishwasher

My whirlpool dishwasher is ocasionally filling back up with water, whether the door is open or closed, and regardless of of control panel being lit. It happens, then leaks out the front. If i run the cancel drain, it will pump out the water just fine. All the other cycles are working just fine, and it leaves no water at the end of of the cleaning cycle. I have found no common occurance for this


Greetings,\012\012 in most instances the water inlet valve is leaking..this is the water valve that brings water into the dishwasher...its possible, the drain water is running back into the d/w from the drain hose not installed prope ... Dishwashers

Hi there I have a Bosch SGV4313GB/17 Dishwasher the problem is there insuffient water pressure to feed the washer arm and they are not rotating Ihave cleaned the arms and circulation pump impeller with white vinegar ,I have also overriden the door switch and operated the dishwasher with arms removed and the circulation pump seem to be working but with insuffient pressure also the machine does not fill to the depth it did when it was fine! How does one tell if it is the impeller or the


Ours is a SHU3300UC/06 model, basic model which we bought in 1999 so have had 9 years of trouble free service.Recently\015\012we noticed that there was soap left in the soap dispenser after the\015\012machine had finished all the cycles. On fu ... Dishwashers

Whirlpool dishwasher part #3385181. Machine had gone thru wash cycle and was starting to dry. Smelled electrical burning smell, opened washer door and washer was filled with smoke. Turned everything off, cleared smoke, and the washer water dispenser is very hard to turn. Washer has symptoms of burnt up motor that turns water dispenser. Machine is 12 years old. With cost of replacement motor and possible part (pump?) that might have clogged and caused motor freeze up, is it worth fixing or junk


... Dishwashers

I am having issues with my dishwasher where it appears to be working but does not clean. Hot water does enter the unit and drains properly but is not cleaning. Muck is still on the door, the arms are wet. Also, normal cycle with no extra features selected (i.e. High Heat, etc.) takes over 1 hour and 20 minutes. Sounds appear to be normal, draining, filling, etc. Thanks!


No\015\012 you need not wash the dishes but just cleaning of the debris and then \015\012putting it in the dishwasher for proper cleaning will help you to \015\012prevent the drain from getting blocked.\015\012\015\012 ... Dishwashers

I have a Bosch SHU43C05UC diswasher. Last night, I put it on before going to bed as usual. I was awakened a couple of hours later to a loud grinding sound (like a pump being run dry), and found the noise coming from the dishwasher. The display read "0" time remaining, so I opened the door and the dishes seemed clean, so I left it shut off. Tonight I have been trying to troubleshoot the problem. The dishwasher will turn on, but it will not seem to fill with water. I have verified that the


Ok well before you can do anything you must obtain a service manual, link below.\015\012\015\012http://allrepairmanuals.com/bosch ... Dishwashers

My dishwashing isn't filling properly. I think there is residue on the float "thingy" (located on the bottom right side close to the door) and it doesn't float like it should, so the dishwasher thinks the water level is correct when it isn't. How can I clean it and get rid of the gunk that is keeping the float from floating?.


It appears you already have someone providing solutions on this posting. Unfortunately I am not able to see the responses.\015\012\015\012It mgiht help if you can provide the full model number of the dishasher.\015\012The float shou ... Westinghouse Dishwashers

Water won't stop filling, even when the door is opened. I cleaned the float valve at the front , that worked for a few washings. Or it may be a random occurrence. This dishwasher was purchased in 1993 in Canada, and has always worked well. We do have well water, but it isn't real hard, I put vinegar in about nearly every rinse cycle.


... Maytag 24" Built-In Dishwasher - White

I have a bosch SHE58C dishwasher. The cycles all work, it fills so the water line is ok, it washes, and it drains so it is not clogged. I cleaned out the sump and it is all clear. However, I think the "brain" or control module is bad. When I try to run a cycle, it does not fill. One other note is that it continues to run when the door is open. Is there a way to reset the "brain"? I've tried killing the circuit breaker


I have a similar problem with my SHE55M15UC model. I bought it last week and I had to push and hold the cancel button before it would start another cycle. If it doesn't finish the previous cycle, it will not let water in. Also, mine doesn't shutoff ... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

I have two problems with my GUI1500 dishwasher. The 1st is that when water starts entering the dishwasher I hear a loud hammering/vibrating sound. It's strange, but the sound will stop if I turn on a faucet in the house. The other problem I have is that the soap dispensor will no longer stay closed. The Plastic tab that holds it shut has basically disintegrated. Will this cause the dishes to not come clean? Can this part be replaced? I don't see any visable screws holding it onto the door.


Hi - welcome to FixYa,\015\012\015\012The first problem isn't a fault with the washer, it's a plumbing problem called "water hammer", which is a resonating vibration through your pipes. It's usually caused by a toilet flush valve, but can ... Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of water is let in when the pump turns on and the washing cycle begins. Opening the door shows that the water level does not reach the bottom of the float. When I close the door, the wash cycle begins again but stops after a few seconds. This is when the water begins to fill again. This time, the wat


Larry,The float is generally for overflow conditions and will interrupt power to the fill valve solenoid. If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water ... Whirlpool GU2400XTP Built-in Dishwasher

Kenmore dishwasher will not fill with water model no 630.1609406. It will run a full cycle but not fill. Water was temp shut off to replace kitchen sink and now dishwasher won't fill with water. No fill valve that I can see cleaned filter but still no water.


First, are you sure that the machine is not filling?\015\012I go on calls all the time for this problem and it turns out than the machine fills but the wash motor does not run.This leaves soap in the bottom of the DW so it looks like it did not ... Dishwashers

Inglis MOD#IPU58460 Dishes not cleaned properly...thought that enough water was not being filled into tub because more water added manually and washes great! I checked inlet water valve operation and lines for possible lime buildup and timed "fill" time. All was good and time right to spec! Water level after fill is just to bottom of mesh screens. Under further trouble shooting I held door open slightly while holding door switch closed to observe wash cycle and found as pump starts water shoots


The sprayer arm may be clogged with debris.Here's a step-by-step troubleshooting guide. ... Dishwashers

I have a Kenmore Model 665.15955792 dishwasher. Water is leaking out the bottom of the door. I changed the door seal and the defusers but it continued. I took off the front of the door and I see the water filling into the base of the machine. When the dishwasher starts the cleam cycle, water is pushed up into the small square holes in the bottom of the door and then splashes up over the lip of the door and out onto the floor. It has never done this before, just started recently. I have had the d


... Kenmore Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2270 seconds