Having problems with your Bosch 24 in. SHU43 Built-in Dishwasher ?

My Bosch dishwasher SHU43C02UC/38 runs the quick wash cycle in an erratic way - seems to get stuck at the last stage of the countdown ("1") and, I think, goes back up and runs again. Instead of +/- 40 mins, takes an hour and a half.


Answers :

Hi,

The issue with your Bosch dishwasher likely lye`s within`the electronic timer/control, specifically the heater relay solder joint. ( a faulty flow switch, ntc or heater can also cause this, but not very probable ). This is the purpose of the "1" indicated in the display, a heating problem.

I`d first suggest calling in an authorized bosch servicer, however If you feel capable there`s a way to visually inspect the control. It will require you to remove the control from the unit and then remove the control from it`s plastic housing and look for a burnt solder contact on the printed circuit board. This will be one of the pins from the heater relay, hence the unit sit`s at "1" ( because it can`t heat to advance or until canceled ) trying to heat the water.

**Further to this, if you or someone you know is proficient at soldering, a lot of times it can be remedied by simply repairing the solder...although Bosch recommend`s replacing the control and I don`t pretend to speak on there behalf nor do I profess to know better. This is just my experience (it work`s) and my opinion (why buy new if one can repair ?)**

**Please disconnect the power before attempting any service to the dishwasher. If you do not feel comfortable attempting this service, call a local pro, preferably one familiar with Bosch/Thermador/Gaggenau, to service your machine.**

Hope this answer`s your question, let me know if I can assist you further. Thank`s for visiting "fixya" for your repair inquiries. Please take a moment and rate this solution and leave a testimony.

Good luck.

macmarkus :)
Repair Help & Product Troubleshooting for Bosch 24 in. SHU43 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Bosch dishwasher SHU43C02UC/38 runs the quick wash cycle in an erratic way - seems to get stuck at the last stage of the countdown ("1") and, I think, goes back up and runs again. Instead of +/- 40 mins, takes an hour and a half.


Hi,The issue with your Bosch dishwasher likely lye`s within`the electronic timer/control, specifically the heater relay solder joint. ( a faulty flow switch, ntc or heater can also cause this, but not very probab ... Bosch 24 in. SHU43 Built-in Dishwasher

Takes two and a half hours to run a load of dishes


They probably aren't running the hot water at the sink before starting the dishwasher. You know how it takes time to get hot water at the tap when you turn it on? well the new dishwashers use such little water, that they will fill with cold/warm wat ... Dishwashers

Frigidaire FDB520RHB Dishwashers : We bought this dishwasher about 3 months ago. Today I ran the washer before I left to do errands and when I returned, I believe the washer had finished its cycle. But about an hour later, I noticed it had started up on its own? It then proceeded to run for almost 3 hours before my husband canceled the cycle. We were kind of waiting to see if it would stop on its own, which is why we let it go so long. I think it usually takes about 1 1/2-2 hours to wash. Could


Try to run the dishwasher on a short cycle like rinse and see if it finishes the cycle.It is likely the heater or hot water temperature is not reaching the desired level and this could cause the extended wash cycle. Feel water temperature ins ... Dishwashers

Won't Stop My dishwasher has only been used about four times but when I switch it on, it will go on an on for hours and hours until eventually we just have to switch it off. It doesn't dry the dishes just continously sprays water on them. The timer runs down but then just goes back up and starts again as though it keeps repeating the cycle.


If your dishwasher's cycle times are too long, check these:Water pre-heatingCycle not completingWater pre-heatingYour dishwasher may pre-heat the water. If so, and if the water entering the dishwasher is cool, the ... Neff 24 in. S5456 Built-in Dishwasher

Fisher & Paykel single SS Dishdrawer. Cycle's stuck. Normally sticks at 137mins and 33 mins, has stuck on other times too but it's always on those times. Have tried pausing and opeiong the drawer int he hope to kick it back into working but doesn't help. A normal cycle of 151mins is taking 4 hours.rnI normally have to let the cycle run till it sticks on 33 mins then I trun it off letting the dishdrawer empty and kick into dry mode. I hate to see my next electricity bill, its been a month n


My dd603 takes 3 hrs to do a 55 minute cycle-who can help me ... Fisher and Paykel 23 in. DS603H W Built-in Dishwasher

This problem is intermitten. Kenmore 665 16765690. starting the dishwasher, I hear a motor running. I think it is trying to empty water, however there isn't any water. I will turn the time rotor around to the start again. Sometimes, when I do this the motor running sound has stopped and I hear gurgling sound of water entering. Once this happens, the cycle is good and does well. However, there are times, rotation the timer back to the beginning may take several times, up to about 20 times.


Hiclean water filterthe presure is to lowPls vote me to keep us alive ... Kenmore Dishwashers

The display keeps cycling thru some gibberish and wont run right. when i hitstart, it runs for the dislpayed 5 mins and counts down correctly, reaching "00" and then goes back to flashing gibberish. It will not let me chose a cycle on the inside either, as in "heavy", "fast"... please help


Not sure if you have fixed this problem yet. If it is happening only in one drawer then get a clean damp cloth and clean the key pad inside the top right of the door. Also clean the edges as well.\015\012\015\012If the other drawer is OK ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

I have a Bosch SHE46C06UC/33 and get down to 1 mins left and then goes back to 55 mins or so.. It takes 3-5 hrs for a complete cycle,, any idea's.. thanks,


I have the same problem. I made a video here. What's a good place to buy a replacement? http://youtu.be/IjYomVSI3hI ... Bosch 24 in. SHU43 Built-in Dishwasher

My Beko dishwasher dwd 4310 w will run a full cycle but makes a choked, gargling sound and takes hours to complete a cycle. I mean 7-8 hours! There are long periods of inactivity with the machine before it goes into the next part of the cycle. It is the same on all settings. Please help!


... Beko 24 in. D3731F Free-standing Dishwasher

Dishwasher runs for appx 14 min & stops washing half way thru wash cycle. Timer contunies to run. No drain pump out (nothing). Let dishwasher set idle for appx 1 hour and it will re-set. Set timer forward to end of wash cycle and it will complete rinse and final rinse. Then go to dry. Timer works ok.


This sounds like something is stuck in the drain pump. You can remove the inner cover to look for obstructions. You have a dual purpose motor it does the both circulating and draining. The blockage is causing it to overheat and trip the thermal prote ... Whirlpool DU840CWD Dishwasher

DHB standup dishwashing machine, temp and high temp over heating,not working in proper temp range. only happens in the morning when after fist fill, will continue to overheat for about a half hour to 45 mins then machine usally begins to run normally at propper temps.looking for a cause.


... Champion 26 in. D-HBC Free-Standing Dishwasher

Hobart commercial under the counter diswasher LXIC Model Number 130016. DELIME light comes on every day at startup. Machine will immediatly run (in DELIME mode I think) for about 5-10 min and then get E4 error. We unplug power to the unit let it set, replug it back in after 3-4 cycles of this, it will eventually work perfect for the entire day. I have replaced the Sensor that is on bottom front of the unit in the water trough. ( I replace the sensor to the right if you are looking at the un


Q have your run a descaler . to rid the machine of its deposits . in order for the machine to run properly the parts and pump / screens must be clean . / descaling for deliming . dishwasher and icemakers is comm ... Hobart LXIC-6 Dishwasher

My boys are helping now but they don't rinse off plates first. Now the dishwasher is acting like it's not cleaning very well. I'll take the dishes that have stuff on them still and soak them and then put them back into the dishwasher. Are we filling it to full, I make sure the uper rack is clear on the bottome of it for the water jets to work. I was thinking about running some vinager through it. would that help with maybe some cloged areas


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Frigidaire 24 in. FDB510LC Free-standing Dishwasher

KitchenAid KUDP01DLBS2 dishwasher. Runs for a very long time on any cycle; time does not seem to advance. (takes 2.5 hours or more for normal cycle. "sensing soak", "water heating" lights on for a long time, even though it appears that water is not being heated. Checked incoming water temp, is hot. Did not do this when new, something has changed. Typical cycle was 1 hr 10 min. before.


Sounds like the heater inside the dishwasher is not working. The machine is trying to get the water up to a preset temperature, probably in the neighborhood of 140 degrees. That is one of the things that it is sensing.After the machine fi ... Dishwashers

Hi there My Bosch Exxcel Dishwasher is tripping out the fusebox RCD and I think there is an earthing problem. It will run for 3 or 4 minutes and then the house alarm goes off and the cooker clock needs resetting! I have tried to look in the back but don't know how to remove the panels. I've tried tipping it to 45 degrees to see if there is any water in the innards but non water came out. I have no idea what to look for - and no manual to help me get inside the beast! Thanks in advance.


It will probably be the water heater element is failing and shorting out.\015\012\015\012Be careful as you do not want to electrocute yourself ! ... Bosch 24 in. SGS45E02 / SGS45E08 Exxcel Free-standing Dishwasher

LG DISHWASHER, MODEL LDF6810WW, SER #706KWTA00393 ON STARTUP PUMP RUNS 10 TO15 MIN. BEFORE IT PROGRESSES TO NEXT STEP.THERE IS A LOUD HUM DURING THAT TIME. ALSO THE NORMAL WASH CYCLE TAKES ABOUT 3.5 HOURS. THE REPAIIRMAN HAS BEEN HERE 3 TIMES WITH NO RESULTS.


... LG LDF6810ST Stainless Steel Built-in Dishwasher

My pressure washer runs 4 about 20-25 min then it starts knocking and pinging then shutsdown it has plenty of oil i checked it and replaced it with 5-20 oil it starts hard always has if you let it sit for about an hour it will start back up sound fine and work good untill it happens again any thoughts to what might be happening to it?


Sounds like the engine is overheating either due to restricted air flow over the cylinder and head assembly, or the engine is running very lean due to a plugged fuel filter, dirty carburetor, or plugged muffler. Hope this helps! ... McCulloch FHH25A Gas Pressure Washer

Hotpoint FDW85 will not start wash cycle. Takes water in and thats it. The timer goes up and down. no error codes displayed. press cancel and it pumps the water back out. if I leave it running then i can hear a boiling or bubbling sound.


... HP Dishwashers

I have a troybilt pressure washer when i crank it up it builds pressure when i engange the pressure it takes about 5 seconds and pressure goes away if i let off the trigger it will build pressure again it only has about 20 hours of use on it (i did run a acid solution through it for my driveway wonder if that ate up a seal)


Unloader valve is the most likely suspect here.\015\012Remove and clean with penetrating oil then reinstall.\015\012\015\012Also add some LIGHT oil into your supply hose via a small funnel. 3-in-1 household oil or power steer ... Pressure Washers

Timer doesn't countdown (pauses for long periods) in the wash cycle. 3.5 hours to run a 66 min cycle. Model is the GU1500XT


Hello,\015\012The timer is bad and will not work correctly.\015\012You need to replace the timer.\015\012\015\012http://www.fixya.com/ ... Dishwashers

Karcher B402 pressure washer Motor runs as soon as power supply connected, on/off switch does not seem to make a difference and no pressure at outlet? Was working fine, stopped for half an hour, came back and wouldn't work. Thanks Bob


Bob I had this happen to my Karcher, the pressure seals have blown. $Au200 for service and replacement from karcher dealer. tyhey would not sell the parts for a DFY ... Pressure Washers

Dishwasher has been stored. Was working fine-ish for first half dozen washes. Now not starting wash. From troubleshooting in manual I'm holding down first two buttons and it's saying "End", but keeps moving back to SOAK function (17 mins) and not doing anything. Display shows whole soak cycle to run, but on holding down start button it makes no difference - doesn't beep to acknowledge and start cycle.


After bringing the unit from storage did you conduct any service on it? Did you remove any water before storing the unit? when you store a unit like this you need to totally empty the unit from everything including wate ... Smeg 24 in. DWF614SS Stainless Steel Free-standing Dishwasher

When i run the washer after 10 minutes it starts to leak oil the motor starts to labour and then gives up iof you ask it to wash it just hums if you leave for half an hour it goes again but then develops the same problem


... Karcher K2.26 Electric Power Washer

Engine starts runs good for 2 or 3 min the quites, will start right back up and run for 3 or 3 minutes, then shut off, will restart and run for 4 or 5 min then shut off.,


... Pressure Washers

My dishwasher runs 2 hours as a complete cycle. I think it is never going to finish but I have not stopped it in mid cycle. Dishes are very clean but they should when it runs this long. I hear it change cycles so I know it is not stuck on 1 cycle. It also makes a lot of noise. 2 hours of noise. HELP!!! How long it it suppose to run?


That means that the machine does not detect that one condition to continue the cycle is met.Sometimes\015\012 when this happen unesperience repairers replace the timer board , an \015\012expensive part that rarely fails. The timer b ... Whirlpool DU1055XTS Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1404 seconds