Having problems with your Bosch 24 in. SHU43 Built-in Dishwasher ?

The control panel on my dishwasher is showing a tap and E15


Answers :

E15 means that unit doesn't think it's getting water. Make sure the water to the unit under your sink is turned on and the dishwasher is getting water. If so then start a cycle and wait until the error occurs. If there is not water inside the tub then you have a problem with your electronic water valve and will need to have it replaced. If you do have water inside but it's still giving you the error, then you have a bad flow meter that iwll need to be replaced. At 2 months old all these issues will be covered under warranty at no charge.

Read more: http://www.justanswer.com/questions/36jew-my-bosch-dishwasher-is-showing-e15-and-the-tap-signal-is-on#ixzz0jMwGdek8
Mine's a bosch, same problem but started with E25 due to broken glass in the pump impeller, after struggling to remove it and then testing, it eventually moved to E15 as rightly so, no water was entering the machine due to the E25 code.\012 The advice above is good, but take the device out first and tip the machine. This cured my faults without the need for a service call or spare parts.
Repair Help & Product Troubleshooting for Bosch 24 in. SHU43 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The control panel on my dishwasher is showing a tap and E15


E15 means that unit doesn't think it's getting water. Make sure the water to the unit under your sink is turned on and the dishwasher is getting water. If so then start a cycle and wait until the error occurs. If there is not water inside the t ... Bosch 24 in. SHU43 Built-in Dishwasher

Dishwasher model en50242 after cleaning both filters and turning on the valve etc no water is going into machine. The control panel shows 2 lights one above the tap sign the other above the programe light. The pump runs for a few seconds then stops and nothing further happens. We are in a high water calcium area.


... Siemens Dishwashers

Pld2560lcc1 Dishwasher...Control Panel shows 65 minutes left on lower rack, works for about 1 minute, shuts down. None of the buttons work. I changed the control (major circuit) board, same problem. I wonder if it's the control "panel"? I took that off and looked at it. Seems okay, but could the problem. I've heard this model has control problems, but I'm not sure if they mean the major control board or the control panel that has the buttons.


Pulled the touch pad, go after the middle third with a very small screw driver, cleaned the flex circut with contact cleaner\015\012\015\012powered up fine seems to be working again ... Frigidaire 24 in. PLD2560LCC Energy Star® Built-in Dishwasher

PLD2560LCC1 Frigidaire Dishwasher...Control Panel shows 65 minutes left on lower rack, works for about 1 minute, shuts down. None of the buttons work. I changed the control (major circuit) board, same problem. I wonder if it's the control "panel"? I took that off and looked at it. Seems okay, but could the problem. I've heard this model has control problems, but I'm not sure if they mean the major control board or the control panel that has the buttons.


... Frigidaire 24 in. PLD2560LCC Energy Star® Built-in Dishwasher

Miele Optima Series 2470 Dishwasher sounds a beeping sound and flashes a F19 error on the control panel. Last week the beeping sounded and flashed a F13 error on the control panel. I looked in the manual and it said to clean the filter, which I did and put it back in place and locked it. Now the beeps sound and it is now showing a F19 error on the control panel. Help!!


... Dishwashers

An electrical panel breaker switch was replaced after the microwave and dishwasher both lost power. The microwave works after replacing the main panel breaker. However the dishwasher will not show any power. Checked the internal circuit board, no burned areas, cannot find an internal GFI reset, what can I do to get power restored to the main control panel or even the unit itself? Rick C


1)check any fuse in the circut board.(blown off)\015\0122)check any loose connection of neutral (or)phase wire to the machine(or)in the switch. ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

FDW70 dishwasher, starts to fill with water, shows pre wash on control panel, then pumps out within about 2-3 minutes, but has vertualy no water in it. Puts up code A10 on control panel, can still hear the pump going even when l open the door. Have replaced a burnt out heater tube with a new genuine unit, also have removed & checked fill valve & this works fine.


Hi,Try this few steps;Turn off the water supply to the dishwasher and remove the hose, turn\015\012on the machine for a couple of minutes in a fill position then turn off\015\012the machine, reconnect the hose, turn the ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

I have a Siemens SN25M230GB Dishwasher showing the following: Fault Code E15 Digital display showing (Error) E15 with a flashing 'tap' What does this mean? Is it something that I can fix myself or does it need to be looked at by a professional? Thanks Tina


... Siemens Dishwashers

Have a 4 year old Kenmore Dishwasher Model # 74382. No problems at all until last week I went to start it and it would not turn on. Lights on the control panel were on with exception to the start light. I opened and shut the door to make sure it clicked and pressed the start button again and nothing. I tapped around the panel with the side of my fist and pressed it again and it began working. Well today different story I went to start it and it did the same thing. I tapped all over front of the


The problem is more likely the door switch is failing or out of adjustment/loose. You will need to remove the door panel. This is easy to do. There is a video at ... Kenmore 24 in. 74382 / 74384 / 74389 Built-in Dishwasher

The control panel does not function and therefore the dishwasher shows no power and therefore does not function at all. Can I replace the parts to the control panel myself?


... Maytag MDBH965AWS Stainless Steel Built-in Dishwasher

We had a problem with our garbage disposal and it resulted with water leaking from our dishwasher. The disposal is fixed, I removed the excess water from the dishwasher. I tried to run the dishwasher empty to clean it. It runs but then the E-2 alert shows on the control panel meaning high water level. I read in the book that I may have to have a service person do some sort of a reset. Is this correct?


Contacted the company and they e-mailed instructions to fix problem ... Asko 24 in. 1895 Built-in Dishwasher

I have a Miele Dishwasher G1023U , after pressing on/off button the control panel light comes on in the drying cycle not the Wash/Rinse . Water does not come into the machine , can not turn it off at stop/start button only at Main on/off power button. Only had Dishwasher 2 weeks, was working fine. The water tap is on, no kinks in hose.


... Dishwashers

Dishwasher problem Hi We have a Whirlpool GU 2300, the machine has stopped and is the clean LED on the control panel is showing a 7 pulse sequence which I guess is a fault alarm. I have tried resetting, checked the door switch and looked at the pressure sensor at the drain pump outlet. I changed the heating element and fitted an uprated control card earlier this year. Any ideas?


I solved the reset by pressing the air dry and reset buttons 6 times in sequence, the whole panel array lit and I was then able to reset. I have had no problems since and have used it 6 times. I initially thought that the chipset had a volatile memor ... Dishwashers

The top drawer of my fisher paykel dishwasher stops during the cycle and shows an icon of a tap with a line threw it (assume that means no or low water pressure). the bottom works fine so I assume water pressure is not the issue; is there a sensor that could be bad? Also, I did switch the controllers between drawers (good instructions on the fisherpaykelparts.net website) but the problem stayed with the drawer, ruling out the controller.


Did it fill with water? could be 1 of your water valves is faulty, or the little filter for the inlet water is blocked. please reply 4 more help. i"m sure i can fix this problem for you. good luck. ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Dishwasher had all control lights on in the morning; touchpad would not work; cycled power to the dishwasher and now no lights on the control panel will come on


... KitchenAid KUDS35FXSS Dishwasher

Kenwood dishwasher KDW60X10 showing error E1 on control panel.


... Kenwood Dishwashers

Hi, I have missed place my manuel for my dishwasher. It is a single-draw stainless steel, model DS603. The problem I have is F1 is showing on the control panel and it has a beeping sound. How do I rectify this problem? Cheers


F1 means that your dishwashers have flooded. You can \015\012download the video in the link below to see how to get rid of the error and fix your dish drawer for numerous other problems.\015\012 ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

When I try to start the dishwasher, I can get the light to show I want it do do a normal load. Then when I hit the start button, it lights up but the machine will not sstart. Then in a few minutes the lights on the control panel at the top of the door go out. What can I do to fix this? The model # is KUDS011JBS0 tHE 0'S HAVE A SLASH ACROSS THEM THE TYPE IS 577-0 SUPERBA


Hi,\015\012\015\012Your control board has gone bad... you will need to replace it.\015\012The replacement is not very hard, just make sure that you mark where all of the wires go before removing them.\015\012\015\012Here ... KitchenAid Dishwashers

The control panel on my Electrolux/Icon dishwasher is not working. The only light showing is the red start/cancel light. When I press it to start, nothing happens and the light remains red. What could be wrong?


... Electrolux EDW5505ESS Built-in Dishwasher

I have a Bosch SGE63E05UC dishwasher that keeps intermittently showing an "E:25" error code. Occasionally it will get all the way through a cycle without going into error, but more often than not it will error and stop. So far the main control module in the front panel and drain pump have been replaced and the problem persists. All hoses have been checked and are clean (unit is only 1 year old) and drains well, when it does drain. Any suggestions?


... Bosch SGE63E05UC 24 in Builtin Dishwasher

Thor dishwasher Model No. D3764FS purchased in 2004, can't find users manual and have a problem ... A red light is showing up on the control panel just above a symbol that looks like a element ???? Have tried on the internet for user manual but had no sucess... Are you able to help me... thank so much


... Dishwashers

KUDIO1ILBS2 KitchenAid Dishwasher, two years old, not heavy usage: control panel is dead, no other power problems in the apartment, the apartment's electical box shows all breakers ok.


These dishwasher have a thermal fuse near the contol panel protecting the heat sensitive computer. Do you use the Sanitize or Anti-bacteria cycles?? If so then these cycles get very hot and could have made the fuse blow. Kitchenaid also had some loos ... KitchenAid 24 in. KUDI01ILBS Stainless Steel Built-in Dishwasher

Have mains power to printed circuit board but control panel shows no lights so i cannot start dishwasher


If you have power to the circuit board and lites do not come on then check the door switches in the front panel.The power will not be distributed without the door switches being made. It is a safety factor. If the switches are good then the control b ... Dishwashers

I have an electrolux dishwasher dx302wj*03 model. The fault code 50 is showing. Does this mean the control panel is faulty or the pump needs replaced? We have been able to fix other problems our selfs from the past and we have avery good store to get all the electrolux parts.


... Dishwashers

Control Panel won't let me hit the start button. The dishwasher is a little over a year old and is used at most once a week. The blue light on the bottom right of the dishwasher seems to no longer light up. The control panel will let me select the wash, but the start button and time indicator does not light up. Not sure if this a real defect and if just a simple exchange of the front control panel will fix the problem? Already tried resetting the circuit breaker and that did not help. Than


... Dacor Epicure ED24 Stainless Steel Builtin Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2050 seconds