Having problems with your Bosch 24 in. SHU43 Built-in Dishwasher ?

How to get to the control panel

\015 I need to replace the control panel but I can't get to the old one. Took out 4 screws but I can't get the cover off. Any suggestions\015

Answers :

Bosh is very tricky. You will probably have to remove the outer door panel first. #15 Torx screws all around the inside of the door panel. Support the panel with your feet while you remove the bottom two screws. (Do those last!) Close the door. Then slide the door panel down about 1 in and pull away at the bottom. Notice the two plastic blocks near the bottom of the door and how they fit onto the door frame (they never stay in place!)
\015\012If the console is not loose already, remove the two #15 Torx screws on the upper sides of the door panel.
\015\012When putting it back together, put in the screws across the top of the console first, then the door panel, then the rest of the screws.
\015\012Good luck!
Repair Help & Product Troubleshooting for Bosch 24 in. SHU43 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

MDB6709AWW1 Poor Quality Control Panel Our dish washer is 2 years old this month and the control panel broke!!! My service technician told me that he has seen DOZENS of new Maytag dishwasher control service panels break and is convinced it is a design flaw. When I called Maytag the customer service rep had the NERVE to tell me "that because the house is near the beach, I must get a lot of power outages and power surges, that is why the control panel broke." I told her I wasn't born yesterday


... Maytag Dishwashers

I have a Maytag quiet series 300, model # MDBTT60AWW. The front control panel have some green lights on but the start/cancel button won't work. The dishwasher will work for 5 days and quit for 2-3 days then work again. I tried to reset the main electrical panel hoping the dishwasher will reset too but it didn't work. I opened the panel on the front door to see if water is getting into the electronic panel but it is dry. I'm wondering if it is the front control panel itself is the problem. I want


... Maytag Dishwashers

The control panel on my Maytag MDBH970AW is unresponsive, and the latch is stuck in the "open" position (the plastic piece stays pushed in to the handle and won't come down). I've checked that the unit is getting power from the house. Last time I had this exact problem (when it was under warranty), they had to replace the control panel, the latch, and it seemed like most of the door. What should I do?


... Maytag 24 in. MDBH970AWS Built-in Dishwasher

Quit working during wash cycle, about 6 liters of water left in bottom, looks like it quit during rinse cycle. There is power to the door switch and door switch works shutting off power when door is opened. However the control panel does not respond to any push button. I have had a problem in the past with moisture from the door vent getting into the control panel area causing the push buttons to become eratic.


The capacitors in the control panel could be bad or have burnt out. Do check all connnections and if necessary, check the continuity of the power to and from the control panel with an ohm/voltmeter. ... Dishwashers

Control Panel On the control panel there is a light right next to the "Heated Dry" button that is on. It looks like a "3". It's lit up - and never has been before, and I can't get the dishwasher to start. How do I make it go away?????


I did not use your service to fix my problem - I found the answer on Maytag.com. But you charged me anyway - so I would like that money refunded. ... Maytag 24 in. MDB9750AW Dishwasher

Hi I have a maytag quiet series 300 with model # MDBTT60AWW and it will not start. All the lights lite up but it will not start. I recently just had to replace an element due to a recall so when he was hear fixing the element I asked him what he thinks could be the problem and he said it sounds like it possibly needs a new control panel. Does this sound right and if so do you know where I can get a control panel. Thanks for your help


... Dishwashers

Have a whirlpool gold dishwasher.The problem is that the clean lite on the control panel flashes not allowing the unit to work.I installed a new disposal and forgot to remove the plug for the dishwasher drain hose.When the flood happened I opened the door in order to stop the dishwasher.Now the unit will not work.The lite flashes 7 time ,then it pauses and flashes 7 times etc.Is there a reset procedure to run in order to get the unit to work or do I need to buy a new control panel?


HI,Can you please give the make and the model no. so that i can give you the manual.Waiting for your reply ... Dishwashers

My GE Profile dishwasher (model PDW9880L00SS) has an electrical problem. Last night, the dishwasher was beeping and the control panel lights were bouncing around as if someone was pushing the buttons. I managed to get it to run a cycle, and now the control panel is completely dark.


... GE 24 in. Profile PDW9880JSS Built-in Dishwasher

I have a Kenmore Elite Ultra Wash dishwasher. Model #17572. All the lights on the control panel went out. Get no response at all. Circuit breaker is fine. Any reset tips? Or, do I need a new control panel?


... Kenmore 24 in. 17572 Built-in Dishwasher

Getting to the control panel


The outer user interface / touchpad stays in place. it can be removed only after removing the electronic machine relay board. The relay board is accessed from the inside of the door. You need to separate the inner door panel from the outer door panel ... Bosch 24 in. SHU43 Built-in Dishwasher

My KitchenAid KUDS01FLSS0 won't turn on when the "Start" button is pushed. Several months ago it began requiring multiple pushes to get it to start. All the cycle lights on the control panel work when pushed - except the "Start" button. Online & repair parts person suggested I replace the: - Tail Cable Ribbon; did not fix problem, then - - Electronic Control Board (interface) which also did not fix it. Should I replace the Electronic Control Board that is actually the part with the buttons


... KitchenAid Dishwashers

I have a 4 year old Maytag MDBH945AWW and the panel lights come on and I can select cycles... but the dishwasher wont start. I tried holding the start cancel button, tried turning the breaker off for a couple of hours, took the inner panel off the door and checked the latch, but its still wont start. Any other suggestions? If it needs a new control panel its probably better to just get a new similar dishwasher for $300, correct?


What you need to do is read for continuity and power across the door latch switch. (2 white wires) AND 2 Black wires Both wires must read continuty at the control panel connectors to the power source terminals for the unit to start. Since the co ... Maytag MDBH945AWW / MDBH945AWQ / MDBH945AWB Built-in Dishwasher

An electrical panel breaker switch was replaced after the microwave and dishwasher both lost power. The microwave works after replacing the main panel breaker. However the dishwasher will not show any power. Checked the internal circuit board, no burned areas, cannot find an internal GFI reset, what can I do to get power restored to the main control panel or even the unit itself? Rick C


1)check any fuse in the circut board.(blown off)\015\0122)check any loose connection of neutral (or)phase wire to the machine(or)in the switch. ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

E6 I have been getting E6 error message over and over again. I have had the machine to pieces, cleaned out the pump and hoses, and still the same problem. Occasionally, the error message changes to E8 or E1, but no matter what, I can't get it to work. Any ideas? When I start the machine, select any program and close the door after a short while the machine does not complete the wash cycle and I get the following message either: E1 or E2 will appear in the control panel Any suggestions Dave M


I had this problem and fixed it tonight. When selecting a program water pumps into the machine, but with no drain i ended up with too much water and error code E6.\015\012\015\012I traced the fault to a broken wire between the electronic ... Smeg DWI614 Built-in Dishwasher

How to get to the control panel


Bosh is very tricky. You will probably have to remove the outer door panel first. #15 Torx screws all around the inside of the door panel. Support the panel with your feet while you remove the bottom two screws. (Do those last!) Close the door. Then ... Bosch 24 in. SHU43 Built-in Dishwasher

Control Panel Gets Stuck!


... Siemens 24 in. SE26293 Free-Standing Dishwasher

Kitchenaid d/w kude20fxss4 control panel won't light or respond. door light is blue, blinks 60 times. how do i get the dw to run?


... KitchenAid KUDE20FXSS Dishwasher

I have a DU1145XTP. The lock light button is on and can't get the dishwasher to start. I pulled the top panel and removed the cover on the switch and control panel.


\015\012To turn on Lock:\015\012Press and hold Heat Dry for at least 4 seconds. The Locked light\015\012glows. If you press any pad while your dishwasher is locked, the\015\012light flashes 3 times.\015\0 ... Whirlpool 24 in. DU1148XTP Built-in Dishwasher

Mod# mdb7601aww.... When I press cycle key, say heavy duty, then close door the 2H light flashes. I press the start button and the unit will not start. I have shut it down electricly and get the same results. what can be the problem? The front panel with the start/delay buttons or the inside control panel? I like to figure this on out the first time because each of those parts are $100+.


... Maytag Dishwashers

My Maytag MDB9150AWS is no longer working due to what I believe is a electrical fire in the front control panel as there was smoke coming out of the top of the front panel. There were no flames but the smell took your breath away. We had to open the Kitchen windows and door for several hours to try to get rid of the smell, but you can still smell it by the dishwasher. This model is not part of the recall. Has anyone else had a similar problem with this model?


My dishwasher (same make and model) had a similar problem except I did see some sparks coming out from th front on the side of it (on Thanksgiving Day no less - a lot of manual diswahing followed). What the problem ultimatly was is what I believe to ... Dishwashers

Normal, light rinse and cancel button are blinking. Turned breaker on and off with no change. Took panel off and tech sheet to give the codes was not there so don't have it. Repairman with no tech sheet says need new control panel. Is there any way to get the tech sheet online to reset and see if problem persists. Kitchenaid kudu02fr The unit is 4 years old.


... KitchenAid 24 in. KUDU02FR Built-in Dishwasher

KUDP01ILBS6 Kitchenaid dishwasher Doesn't work, except flashing lights on front panel. I have the normal light flashing. When I push any other button the cancel light starts blinking as well. I replaced the fuse, the main control board inside and it still doesn't work. Push button panel next fix? This is getting expensive. Could it be something minor? The troubleshooting papers didn't provide much guidance.


The first thing I would check is if the dishwasher is properly connected\015\012 to power input. There is a junction box under the dishwasher. To get \015\012access to it you have to remove the bottom panel. The power cord should \015\012be connected ... Dishwashers

MDBH945AWW maytag dishwasher panel lights will not light up. checked breaker and was not tripped. Hardwired circuit. will check tomorrow to be sure power gets to dishwasher. Suspect have panel control failure. In which case should I box it up for the local dump.


These control boards do not have fuses on them. I opened mine up when the front panel touch pad stopped working and the LED indicators were anemic. This is a sign of the ribbon cable connections have oxidized. The ribbon cable connects the touch p ... Maytag MDBH945AWW / MDBH945AWQ / MDBH945AWB Built-in Dishwasher

How do I replace electronic control board (how do I get to it)? (Several button panels hard to use, getting worse.)


Go to "Appliance Parts Pro's" they'll have the board and techs to help youD.I.Y. ... KitchenAid KUDR01TJ Dishwasher

Our GU2500XTPQ6 Gold quiet partner III begins a cleaning cycle but then different numbers appear on the minute countdown and the cycle never finishes. Once it gets to this point, you can only get it to drain. You cannot reset the cycle. We were once given a series of buttons to push to reset the control panel but don't know where it is. Can you help?


Yes call the manufacturer and ask for the code again ... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0946 seconds