Having problems with your Bosch 24 in. SHU43 Built-in Dishwasher ?

Have a shu 4322 dishwasher it fills with water and drains but the spray arms do not spray. have not tried anything yet.this dishwasher is not hooked up. it was given to me by a friend who replaced all his appliances.he also told me that the circuit board was recently replaced as part of a bosch recall. have you heard that there was a recall?


Answers :

Hello,
\015\012
\015\012Welcome to FixYa.
\015\012
\015\012
\015\012There was indeed a recall involving the control replacement nearly two years ago now if I recall.
\015\012
\015\012As for checking into the present issue ( it doesn`t sound like anything to do with the control based on your description ) it sounds like the pump impeller may have become stuck. Did the dishwasher sit idle or in storage unused for a period of time ?
\015\012
\015\012I have a service bulletin I could send you via email regarding remedying that issue of stuck impeller if you contact me at [email protected]
\015\012
\015\012I`d suggest you run the dishwasher through a diagnostic, but either procedure will require hooking it up.
\015\012
\015\012To do this test/diagnostic on the SHU4322 series machine, it is as follows...
\015\012
\015\012To start test program, press and hold both REGULAR WASH and RINSE & HOLD program buttons, then turn unit on by pressing ON/OFF button. Initially, control module version # will be displayed (e.g./ "20" = version 0 without jumper).
\015\012
\015\012When wash program buttons are released, lights above them will flash. To end test program, press ON/OFF button.
\015\012To check each program indicator light, press its button. To check Cycle Countdown display, Refill Rinse Agent light and REGULAR WASH light, press REGULAR WASH button (press Delay Start button to test Cycle Countdown display alone).
\015\012
\015\012Cycle Countdown display will show "88" when REGULAR WASH button is pressed and "8h" when Delay Start button is pressed.
\015\012To start testing, press both the REGULAR WASH and RINSE & HOLD buttons a second time.
\015\012
\015\012When testing has ended, Cycle Countdown display will show a fault using codes below. If more than one fault occurs, code numbers will be added together, (e.g./ "6" = faults 2 + 4).
0 = No faults detected 2 = Heating fault 8 = NTC (temperature sensor) fault 1 = Aqua Sensor ("Sensotronic") fault 4 = Filling fault F = Filling fault (display occurs during wash, not test)
\015\012
\015\0120 = No faults detected
\015\0121 = Aqua Sensor ("Sensotronic") fault
\015\0122 = Heating fault
\015\0124 = Filling fault
\015\0128 = NTC (temperature sensor) fault
\015\012F = Filling fault (display occurs during wash, not test)
\015\012
\015\012
\015\012
To check for heater, high limit or flow switch problems, start testing until heating starts. Using a meter with a current coil, measure current going into dishwasher. If current is ~ 11 A, then heater, high limit and flow switch are OK. If current stays at ~ 1.5-2 A, then heater, high limit or flow switch are faulty.
\015\012
\015\012i.e.
\015\012
\015\01286c0a8d.jpg\015\012
\015\012
If water level switch has failed (opened), display will show fault code "4" and unit will continually fill and drain where testing won't be completed. If flow switch has failed (opened), display will show "0", water won't heat (to 150?F) and water won't stop circulating. If NTC probe has failed (opened), display will show fault code "8" immediately and testing will end shortly after water has started circulating.
\015\012
\015\012
\015\012What needs to be done to solve the problem will depend on the results/findings of the dianostic, so let me know what you find and we can go from there.
\015\012
\015\012Either way keep me in the loop and I`ll assist you the best I can. Thank you for choosing FixYa and good luck.
\015\012
\015\012Regards,
\015\012
\015\012Macmarkus :)
Repair Help & Product Troubleshooting for Bosch 24 in. SHU43 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Have a shu 4322 dishwasher it fills with water and drains but the spray arms do not spray. have not tried anything yet.this dishwasher is not hooked up. it was given to me by a friend who replaced all his appliances.he also told me that the circuit board was recently replaced as part of a bosch recall. have you heard that there was a recall?


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012\015\012There was indeed a recall involving the control replacement nearly two years ago now if I recall.\015\012\015\012As for checking int ... Bosch 24 in. SHU43 Built-in Dishwasher

I have a Smeg dishwasher SA660 EB. Still like new . Hardley used but have problems with the timer switch not progressing past 5 and also had the thermostat replaced as a loud bang heard and the machine did not work. Since warranty on repair run out it sounds like water is leaking around the thermostat through onto electrics as loud bang noise heard again . I found the thermostat just pushes up into the rubber seal in the bottom of the dishwasher. I have taken out the rubber seal as this also loo


... Smeg Dishwashers

My dishwasher spray arms were clogged with calcium buildup so I cleaned one and replaced the other. I also removed the fixed disc-shaped device underneath the lower spray arm and found the particle filter was clogged- so I cleaned it out. The dishwasher ran fine for a few times but then the filter clogged again, and again, and again. Now I need to make a routine of disassembling the parts to get at the filter every week because the filter no longer clears itself during the wash and/or emptying c


You may want to check your hot water tank. It may need drained and cleaned, Or you may have the rod in the tank disintegrating. Also check you water faucet areators to see if they have calcium pieces too. ... Maytag Dishwashers

Hey Everyone! Ok try this one! I have been working on a KUDS25 Kitchenaid Dishwasher. It was leaking like a siv from the bottom. I replaced both top and bottom plastic bearings and also tightend all the screws at the bottom. Leak Gone, I thought. It now has small leaks down both sides. I have since been told by the owner that he took the door apart himself. I pulled out the dishwasher from the cabinet and ran it. I could see the leaks at the top on both sides of the door latch. I cou


Hello davidgalb. You can install a new gasket to seal the door again. That old seal is not flexible any more. That said, for my time and money I recommend a replacement dishwasher, this one has definitely seen better days. Joe ... Dishwashers

Last nigh my Maytag dishwasher model # MDB7100Aww serial # 15666931YM caught fire. Luckily I heard it and was able to put the fire out before my house caught fire. Has there been a recall on this model and how can I get a replacement?


Hi,\015\012\015\012Yes, there was a product recall for your Dishwasher due to fire hazard. Please visit the following pages for further information:\015\012\015\012 ... Dishwashers

I have a Bosch SHU9955UC/14 dishwasher. I am having problems with the top rack not cleaning. The dishes on the bottom rack are cleaning just fine. I have taken the rotating spray arm off and cleaned it out and replaced it. I have also taken all of the filters out of the bottom of the unit and cleaned them. Any other suggestions for fixing this problem?


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Bosch SHU9955UC Built-in Dishwasher

Maytag HDB8600AWW Dishwasher had been making noise (thought might be water valve, like previous DW), eventually stopped draining water, water now in bottom, I've let sit for couple weeks, looked inside, water was gone, I tried running again, it filled with water, but heard humming control panel noises for first time, then shuts itself off. Also, my handle needs replaced. Please let me know as soon as possible. Thanks in advance. David Weaver


Hi David\015\012\015\012The hum and all the noise that you have mentioned in your post states that the issue is with the pump and motor assembly. Please check the drain hose and try to clean the drain pump filter for any clogs, obstructions. Af ... Dishwashers

I have a De Dietrich DV640JE1 built in 45cm Dishwasher, working fine for over 3 years. After replacing the connection under the sink to fix a leak it has stopped working. But I dont think this is related. I run a cycle and it fills water in the bottom of the machine, it drains it out in the end but the 2 arms are not rotating and no water comes out. I checked the arms and they are not blocked. A faint clunking sound can be heard at some part of the cycle. I did also run a cycle with the dr


Hello Benny,\015\012\015\012It's highly unlikely that replacing the connection under the sink is related to this problem.\015\012\015\012From the symptoms you describe, it's almost certain that the circulation pump motor has f ... Dishwashers

KUD102CRWH1 The dishwasher does not start after a cycle. I have to reset the breaker in order to get it to run. The green led light flashes twice when I press start and I also replace the thermal fuse. Any assistance would be greatly appreciated. Unit is approximately 4 years old and not sure if there are any recalls on this. Thanks


... KitchenAid Dishwashers

The lower spray arm came off during a dishwasher cycle and melted. The dishwasher is okay but I need a replacement spray arm for a Sears Galaxy dishwasher model number 587.15139400 I have searched google for replacement parts for this model and have not found a place where I can get a lower spray arm. Any help would be appreciated.


Sears parts dept ... Sears 24 in. 14181 Built-in Dishwasher

Leaking This is a problem that I have when the dishwasher is in drying mode. I will find a 5X5 and sometimes smaller, size water spot under the dishwasher after the dishwasher has stopped. I was told it was the vent were the steam comes out and I had that replaced. It still leaks, then they told me to replace the rubber around the door, still leaks now they order a whole new plastic interior door. Please if you have any ideas what could be causing the problem, please let me know. Thank you


\015\012open the bottom panel 2-4 screw\015\012take a flashlight and turn the machine on\015\012see where it come from\015\012if you need take the unit out a bit f ... Jenn-Air JDB4000AWS Stainless Steel Dishwasher

I have a Hotpoint HDA3500N dishwasher and need to replace the base spray arm. I can not get it removed to put in the ge replacement spray arm model #WD22X10055. I'm afraid I'll break my dishwasher trying to remove the base spray arm


... GE Hotpoint HDA3500N Dishwasher

I have a Hotpoint HDA3500N dishwasher and need to replace the base spray arm. I can not get it removed to put in the GE replacement spray arm model #WD22X10055. I'm afraid I'll break my dishwasher trying to remove the base spray arm


... GE Hotpoint HDA3500N Dishwasher

Dishwasher 66513752K601 keeps blowing the thermal fuse. (Bi-Metal W10258275). I have replace the Thermal fuse several times. After i replace the fuse for some reason after a few months or less it will blow it out again. I have also replace the front panel assembly after it stopped working correctly. I would like to know how to test the dishwasher to find out the root cause of the fuse issue. I don't want to be replacing the fuse every time and don't have the $$ to buy a new dishwasher. Everythin


... Dishwashers

HOW TO REPLACE SPRAY ARM - Tappan Dishwasher Replacement Dishwasher Spray Arm 154567701


... Tappan Dishwasher Replacement Dishwasher Spray Arm 154567701

Dishwasher racks are falling apart from rust. I would like to replace them, but am confused as to what parts to buy. Also, do you know where to buy them? When I searched for replacements, it seems like by the time I finish buying all the replacement parts, I should just replace the entire dishwasher!


The racks are like 200 dollars a piece,replace the dish washer. ... Dishwashers

I am replacing a frigidaire dishwasher washmotor. Everyone and videos tell me how to replace the motor. In the instructions in the box they say replace the sump bottom also. Why would i have to replace the sump also and not just the new motor?


Hello, chris\012 \012 I was trying to help\012 you out here. I was going back to some customers that asked questions \012in the past and it appeared that no one answered them, so I thought I \012would take some ... Amana ADB1400AWB Dishwashers

On 2/18/09, I had a part replaced (due to a recent recall issue) on our Bosch dishwasher, SHU43C06UC. I had not had any problems with my dishwasher - ever - and, since the replacement, my dishes are not being properly cleaned. The Sears repairman who replaced the part tells me that the part he replaced has nothing to do with my present issue and, because my DW is no longer under warranty, I would have to pay for any further services he may provide. 1) What do I need to do to troubleshoot this di


Http://www.boschappliances.com/safetyrecall/dishwasher/default.aspx?pid=BCH0905OIQ001 ... Bosch 24 in. SHU43 Built-in Dishwasher

I have a Whirlpool dishwasher (Model #: du800cwdb5) and need help going about the repairs myself. When the dishwasher is turned on, the spray arm at the bottom does not spin, nor does it spray any water and the spray tower produces water but, rather than spraying, the water just kind of bubbles out of the top of the tower. The tower does also does not extend up as it supposed to.


There is something clogged in the motor/pump or its intake ... Dishwashers

We replaced our flooring a few years back with ceramic flooring which our floor approx. 3/4 inch. We now want to replace our dishwasher but find that the opening is now 335/8 and the standard height of a dishwasher is 34 inches . We also have a granite countertop. The tile floor does not extend underneath the current dishwasher. how can we install the new dishwasher???


Hi,Rather than Going for Different Adjustments,you could Buy a Dishwasher with Small Height. Bosch have so many Dishwasher's that could Actually Fit within those Dimensions without any problem.Even Hotpoint and Hoover have Mod ... Dishwashers

I have a kudso1flss6 dishwasher with the clean light flashing 7 times. Can I replace just the control unit or do I have to replace the heating element also? I also need to know how to replace the part or parts. Help!


Depress cancel button. Turn off power WHILE STILLL HOLDING DOWN cancel button, turn power back on. Viola! ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Dishwasher is model DWD1SSE type11045 Initially the dishwasher leaked water on the floor On investigation the bottom tray under the dishwasher was wet The motor was wet Tested the motor which was fine although the capacitor on the motor impellor was dead. Replaced capacitor, now no water going around the spray heads so found the impellor inside broken. Replaced that. No hoses are leaking. Machine now works fine heats up etc etc but over fills and the E5 fault shows


... Smeg 24 in. DWD1SSE-1 Built-in Dishwasher

My Bosch dishwasher Model SHE44C02UC just went completley dead while washing. My wife and I were in the living room and heard a ''pop'' and went to investigate. We discovered the dishwasher was completely dead with no lights on at all. The on/off switch does not work. I checked the breaker and it is okay. Also the disposal is also on this circuit and it still works so I know the circuit is okay. There is still water in the bottom of the dishwasher - no suds - so it may have been in a rinse cycle


Well done on confirming that the outlet is not the problem. This problem will not be able to fixed by the owner and a service call is the next step. (unless you want to dig into the problem, which could easily be a failed pump motor which took out t ... Bosch Dishwashers

My dishwasher is not working properly, i have cleaned all the filters and spray arms, but still have food partials all over dishes. I did use a knife to hold down door latch so i could see what was happening when the dishwasher is working. Water does come out of the spray arms but they don't move and the dishwasher is empty, also now the latch won't catch since i used the knife.


Make sure the water temp is not too low. Make sure the pump is not clogged up with debris Check that hoses and spray arms are all clear. Remove spray arms and clean the holes in them. Make sure the shafts spins that the arms attach to. ... Bosch 24 in. SHE44C05UC Stainless Steel Built-in Dishwasher

Plastic Pieces We purchased our ASKO 1385 dishwasher 7-8 years ago. Over the years, I have found "small square, thin, pieces of gray plastic" inside. Where are these coming from? Also, we have replaced the drain pump 2 years ago and looks like we'll be replaced the main pump within the next few days as no water is going through. We are looking at paying big $$$ for that pump. Almost half as much as purchasing a new dishwasher. Is this a common problem?


Yes, I have the same problem and it is the upper bearing rack, not the pump impeller. The new bearing kit is $30.00 (another is available for $123.00-the same!!). ... Asko 1385 Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2323 seconds