Having problems with your Bosch 24 in. SHU43 Built-in Dishwasher ?

I have a Bosch SHX46A05UC14 dishwasher. The dishwasher is in a new home I just purchased. I tried to run the dishwasher on a normal cycle. However, when I push POWER and NORMAL CYCLE it makes a buzzing noise...and that's it. I opened the dishwasher and on the base of the dishwasher there was a screen that could be removed. I noticed that there was still some anti-freeze fluid in there (because the house was winterized). Could there be a simple solution to this problem?


Answers :

Repair Help & Product Troubleshooting for Bosch 24 in. SHU43 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Bosch SHX46A05UC14 dishwasher. The dishwasher is in a new home I just purchased. I tried to run the dishwasher on a normal cycle. However, when I push POWER and NORMAL CYCLE it makes a buzzing noise...and that's it. I opened the dishwasher and on the base of the dishwasher there was a screen that could be removed. I noticed that there was still some anti-freeze fluid in there (because the house was winterized). Could there be a simple solution to this problem?


... Bosch 24 in. SHU43 Built-in Dishwasher

Bosch dishwasher Over the weekend my drains backed up into the dishwasher. After cleaning the drains I ran the dishwasher 3 times. Under the screen there is still about an inch of water. I never noticed this before because I never removed the screen before. Can you tell me if this is normal or is there a problem with the dishwasher. The water in the little area below the screen is clean.


Its normal. its there to keep moisture around the rubber seals so they dont dry out. ... Dishwashers

My dishwasher will not drain after cycling. I have check the drain hose connected to the disposal. All is in good order the hose is not cinked and the air hole is unblocked. I have also checked the screen at the bottom of the dishwasher, there is no debris or blockage here either. I can run the dishwasher on normal, it cycles but I still have stagnat water left beneath the bottom rack. How do I check my pump to see if it is working or could it be a short of some kind? It is a Kenmore Quite


The problem is a solenoid under the unit. It is a small black cylinder that operates a valve to change from the wash cycle to the drain cycle. You can probably order a new one from Kenmore for pretty cheap. ... Kenmore 24 in. 15252 / 15254 / 15259 Built-in Dishwasher

My Inglis dishwasher (E71195), 13 years old, doesn't clean properly. There is a film on everything that is especially noticable on glassware. I have cleaned every filter and unclogged everything that I could think of. I tried different detergents; right now I am using the same stuff in the dishwasher as we use to clean the milking equipment in our dairybarn because it gives the best result. It still is not as it should be however, there is still something left on the bottom of the glasses. It is


... Dishwashers

I have a 7 yr old GE Tritron XL dishwasher that I rarely use. Last time I used it was almost 2 months ago. A week ago I noticed a horrible rotting stench coming from the inside. I poured 1 cup of vinegar in the base and let it sit overnight. Next morning I ran the dishwasher with detergent but no dishes. Odor still there. Checked bottom of dishwasher for food - nothing there (I prewash dishes before putting them into dishwasher). Added 2 cups of vinegar, ran dishwasher on hottest setting. Sti


... Tappan MDB531RF Dishwasher

Melted rubber gasket, black rubber residue inside dishwasher I had a problem with the latch not connecting and therefore could not turn on the dishwasher. After, two months with Sears repairmen, dishwasher still did not work. I noticed as I put my head into the dishwasher to check on a buildup of residue this black glue all over the inside. Repair man stated it was animal fat. After spending some time looking at the situation under the door and inside I determined it was the gasket. He o


That is because Sears highers nimrods. sorry for the honest answer but it is the truth. Just a tip any time you get a Sears tech in your home and the first thing they do is get on the phone with tech support it's a bad sign that they DO NOT KNOW WHAT ... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

My KichenAid KUDS011 has functioned well until this morning. When I push any of the buttons on the keypad, nothing happens. I noticed there is still water in the bottom of the dishwasher from the last dish washing. Also, I've heard there is a screen or similar part in the bottom of the dishwasher that needs to be cleaned occasionally. I haven't figured out how to remove the bottom center of the dishwasher to access this for cleaning.


If the drain or screen are clogged, the machine may no operate.Unscrew the the 2 long screws on bottom, remove the basket, there may be a flapper under the basket, For pics, see here: http://www.contractorssolutions.com/dishwashers. ... Dishwashers

I have a Whirpool DU1145XTPQA dishwasher... It has started "Not Draining the water" at the end of the cycle. Dishwasher is only 2-3 years old. I have completly disconnected it and have taken it to my garage so It could be tested in a more userfriendly envoronment... I have found no blockage of any line..... The screen in the dishwasher is completely cleen...yet , when you press drain, It drains at a very very slow rate. I have noticed a small 40 Watt pump (drain pump) that attaches to the mai


There is only one motor that drains the unit.it seems to me that the impellar wheel is not turning fast enough to do the job,you have eliminated all other possible cause with the exception of the main board.\015\012\015\012replace the dra ... Dishwashers

I have a kenmore dishwasher, model 587-1625. Noticing that are dishes didn't seem to be getting very clean. I removed the drain screen and cleaned, noticing a lot of hard water deposit. yet, it still drain. Now after cleaning it doesn't drain now what?


Check for a plugged air gap (on top of the sink) ... Kenmore Dishwashers

Dirty dishes the dishwasher sounds and appears to be operating normally but the dishes are not getting clean. now i've noticed dishwasher soap still in the dispenser after the washing cycle has been completed. I'm thinking maybe i have plugged water jets? Anyone have any suggestions? Thanks.


Plugged jets, possiblemore likely it is leftover food reminance left in the pump area. and on certain dishwashers it could be a swollen check valve, not allowing the evacuation of the used dirty water.does your soap dispenser open? ... Dishwashers

I have a whirlpool dishwasher model adp 5550 condenser. The dishes do not get clean. I have had a repair man out twice and he replaced the soap dispenser on Friday but it still doesn't work. I went to the store today and bought every cleaning things I could find for dishwashers and also started to investigate online myself. I took the arms off and cleaned them, I took the filter out and cleaned it, and then I noticed that the plastic bar that runs from the top, along the back and into the bottom


... Dishwashers

Dishlex Global 310 model. My dishwasher has water sitting on the bottom of it and it wont drain. I noticed it after I did a cycle of dirty dishes and the 'fast' light was flashing when I went to open it. Which shouldnt have been because it was on a normal wash. The water has been sitting at the bottom for 2 days now and still wont drain! I've taken out all the parts on the bottom which come out and cleaned them. Still no change however.


Just ran another cycle and it was fine ... Dishwashers

Close the Maytag dishwasher, cycle starts, but I noticed a leak! Dishwasher door can be opened by putting your fingers on the edge and pulling it open. Tried it again, door clicked, thought it was ok but still could open door with fingers. Emptied the washer, door locked. Put in a few dishes, same problem


Your problem appear to me like it come from your upper basket .\015\012pleas try 1st to ensure the basket goes inside\015\012untill the end it is important..\015\012 thank you ... GE Dishwashers

Water will not drain out of bottom of dishwasher.It will go through the whole cycle but will not drain. This is a Frigidaire model no.FDB510LCS3 Serial no.is:noth70219331.Pump hose was disconnected and drained completely,dishwasher was put through another cycle and still ended up with water puddled in the bottom!! Could this dishwasher be called a lemon??? Does the pump need replacing?? I have noticed on your website that many others are having the same problem.To me it appears that it may be sh


Check the input to the drain hose to make sure it is not blocked by something like a cherry pit.  That could cause the water to not drain fully. ... Frigidaire 24 in. FDB510LC Free-standing Dishwasher

Hi, I have an LG LDS4821 dishwasher and it appears to stop working properly. The dishes don't seem to be cleaned at all. It seems like the spray arms are not spraying the dishes as the dishes are still dry/dirty after a normal wash cycle. I did notice that the detergent was used during the wash, and a trail of white residue was at the bottom of the tub. I can hear water pumping into the dishwasher, but when I opened it during a wash cycle, there was a puddle of water at the bottom of the


Hi,\012\012\012\012\012I\012have an older dishwasher also and recently my wife also complained\012about it not cleaning right... so me being the man I am tried in vain\012to clean the things... Bought new ... LG LDS4821 24 in. Built-in Dishwasher

Like so many others, I am experiencing a problem with my GE dishwasher's smartdispense. I have ALWAYS used the SAME detergent(Cascade Complete)and still have the gumming-up issue. I noticed that the dishes were not getting clean and when I opened the smartdispense cover I could see that the detergent was gelled. Spent the better part of 2 hours trying to remove as much gunk out of the dispenser as I could with the help of a plumbers flexible plastic drain cleaning tool. This really angers me as


I had the same problem as you also using Cascade Complete. It turned to a wet solid and completely cloged up. I have spent 3 days cleaning it and now have it working again. I had to spoon out what I could, but the purge method still would not wash ... Dishwashers

KUDP01ILBS6 Kitchenaid dishwasher Doesn't work, except flashing lights on front panel. I have the normal light flashing. When I push any other button the cancel light starts blinking as well. I replaced the fuse, the main control board inside and it still doesn't work. Push button panel next fix? This is getting expensive. Could it be something minor? The troubleshooting papers didn't provide much guidance.


The first thing I would check is if the dishwasher is properly connected\015\012 to power input. There is a junction box under the dishwasher. To get \015\012access to it you have to remove the bottom panel. The power cord should \015\012be connected ... Dishwashers

Bosch dishwasher SHX46A05UC/40 is making noise when draining. I have cleaned the screen and hose back to the drain and removed all debris. So it seem to be the 'drain pump'. But replacing it - now that seem complex - is it? Looks like I would have to stand the DW on its head and remove the base and then replace the pump. Anyone know if I am on the right track? Could it be something else?


... Dishwashers

I have a KUDS02SR installed at my cottage and, after connecting it for the season, I noticed a bit of water shooting out the housing where the water enters the dishwashed. I removed and cleaned the plastic housing but it still happens. The cycle finishes normally and cleans the dishes but I'm not sure how to stop the splashback from the housing vents. Thanks for your help.


... KitchenAid 24 in. KUDS02SR Built-in Dishwasher

My Kenmore Elite model # 630.16302402 dishwasher isn't getting the dishes clean. A lot of food is still on the dishes after cleaning, especially inside the glasses. There is a white film on glasses and the inside of the appliance. I also just noticed that the upper arm isn't turning. There is about 1/2 cup of water standing in the drain area (not visible until removing the filter tray at the bottom of the appliance). Is this normal? The obvious problem is the upper arm but it seems like the rin


Hello, \015\012 \015\012 ... Dishwashers

I have a Superplus Hotpoint dishwasher model no.7822. After normal wash there is still water about an inch deep left at the base of the machine. What can the reason be?


Hi.\015\012The filter basket in the bottom could be blocked, but it is more likely the outlet hose having become full of foul smelling gunge.\015\012\015\012You could try filling the machine with very hot water and plenty of dishwas ... Dishwashers

GU940SCGZO: Dishwasher quit during normal cycle and will not drain. Tried running the drain cycle on the cancel/drain button. It makes noise like it's working, but the water is still there - about 2" or 3". Could it be a fuse?


Hi it is unlikely to be a fuse, more likely it is the pump, the outlet hose or the internal hoses are blocked.\015\012\015\012please use this website below to assist you in troubleshooting your issue.\015\012\015\012 ... Whirlpool Dishwashers

Detergent sticks in main wash compartment. We use cascade complete with bleach (hydroclean action). When this problem started, I switched to cascade complete (liquid) and still same thing happens. The dishwasher is only 3 1/2 yrs old. Have used cascade complete since day one. Only difference is that this one is the one with the bleach. Could this be the prob? We have noticed that it is thicker that just the cascade complete. But thought the liquid would of fixed that prob. Agh frustrated. We hav


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

MY DISHWASHER MODEL GHDA480N10WW LIGHTS ARE FLASHING ON THE NORMAL WASH AND THE HEATED DRY I OPENED THE DOOR IN THE MIDDLE OF THE DRYING CYCLES THE LIGHTS STARTED TO FLASH AND BEEP I UNPLUG IT TO SEE IF I COULD RESET IT AND IT STILL BEEPS AND FLASHS


... Dishwashers

I have Whirlpool Quiet Partner III dishwasher, Model number GU2400XTPS3, Serial number FS1820245. I recently had the thermal fuse replaced by an authorized service repair person. My problem is that the dishwasher stops mid-cycle. I noticed that when I try to clean it in the normal cycle, the dishwasher stops with about 46 or 47 minutes remaining, and the green light flashes continuously. I have pressed the Normal and Heated Dry buttons, as well as the Sani Dry and HEated dry buttons to reset the


... Whirlpool GU2400XTP Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1943 seconds