Having problems with your Bosch 24 in. SHU43 Built-in Dishwasher ?

I have a 1999 bosch SHU 4300 dishwasher given to me. It worked great for about two weeks. Now it takes for ever *3-4 hours* to complete a cycle (if it does). I have opened the door to see it filled with sudsy soap after this long. I have checked the hoses and they are not kinked. Once the cycle of cleaning is over, If I reset it manually, it will rinse the dishes and empty just fine. But I have to manually get the dishwasher to advance to the rinse and dry cycle every time now.


Answers :

Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works like new... However I have also foundthat if the heating element goes bad then that also can mess things up bad...So I would buy new spray arms, and also check out the heating element to makesure it is working... Here is a tip that will help you with the onlinebuying...\012
Dishwasher SprayArms not Spinning

How to Buy ApplianceParts Online

A bad heating element causes many problems in dishwashers...

Dishwasher Problems The HeatingElement not Working

DishwasherMaintenance\012DishwasherResidue and Film on Dishes\012

heatman101

Asker's Testimonial "explanation very clear. will give it a go and see howsimple it was. thanks Ronnie " - ronnieshomes
\012
\012;'\012;\012;';
Repair Help & Product Troubleshooting for Bosch 24 in. SHU43 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a 1999 bosch SHU 4300 dishwasher given to me. It worked great for about two weeks. Now it takes for ever *3-4 hours* to complete a cycle (if it does). I have opened the door to see it filled with sudsy soap after this long. I have checked the hoses and they are not kinked. Once the cycle of cleaning is over, If I reset it manually, it will rinse the dishes and empty just fine. But I have to manually get the dishwasher to advance to the rinse and dry cycle every time now.


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Bosch 24 in. SHU43 Built-in Dishwasher

I have a 13 month old (Thanks Sears warranty!) Kenmore Portable Dishwasher Model 665.17769. It drains poorly, taking 2-3 times after load is completed running thru the ''cancel/drain'' cycle to clean it out. It is not getting dishes clean either, presumambly because the dirty water isn't being flushed out at cycle end and instead of rinsing with fresh water, it's still screwing with the dirty water. Manual doesn't offer any advice except to see if the hose is kinked (it isn't). I made sure nothi


Hello Linda it sounds like you may have a piece of glass or some other hard material in your drain pump which is partially blocking the draining process. Remove the hose in the base of the machine, then unscrew the drain pump and physically examine ... Kenmore Dishwashers

Kenmore elite dishwasher runs until it is manually shut off by opening the door? My Kenmore Elite runs continuously until I manually drain (cancel) the cycle. Then I have to rewash with no soap to simulate the rinse and again manually drain (cancel) the cycle. This was a $650 dishwasher. I am not sure how to reset the controller or even trouble shoot for an error code. Any suggestions?


It appears your timer/main controller/CCU has failed in this instance.For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.I recommend both sites bec ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Dishwasher HED6612 - salt light came on - have now filled the salt up and light has gone off. since this has happened whatever programme I set it to once the pre-rinse has finished and the wash light comes on an alarm sounds and doesn;t finish the cycle. when the alarm sounded I have pressed the start/reset button for 10 seconds to see if it resets it. I requested a manual last week and not received a reply from yourselves. this machine is around a year old [no manual available] and has been


... Hoover HD95M Free-standing Dishwasher

It won't complete a full wash cycle keeps stopping part way through and low rinse aid, low salt lights flashing even though both are full ??? Pamphlet says this might also mean there is a kink in the inlet hose but that seems fine as well. Have had the dishwasher 3 weeks and it has completed about 4 cycles without stopping ???


Check water valve to see if it has something blocking water supply ... Dishwashers

How do you reset a GE quietpower 1 dishwasher, it will only let me run it in Rinse cycle, no wash cycle, no heayed dry. I need a manual to learn how to operate the control panel!


... GE Dishwashers

Hi! We just installed our LG LDF8812WW built in dishwasher. We ran our first cycle and after the wash cycle the dishwasher displayed error code OE. I read that it meant there is a problem with the drainage, and to check the hose if it is kinked. Well, the hose is not kinked and we have no idea why it would have a problem with the draining. We have the hose set up per the installation instructions. How can we check to for something clogged? Any suggestions?


I actually own an LG LDF8812 myself, except mine is stainless steel, not white. So be it. :-)\015\012\015\012Anyway, it sounds like you have just unboxed the unit and it is brand new, not just new to you. I am also ... LG LDF8812 Stainless Steel Built-in Dishwasher

We have just installed a brand new Fisher and paykel 2 drawer dishwasher and the top drawer is not emptying all the water after the final rinse cycle. We cannot see any kinks in the drainage hose....


\015\012Make the following checks:\015\012\015\012\015\012Determine whether the washer's power supply cord is plugged into a live power outlet. Unplug the power cord from the outlet, then plug a working electrical ite ... Dishwashers

Hi, I have a Siemens SE24A230GB/17 dishwasher and it is not completing the wash cycle (any selected). It appears to be stuck on the 'wash' part of the program. I have done the reset actions as advised in the User Manual and tried another program, without success. I have found that the possible causes could be the timer or thermostat. The estimated time remaining display counts down, but the program does not complete the wash and move onto rinse and dry. Any help or advice you can provide would


... Siemens Dishwashers

Leaking dishwasher i have an 8yr old hoover dishwasher & it leaks on the rinse cycle. It's coming from underneath on the left hand side as you look at it. I've checked the hoses & clips on hoses, which seem ok. It only leaks as the water is coming into the machine on the rinse cyle. Never any other time, not even when it's filling for the wash cycle!


If your dishwasher leaks, check these:Main tub sealDoor gasket or sealWater-inlet valveHosesMain tub sealNote… If the main motor of your dishwasher is mounted vertically, beneath the center bottom of the dis ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

In order to reset my dishwasher i was told to alternatively press the clean and rinse button. my dishwasher has no button that says clean, rinse, or clean and rinse. my button choices are as follows: Front: CANCEL and START/RESUME Cycles: HEAVY DUTY, NORMAL, LIGHT/CHINA, QUICK CLEANUP, or RINSE ONLY Options: PROSCRUB, HI-TEMP SCRUB, SANI RINSE, HEAT DRY/Lock symbol, 4 HOUR DELAY. Does anyone have the correct sequence for initiating the diagnostic cycle?


If you want to reset the computer in that dishwasher you can just unplug it for a half hour. if it is a built in just locate the fuse in the or breaker that the dishwasher is on and pull it for that length of time. ... KitchenAid 24 in. KUDS02FRSS Stainless Steel Built-in Dishwasher

I have a GE Profile Eterna series triton dishwasher. When it gets t rinse cycle, lights go out and it keeps rinsing. Buttons stop working and it won't stop or reset. If I unlatch door and wait for hours lights may come back and allow a reset. Run through 3 rinses only -fine. wash cycle does it again.


... GE Dishwashers

Dishwasher stuck on rinse cycle. Have three yo son who plays with buttons, but I've been unable to get washer to finish (rinse went for three hrs prior to me realizing it was still running). Tried the front panel buttons w/o effect other than able to turn unit off, but it resumes in rinse cycle. Turned power off to machine from circuit breaker ( w/ machine off) then restarted and still in rinse cycle. How do I reset?


... Miele G892SC SS Dishwasher

KUDU03STSS2 The dishwasher won't start and you cannot select a cycle. Hiting cancel twice will turn a small steady light on in the time window were the spining light normally is before a cycle starts, at which time closing the door will drain the dishwasher. Tried using the reset combos: hot wash, heat dry, hot wash, heat dry - all lights came on but nothing reset. Also tried same sequence doubling the heat dry. Unpluged for ten minutes, still nothing. Can select rinse, but unit does not start,


... KitchenAid Dishwashers

My G832SC is not draining at the end of the cycle. It runs the entire cycle, and the dishes appear to be clean. The soap dispenser has opened and the dishes are rinsed. However, the dry cycle doesn't run because the machine doesn't drain at the end. The intake/drain light is flashing. If I reset the machine and start a new cycle, it will perform an initial drain and the water level does go down. We checked the tri-filter and the valve pump thing, rinsed both. Checked the hose under the sink. We


... Miele Slimline G832SCi Built-in Dishwasher

Westoint Dishwasher I have looked in the manual under troubleshooting tips, but didn't find anything on the problem. The dishwasher goes into cycle,but during the wash cycle it stops,makes alarm and the wash and rinse ligts come on. And now I can't even find the product on this site.Westpoint Dishwasher WQP12-9240. Thankyou My dishwasher is stopping at stage 2 of the programme after beeping once. Quite often the detergent flap doesn't open. Am at my wits end and threatening to leave home!!!! Th


Hi again,\015\012\015\012That should be OK. Just get in touch with your sales rep or his boss. Somebody there will be able to look up the record of the purchase. If they ask for model & serial numbers, you have them. You will find ... Dishwashers

I have a maytag quiet series 300. When it is done with any of the cycles in leaves about 1-2 inches of water in the bottom of the dishwasher. I can manually hit the start button twice and it will go through a 2 minute cycle and pump out the water. I have cleaned the filter inside the dishwasher where it drains and have checked the hose to the disposal and it pumps out fine. It just doen't pump itself at the end of the cycle. HELP!


Here it is - Maytag Quiet Series 300 Manual ... Maytag Dishwashers

I have a candy trio 501 dishwasher with intergrated oven. When I put a cycle on it starts its first rinse then after 5/10 mins stops and beeps constantly. It's still full of water too. When I put it on rinse cycle it compleates the cycle so inlet and drainage should be ok. Ive removed drain pipe and made sure its not kinked and also clear. I've removed and drained the compartments that had water in and also blew down the pips to see if clear all ok. I've checked the heater element with meter and


... Dishwashers

Kenmore Dishwasher Model 665.11643300 Cycle will not run. Normal Wash light blinking Cancel light will also blink (but can be cancelled by holding button down) I tried shutting down the power and resetting at the breaker. I tried other buttons like Air Dry, etc to see if there was some sort of sequence Note* last cycle ran was rinse cycle many months ago - house has been vacant and dishwasher has not been in use.


I will look a bit further in detail about your dishwasher problem. I am assuming you have checked the inlet water tap to the dishwasher is turned on. ... Dishwashers

My Kenwood dishwasher KDW24FI/B has worked fine for approx 2 years. But now when I put my dishwasher on, the cycle never seems to end. After a few hours of running I opened the door to find the tablet hadn't dissolved but lots of steam coming out. I tried 2 more times and the same thing happened. The pump is working and everything seems ok. After reading the manual I have noticed the salt and rinse aid lights are iluminated. I have never put salt or rinse aid in since I had the dishwasher so thi


Lol is it a stereo or a kenmore, dishwashers dont use salt, but water softeners do ... Dishwashers

Kenmore Elite - 9 Year old Dishwasher - A circuit blew and the dishwasher stopped in mid-cycle and did not drain.... I reset the circuit breaker and "manually" took the water out of the dishwasher. When I push buttons to restart the "95" shows up for the normal cycle. However, when I push start the "95" becomes a "--". Suggestions???


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Hello, my Hoover D7610 dishwasher has developed a problem, I would appreciate your advice.On starting a wash it appears to be working OK through what I believe to be a rinse cycle but then after about 20 minutes water pours out from the bottom of the door. Manually clicking the timer-programer forward stops the leaking but the machine needs manual advancement except for the last 2 cycles when the timer seems to work OK. After the 1st cycle there is no more water leaking from the machine but all


... Hoover Dishwashers

Kenmore 17369 When cycle starts... it sounds terrible (crackly sounding).... doesn't sound like the water is coming into the dishwasher. If I add water to the machine during a rinse cycle...it will wash and drain on its own.... Then I hit cancel. Please help.. I can't locate the owners manual.. Do you know where I can get one.. I understand that you can open the bottom up and see if there is anything lodged in the bottom of the dishwasher. Please help! thanks Cheryl


The problem is your water inlet valve. If you remove the panel at the bottom of the dishwasher you will see\015\012either a copper hard pipe, or a flexible steel hose leading into the\015\012water inlet valve.BE SURE TO CUT OF ... Kenmore 24 in. 17362 / 17364 / 17369 Built-in Dishwasher

The dishwasher did not finish last rinse cycle. I have no power, no lights light up. I reset the breaker. Is their another reset button on the Dishwasher itself. I have a Quiet3 Power GE Dishwahser.


Hi,I am sorry to hear regarding the trouble.The best way to reset - Disconnect the power supply for few minutes, say 15 minutes and then turn it on.If the problem persists, this would confirm an internal failure.As ... GE Dishwashers

I added 3 cups of water to the dishwasher DD24DT top drawer as directed to check the rinse cycle. I pushed the start/pause button, I hear some noise, but the dishwasher does not completely turn on., there is an icon with two arrows, like a cycle symbol. I did not get a manual with detailed instructions so need help!


... Fisher and Paykel DD24DT Builtin Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2267 seconds