Having problems with your Bosch 24 in. SHU43 Built-in Dishwasher ?

I have a Bosch dishwasher that just runs and runs and runs, it won't complete the cycle. Is there a reset button for now? And then, what?


Answers :

Hello,\015\012
\015\012It sounds like you have a control board issue.  You can try resetting the power to the dishwasher and see if that corrects the problem.  If not you may be looking at a board replacement.\015\012
\015\012Thanks,\015\012Bill
Repair Help & Product Troubleshooting for Bosch 24 in. SHU43 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Bosch dishwasher that just runs and runs and runs, it won't complete the cycle. Is there a reset button for now? And then, what?


Hello,\015\012\015\012It sounds like you have a control board issue.  You can try resetting the power to the dishwasher and see if that corrects the problem.  If not you may be looking at a board replacement.\015\012\015\012Than ... Bosch 24 in. SHU43 Built-in Dishwasher

I have a Kenmore Type 575-0 Dishwasher, model number 665.16033401, Style 16033. It runs trough the cycle, once the cycle is complete the clean mode light is on but most dishes are still dirty. I had someone here to repair this about a year ago. All he did was press alternating two buttons, which I have tried, it resets and lets you start a new cycle. However, the problem remains. Last time there was only button pressing involved, no need to replace anything. So, I would hate to have to pay ag


You need an electronic control and heating element ... Dishwashers

Bosch diswasher Turn dishwasher on lights that are showing are heavy duty wash, sanitize and clean lights. Just beeps like a load is completed - tried reset by holding down start button, etc.. Not able to even change cycles - only button that works is the on/off button


... Bosch SHX3AR75UC Ascenta Series 24 In. Stainless Steel Bar Handle Built-In Dishwasher

Bosch SHE43M was running when a pipe broke under the sink and flooded the kitchen. Water turned off before dishwasher. Now dishwasher makes a motor sound but no water starts and no cycles. Nothing happens when pushing buttons 3 & 5 to reset


Water is in the base and the float switch is activated. you must remove the water to deactivate.then hit the drain and cancell. let me tell you a quick joke .Im a old bosch tech and i had a call with the same problem. as soon as i got there i notice ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

When I press the start button, Bosch dishwasher (model SHY56A 05UC) just keep running the motor pumping the water out of dishwasher, irrespective of: 1) the wash cycle it is on, 2) whether the door is closed or open, 3) whether I cancel drain cycle, as told by Bosch Cust Svc in following steps: - "Cancel Drain" by pressing 'Quick Wash' and 'Regular Wash' buttons together for a minute until it shows 0* - Shut power off for a minute and wait for a minute - Restart on Quick Cycle. Paid


What is happenig i believe and has happened to me 2 times is that the water level float that is on the left side of dishwasher is stuck.\015\012\015\012Either remove side panel and flick lever or pull dishwasher out and tap lower portion ... Bosch SHY56A02 / SHY56A06 Built-in Dishwasher

Bosch shy66c drain motor keeps running after wash cycle is complete, can't reset using control panel or circuit breaker , pull dishwasher out and tilt it 45 degrees, there is same water on the flo


... Bosch 24 in. SHY66C05 Stainless Steel Built-in Dishwasher

I have a Kenmore elite ultrawash HE dishwasher Model 665.13129K700 , serial # FU3801153 , Stock # 13129K , Type 586-0. My normal wash red light flashed constantly and will not allow me to reset the control panel. I disconnect power for 1 hour then it allowed me to run 1 cycle. Upon completion the normal wash red light started flashing again. I tried to toggle between high temp wash and heated dry but no other button will work since normal wash is flashing. I again disconnected power but this tim


Hi,Push push thishi temp wash / heated dry hi temp wash / heated dry hi temp wash / heated dryIf this does not reset the control then you will need to replace the control board.Let me know,if needed fur ... Dishwashers

My Bosch dishwasher model SHE 4AM 16UC /03 is not washing correctly. All wash cycles ( regular/ quick etc) stop before completed There is dirty dishwater remaining in the tub. This happened also a couple of months ago, I can't remember exactly what I needed to do, but as I remember I needed to reset the unit, by pushing some of the buttons. please help


... Bosch Dishwashers

Bosch dishwasher SGS45EO2GB/45 does not complete washing cycle. It stays at 1 min left with pump running. I have reset the machine twice at which stage the pump empties the machine and the display shows 0 mins. However, have tried it agin and same problem. Any ideas, please?


... Dishwashers

Hi I have a problem with my Bosch SHU43CO6UC/22 dishwasher. using "power scrub plus" and "regular" cycles it will continue to fill and overflow the door, after the cycle has run even when the power button is off. I am using the quick wash cycle at the moment .After the cycle has run i open and check if the water has drained or not,If it has it does not continue to fill and flood.If there is water in the bottom after the cycle has finished it will keep rising untill I push the rinse hold button


The bosch dishwashers use a fill valve that is attatched to the inlet hose. yours is stuck in the open position. this usually happens when you have hard water, as the minerals build up on the sealing surface of the water valve. there is no easy ... Dishwashers

Kenmore Dishwasher Model 665.11643300 Cycle will not run. Normal Wash light blinking Cancel light will also blink (but can be cancelled by holding button down) I tried shutting down the power and resetting at the breaker. I tried other buttons like Air Dry, etc to see if there was some sort of sequence Note* last cycle ran was rinse cycle many months ago - house has been vacant and dishwasher has not been in use.


I will look a bit further in detail about your dishwasher problem. I am assuming you have checked the inlet water tap to the dishwasher is turned on. ... Dishwashers

Dishwasher stalls I have a Bosch dishwasher model # SHU4006UC/U06. The dial stops after going through one cycle and the dishwasher continues to run that cycle and will not advance unless we manually advance the dial. After advancing the dial the dishwasher will stall until we have manually advanced the dial until reaching the "9 o'clock" position. It will then continue until the dry cycle is complete. Thanks!! I have the same problem. I took out the timer control and spraid it with contact clean


If the cycle doesn't complete, check these:Water-heating cycle ... Bosch SHU4006 Dishwasher

Dishwasher stalls I have a Bosch dishwasher model # SHU4006UC/U06. The dial stops after going through one cycle and the dishwasher continues to run that cycle and will not advance unless we manually advance the dial. After advancing the dial the dishwasher will stall until we have manually advanced the dial until reaching the "9 o'clock" position. It will then continue until the dry cycle is complete. Thanks!!


The Timer might not be bad. If one of the two thermostats is bad, the Dishwasher will exibit the same symptom. The thermostats are 141 deg. F and 161 deg F.They only cost $20 each. The Control Module is close to $200. ... Bosch SHU4006 Dishwasher

Fisher paykel dishwasher dd601I runs complete normal cycle and finishes normally. 2-3 sec. after completion the washer motor srarts to run and the f1 fault (flood sw. activated) is dislayed. When the power button is pushed the fault spontaneously disappears and the motor stops. no moisture is in thre bottom under the tub and the normal cycle can be ru again with the same results.


Hi\015\012\015\012F1 code indicates an overfill condition which may cause when dishwasher can’t pump out dirty water due to a plugged drain hose.\015\012open dishwasher fully ,dry up as much water as possible the ... Dishwashers

We have a Blomberg dishwasher. We came to a finished cycle to find water in the bottom. We have removed the water by hand, cleaned the filter and the hose. The lights come on, but it doesn't respond when trying to run a cycle. It will do it's ''finished cycle beep sequence'' at the end of the cycle that it didn't actually run. We have reset it by holding down the start button. Turned it off and on, etc.


I am curious what the repair guy found. We have the same problem. ... Dishwashers

Bosch built in dishwasher shu4302uc The dishwasher appears to run through the cycle but the cycle takes over three hours. When the cycle finally finishes the dishes are not completely dry. Is there a way to adjust the timing for the cycles? I have checked the screens and they were clear.


\015\012There are no adjustments for cycle timing. What does affect timing is temperature of the water coming into the DW. The hotter your supply water, the shorter the time to cycle, BUT if your water is too hot, the cycle time may become too ... Bosch 24 in. SHU43 Built-in Dishwasher

Dishwasher is making noise likes it running and I haven't pushed any buttons. Cycle had said it was complete, I emptied dishwasher and when I closed door it sounded like it was running. I have tur


Hello seagraves98 - Since you have already confirmed that the spray arms are moving freely and the filter has recently been cleaned, I will suggest verifying that there is enough water pressure coming into the unit. Is the incoming water temperatu ... Frigidaire FGHD2433KF Builtin Dishwasher

Dishwasher stuck on rinse cycle. Have three yo son who plays with buttons, but I've been unable to get washer to finish (rinse went for three hrs prior to me realizing it was still running). Tried the front panel buttons w/o effect other than able to turn unit off, but it resumes in rinse cycle. Turned power off to machine from circuit breaker ( w/ machine off) then restarted and still in rinse cycle. How do I reset?


... Miele G892SC SS Dishwasher

I have a 1999 bosch SHU 4300 dishwasher given to me. It worked great for about two weeks. Now it takes for ever *3-4 hours* to complete a cycle (if it does). I have opened the door to see it filled with sudsy soap after this long. I have checked the hoses and they are not kinked. Once the cycle of cleaning is over, If I reset it manually, it will rinse the dishes and empty just fine. But I have to manually get the dishwasher to advance to the rinse and dry cycle every time now.


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... Bosch 24 in. SHU43 Built-in Dishwasher

My bosch dishwasher, one month old, has the active light flashing and the reset button won't reset it when I push it. A friend that was over opened the door when it was running because she can with hers, but ever since then, I had to take the water out and the active light is flashing and the wash light is lite. I hold the reset button for 5 seconds and then I shut it off for about 5 minutes, but when I turn it back on, the same things are happening


It sounds like the float is stuck. There is a float that stops the water from coming out when you open the door. It sounds like your friend stoped it in mid cycle and it jammed in the open position. Look on the inside of the machine for a plastic pie ... Bosch Dishwashers

Bosch dishwasher I have a month old Bosch dishwasher. It was stopped mid cycle. I drained the water at the bottom, but the active light keeps flashing, and when I press the start,reset button, then turn it off, it does the same thing when I turn it back on. active light keeps flashing and the wash light is on. It won't even lock the door. How do I fix this because there is no Bosch dealers here to help with the problem.


... Hotpoint 23 in. BF41 Built-in Dishwasher

I own a Bosch dishwasher that has operated perfectly for about ten years. The model is: SHU9915UC. Now it wont complete the cycle. The undissolved detergent is all over the dishes. After running 4 more complete cycles without any detergent the same undissolved powder detergent remains on the dishes. I have also executed a cancel/drain cycle. The filters are not clogged. I am great at repairing many tools and automotive "stuff" and don't want to call a repair facility. Please help.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I just read your previous post and I wouldn`t replace that timer/control just yet. There is a way to visually inspect the control.\015\012\015\012 ... Bosch 24 in. SHU53 Built-in Dishwasher

We have a Bosch SHE44C02UC/46 that suddenly won't start. I pushed the on/off button to start the dishes cleaning on the 'Power Scrub Plus' cycle and the display lights up with a 125 min. indication for the cleaning time, but the dishwasher never starts. It just sits there completely silent and never begins the cleaning. The dishwasher has worked perfectly up to, and including, the last cleaning cycle (3 days ago) for the last 4 years. Suddenly, today, nothing. Zip. Zilch. Nada. I don't get i


Hi.Re:" I\\'m sure it has to be something simple." A: yes, probably a fault, simple as that.To start there is a recall concerning this model. ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

I have a Bosch SHV55M03GB model which does not complete the cycle - if left it would run endlessly. However if set to rinse it completes the cycle after resetting the machine. I have checked the control module and there is no obvious damage or blueing/dry joints. any ideas - tempted to order a new module but want to ensure that i have exhausted all fault finding routes.


I do belive that the moduel is bad /. when you reset or go to rinse that is a different cycle and si sounds like the main wash cycle does not adv . you need to ck the heater & the thermo befor replaceing ... Bosch 24 in. SHV55M03GB Built-In Dishwasher

My power button cover broke on the dishwasher and I figured out the part number I needed, but when I put it back together I got the wires crossed on the board and door switch. Now the control lights up , but the dishwasher will not run a cycle. THe question is does the plug on the door switch have to be a certain way, because there are three wires and you can connect the plug both ways. I did turn the plug, but it still does not run. Did I break the switch? Bosch SHU9956uc/14


The wires do have to be a certain way on the door. Otherwise a door open can tell the board that's it shut and vice versa. The easiest way to do it, is test the switch with an ohmmeter, place the meter on the switch, push button in and see if the rea ... Bosch SHU9956 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2335 seconds