Having problems with your Bosch 24 in. SHU5305UC Built-in Dishwasher ?

Dishwasher repair My bosch dishwasher shu5305uc/u11 does not fill with water but the water valve appears to work.


Answers :

Make certain that there is water coming into the d/w if so and you are sure that the solenoid on the water valve energizes then its possible that the strainer on the water valve might be clogged if so its going to take a bit of work to remove and clean the strainer and reasemble it are you confident .
Repair Help & Product Troubleshooting for Bosch 24 in. SHU5305UC Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dishwasher repair My bosch dishwasher shu5305uc/u11 does not fill with water but the water valve appears to work.


Make certain that there is water coming into the d/w if so and you are sure that the solenoid on the water valve energizes then its possible that the strainer on the water valve might be clogged if so its going to take a bit of work to remove and cle ... Bosch 24 in. SHU5305UC Built-in Dishwasher

My dishwasher works except is does not appear to be getting water. David psr responded: Most likely the water valve is defective or stopped up with calcium deposits. In either event, you probably need to replace the water fill valve. Not a terribly expensive nor difficult job on most dishwashers. Do I call a plumber, appliance store repair department or look for a local handy man?


I agree that the fill valve may be bad or clogged. You can fairly easily remove the valve yourself if you are somewhat handy and then take it apart and clean it. I doubt if the old valve is electrically shot but it is possible. Cleaning it out may ... GE Dishwashers

Bosch SHU43C Dishwasher. Where to get parts - quick? Needs a new control-board / circuit board. All valves, switches, heater appear to work. Won't run open the water inlet valve. Won't run the self-check program. Has a burnt connection on the control 'mother-board'.


1-800-944-2904 That is Bosch Company. They will send out-- next day. ... Bosch 24 in. SHU43 Built-in Dishwasher

My dishwasher is only 2 years old. My small coffee shop is in an area where we have large quantities of lime. At this point in time the repair people have been out two times and this is not fixed. There appears to be no water being pumped into the dishwasher where it will be heated prior to washing. Also the temp gauge is not working all the time. With no water entering, the small amount of water in there is rising in temperature quickly if the gauge is working. The technician that have be


... Champion Dishwashers

Bosch SHY66C My Bosch dishwasher won't fill with water.  All electrical connections are fine and I can hear it make a sound as if it is trying to start about every 2 minutes.  There was water in the bottom so I used a shop vac and pulled it all out but it still won't start and is doing the same thing.  I checked the solenoid with a multi-meter and it appears to be working.  My power went out last night for about two hours and that's all I can think of that might have affected it.  The dishwasher


I'm a novice on this question, but i agree with the above statement about check the stuck float switch or check for a bad safety switch or lockout switch of some sort. I would suspect something is definately faulty in that area. Will the dishwasher r ... Dishwashers

How do I replace the water inlet valve on a Bosch dishwasher? I have done this on other dishwashers, but the rear of the Bosch valve appears inaccessible.


The easiest way I found to replace the valve is to pull the dishwasher out of opening and lay it on its back. When it is on its back you can get at the valve no problem. ... Bosch 24 in. SHU53 Built-in Dishwasher

My dishwasher was recently 'installed'. i don't know if the contractor made a mistake or if the water valve is not turned on, but the cycle tries to start but then no water is flowing into the dishwasher. everything appears to be hooked up, but I think it's the water issue b/c i also have a new refrigerator and the water dispenser/ice maker does not work because no water is flowing into the fridge either.


This sure sounds like a water valve issue, for sure. You will have to trace out the lines (not easy, but possible) and figure out where the valve is. They usually turn left to open, and right to close. I would call the contractor and tell them ... Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

Hi , My Bosch dishwasher SHX46A05UC/30 fills up with clean water after sitting a while. Ive read posts and think the problem is the water inlet valve . Where can i find the exact part number or Bosch repair manual on how to fix it.thx. Bosch have no tech support help


... Bosch 24 in. SHX46A05UC Built-In Dishwasher

My dishwasher after the cycle is over still have a bit of dirty water remaining on the bottom. After few hours is getting more and more dirty water. I have a feeling that some kind of the valve is not working correctly which allows the water from the sink drain to come back? Am I right? Is it a big re[pair or marginal? My dishwasher is about 20 + years old and still the greates one I owned ( I had before Bosh ). I own the dishwaser for last 4 years but previous owner loved it and never repair


Hello Ma'am/Sir,\012 The Best thing you're going to do is to have new Dishwasher.A lot of brand new products can help you, rather than striving the old one...Hope it will help you! God Bless you...Thank you! ... Miele Dishwashers

I have a GE Profile, GSD4930X73WW, dishwasher. The upper wash arm is not spraying well at all. I checked the water line from the pump to the upper arm and it's fine. I cleared the filters and cleaned the float. I also took the inlet valve off and cleaned the screen. Although the washer works better overall, the upper arm still does not work well. Nothing appears to be in the upper arm assy to clog water from spraying out. All seems clear from the turbid sensor (next to the pump) through t


... GE Dishwashers

HI MY DISHWASHER IS NOT WORKING.IT APPEARS THAT WATER IS NOT ENTERING THE MACHINE.THE ROTARY DIAL IS STILL WORKING AND IF I POUR WATER INTO THE MACHINE THE PUMP WORKS LIKE NORMAL.THE MACHINE IS A BOSCH SGS4072AU ,THANK YOU


... Bosch 24 in. SGS4072 Free-standing Dishwasher

Dishwasher Repair Dishwasher is a Stoves/Newhome DW616 Rotating spray arms do not always operate. This is an intermittent problem - will sometimes work normally for a few days then arms will not move at all with no water coming from them. Machine appears to go through its normal cycle. Some times cycle starts normaly and spray arms stop working part way through.


It could be a motor or a pump issue. The dishwasher has a motor that attached to a pump which forces the water up into the sprayer arms and during the drain cycle, it pushes the water out of the dishwasher. \015\012The motor (and pump) located beneat ... Dishwashers

I think I need to check the water pump/motor on my Bosch SHU43C dishwasher. It seems the water enters at the start of the wash cycle but then there is silence through the remainder of the cycles. Water will not spray. The drain appears to work ok to drain most of the water out. I have the washer out and upside down. Any hints on removing the base to get access to the pump? Should AI be looking at the control panel also for a fault? (the cycles seem to count down ok)


Click below;\015\012Latest Bosch Dishwasher Use and Care Manual\015\012\011\011\011\011May 4th, 2008 by Samurai Applian ... Bosch Dishwashers

I have a Frigidaire Dishwasher, model #FDB635rfs It is not that old, but appears to have quit working. It sounds like it runs the water gets pushed in by the tube on the side but goes straight to the bottom of the washer. It looks like the spray arms are not spinning. Water is not circulating. Element still heats up. Detergent just runs down the inside of the door and doesn't dissolve since water is not circulating through arms. I have just replaced the water inlet valve and it did not hel


Don't know about yours but many of the rotating spray-heads are turned only by waterpressure, not a separate motor.\015\012The rotator is normally pretty loose and should turn willingly by hand; if it seems stiff and your water pressure is normally l ... LG LDF6810 Built-in Dishwasher

Bosch slimline dishwasher SRS560. Unit has had this fault for a while, now going a bit mouldy so keen to repair it. Displays following Symptoms 1) Firstly empty motor drains water. This appears to be fine as I can hear the gurgling of the plug. 2) Then takes water from inlet to fill internal tank. I can hear the water entering the tank, and tap pressure indicates that water is being taken in. 3) The unit then sits there and does nothing for 25 mins until programme ends. I've


... Dishwashers

Frigidaire built in dishwasher model PLD2855RFC1. Have to wash dishes pretty much spotless prior to using dishwaser. Glasses come out with what appears to be soap residue regardless if powder or liquid. Did not use a gauge but water pressure in rest of house is good, recently replaced water heater, pressure regulator and just replaced the dish washer water source valve. Washer is about 18 months old, has never worked really well.


Hi, \012\012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms online and ins ... Frigidaire PLD2855RFC Dishwasher

Bosch SHE58C05UC/50 dishwasher stopped at 96 minutes (will not advance) & I cannot cancel. Diagnostic codes C4 then P0, rinse light steady on, drying light flashing. No water in anti-overflow pan, it's dry, float switch is working. Vacuumed out any/all water, Have replaced water inlet valve. Main circuit board shows no sign of solder joint disruption. Have switched circuit on, then off in attempt to reset (negative results). Any ideas on how to reset and then to fix the problem?


... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

Asko 3100 Dishwasher - when I press the Start/Stop button, all the lights on the cycle program button light up and the dishwasher motor starts up but no water appears in the machine. The dishwasher repair man guesses it is the valve or the computer but is not sure.


I am assuming you have the ASKO D3100 dishwasher.\015\012\015\012Can you please confirm which lights are flashing - is it one light on top of the program knob or all of them including the one on the Start/ Stop knob.\015\012\ ... Dishwashers

Bosch dishwasher (SXH55MO6UC/46): The power comes on and runs normal, but no water is coming into the unit. I was told that it was a water inlet valve that needs to be replaced (part #263833). I need to know if this is what needs to be replaced and if so, is this something that I can do or do I need an expert repair service to do it? If it is something that I can do, I need instructions. I am handy, but this is something that I have not done before, Thank you, Craig Covey


Hi Craig,Yes it may be the fill valve...but first take off the pipe or hose and check the screen just inside the fill valve...some do not have it but most do...also check that water comes out of the hose or pipe at the valve....THEN ... Bosch Integra® 500 SHX55M05UC Built-in Dishwasher

My Maytag dishwasher model MDB7130AWB started making a grinding noise tonight during drain cycle. We just had some work done on the sprinkler system and the water main to the house as well as the check valve for the sprinkler system have been turned off and on a lot the last two days. I noticed that we had some dirty water come out of a sink in a bathroom, after that repair. Don't know if that could be related to this problem but it was worth mentioning.


Shut off water to the machine, remove the hoses at the machine and inspect & clean the mesh filters in the water inlets. If dirt did get into the line, it would be from the water main work, not the sprinkler work.It doesn't hurt to clean the ... Maytag MDB7130 Dishwasher

I have a bosch she44c05uc dishwasher that get stuck on 1 and won't finish. The water will pump out when I cancel. The water will pump in but won't heat up. The final heating doesn't seem to work also. I have removed the circuit board and there appears to be NO solder issues. What else can it be?


... Bosch 24 in. SHE44C05UC Stainless Steel Built-in Dishwasher

We purchased an Electrolux Dishwasher Model #EWDW6505GBO, installed on 8/3/10, and we are very dissatisfied with it, as it just does not wash the dishes clean. We have had G.E. Dishwashers, two, since 1961, and then a Bosch, and they have all worked well. It appears that the water is not getting to the top and/or properly rinsing them. We rinse everything prior to putting the dishes in, but coffee cups come out with the ring around the top. The soap doesn't fully disolve. We have tried doub


... Electrolux Dishwashers

Dishwasher repair bosch dishwasher model no sgs5342gb/17 will not fill new water valve fitted


The most common reason why your machine has stopped filling is not the valve, but more likey you have had a leak and the base of the machine is full of water.\015\012If you take the lid off followed by the left side panel ( held on with 2 torx ... Dishwashers

Bosch SGS5312GB/12 Dishwasher I had a control board. Worked fine except didn't heat the water. Got it repaired (new PCB). Now the only thing it does is drain. Clicks every 20 secs and carries on draining. Got a new board. Does everything (including heat the water) except it does not drain before, between, or at the end of cycles. It does drain when while filling, and if the flood detection rod is raised manually (also drains if the inlet pipe beyond the pressure sensor is blocked - found


... Bosch Dishwashers

SHX46B I have a 4 year old Dishwasher that filled up with clean water on it's own and leaked on the floor. There appears to ba a float switch switch on the very bottom of the unit that runs the pump if this happens. It won't stop until I remove the water caught in the plastic base on the very bottom of the unit. Drain is clear and this machine has worked fine until now. I'm thinking it may be a bad or leaky fill valve but how can I check?


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2016 seconds