Having problems with your Bosch 24 in. SHU5305UC Built-in Dishwasher ?

Very long cycles,checked the hot water going in and its hot, but still very long cycle..


Answers :

Hello,\015\012\015\012The first thing which comes to mind is a very common occurance with B/S/H ( Bosch, Thermador, Gaggenau ) manufactured dishwashers, a failed solder on the control board, specifically the heater relay. Since the info you provided states your inlet water appears hot enough, I think it's not satisfying the thermistor for the control to advance correctly. It could also be a failed "ntc" the "heating element" itself or a stuck "flo-switch" in the heater assembly, but those aren't very common and therefore unlikely. With this in mind I'd first suggest calling in an authorized bosch servicer if that is an option for you and your budget however, If you cannot afford that option or feel capable of checking this on your own, there`s a way to visually inspect the control yourself ( and ultimately repair it, see "my opinion" below ) It will require you to remove the control from the unit and then remove the control from it`s plastic housing and look for a burnt solder contact on the printed circuit board. This will be one of the pins from the heater relay, hence the unit sit`s and takes forever to finish and eventually display's the "1" error ( on models with a display ) because it can`t heat to advance or unless the 2 buttons for "cancel" are pressed.\015\012\015\012**My Opinion - if you or someone you know is proficient at soldering, a lot of times it can be remedied by simply repairing the solder...but it has to be done well...or it will not last, although Bosch recommend`s replacing the control and I don`t pretend to speak on there behalf nor do I profess to know better. This is just my experience (it work`s) and my opinion (why buy new if one can repair ?)**\015\012\015\012**Please disconnect the power before attempting any service to the dishwasher. If you do not feel comfortable attempting this service, call a local pro, preferably one familiar with Bosch/Thermador/Gaggenau, to service your machine.**\015\012\015\012Hope this answer`s your question, let me know if I can assist you further. \015\012\015\012Thank`s for visiting "fixya" for your repair inquiries. Please take a moment and rate this solution to it's helpfulness.\015\012\015\012Good luck.\015\012\015\012macmarkus :)
Repair Help & Product Troubleshooting for Bosch 24 in. SHU5305UC Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Very long cycles,checked the hot water going in and its hot, but still very long cycle..


Hello,\015\012\015\012The first thing which comes to mind is a very common occurance with B/S/H ( Bosch, Thermador, Gaggenau ) manufactured dishwashers, a failed solder on the control board, specifically the heater relay. Since the info you provided ... Bosch 24 in. SHU5305UC Built-in Dishwasher

501ht goes thru wash cycle but cam stops just before rinse cycle clicks in - stays in wash cycle - turned thermostat to booster down in temp -cam then keeps going properly but with no hot water from booster - replaced thermosat still same result - apparently a safety ? no booster water no rinse?


Did you get a solution for this? I am having the same issue. Please email me at [email protected] Thanks -Eric ... Moyer Diebel 24 in. 501HT Built-in Dishwasher

KitchenAid KUDP01DLBS2 dishwasher. Runs for a very long time on any cycle; time does not seem to advance. (takes 2.5 hours or more for normal cycle. "sensing soak", "water heating" lights on for a long time, even though it appears that water is not being heated. Checked incoming water temp, is hot. Did not do this when new, something has changed. Typical cycle was 1 hr 10 min. before.


Sounds like the heater inside the dishwasher is not working. The machine is trying to get the water up to a preset temperature, probably in the neighborhood of 140 degrees. That is one of the things that it is sensing.After the machine fi ... Dishwashers

Our dishwasher (a Maytag - MDBH970AW) will not proceed past the intital intake of water. It has done this occasionally in the past, but with repeated attempts to start a wash cycle, it would eventually work and continue to work for some time afterward. However, in the past week, it will not go through a wash cycle. I have ran the water, prior to starting, to ensure that it is intaking very hot water. When it quits, I can push the start button again and it will go through the 2 minute drain c


... Maytag 24 in. MDBH970AW Built-in Dishwasher

ARISTON LSI 45/50 UK ALL COLD CYCLES ARE PERFECT ON HOT CYCLES IT GOES THROUGH ALL THE STAGES BUT NEVER ENDS THE CYCLES AND ALSO I THINK THE ELEMENT TEMPERATURE IS NOT BEING SENSED TO ALLOW HOT WASHES TO CONTINUE AND FINISH I ALREADY REPAIRED THE INITIAL FAULT WHICH WAS A RED 2 PIN CONNECTOR WITH A WHITE SOCKET GOING IN TO IT BOTH WITH 2 RED WIRES ON WHICH WAS VERY BADLY BURNED / CORRODED I REPLACED THIS WITH A 15 AMP CONNECTOR BLOCK BUT NOW I HAVE THE HOT WATER CYCLE FAULT


I tried to look up your model dishwasher ( aristion lsi 24/50uk ) by whirplool / can not find in data base / also you stated that all cold cycles work/ most d/w only use hot and there is no cold cycles . so there is always time to ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Dishwasher wont fill with water. just before it stopped filling i was turning the dial (a lot) between the wash cycles back and forth to attempt to get it to fill and drain (I didn't let it go through a cycle). We also removed the hose from the machine as it had split and replaced it and we had the machine tilted on it's side. the dial still clicks round but it sounds like the pump is going and it doesn't seem to be filling with water. Help


Hi. I suspect that the timer mechanism will be the culprit here, but i recommended to inspect and test the water inlet valve, before replacing the timer. The valve is a known problem area, as well. Follow the valve inspection procedure below, careful ... Fisher DS603W / DS603B / DS603I Dishwasher

I have a GE Potscrubber 720 and there is water in the bottom of the dishwasher and I tried to clear it by starting a cycle and it still keeps water in the bottom of the washer. When I run a cycle there is caked on soap on the inside door and dishes and the dishes are filthy. I found a long thin piece of metal by the drain it is long and straight and a break on one end and an "L" shaped bend on the other.. Any ideas where to start looking for problems? As I have no experience in repairing dishwas


... GE 24 in. GSD2600GBB Built-in Dishwasher

Kenmore Ultra Wash Quiet Guard - will not drain at end of cycle. After cycle is complete, water (not clean) sits at the bottom of the washer but I still unload the dishes and then turn the cycle dial around again - going past all the water heating and filling and washing - and land on the drain cycle, it will drain. Any ideas why it will not drain when I let a cycle run, but will drain once I cycle it through to the drain option?


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

There is gum stuck somewhere in my dishwasher drain line. The water won't go down. I took the inside apart and can see the hole where the drain water goes. I disconnected the drain hose under the sink. I got the water to drain out when there was alot in there, but now it won't drain again. I blew compressed air from a compressor backwards through the hose and it makes a big splash and bubbles inside the dishwasher, but the water still won't go down. I put Boiling hot water and vinager in there t


Ther e is noo easy fix, short of replacing the drain line( if indeed thats where the clog is)although you checked the hose from the under the sink, did you check with in the hole where the sink conection is made??and try disconnecting the drain hose ... Dishwashers

My trusty Bosch s510 Dishwasher which has been going strong for about 17 years (at least) has just decided not to empty itself. I noticed the bottom was full of water after a wash. I emptied all the water out by hand and presuming there is a blockage in the drain tried using a plunger to unblock it. I have since put it through another cycle and half way through water started leaking out of the front. At the end of the cycle the bottom of the dishwasher was again full of hot 'soapy' water. If th


Same problem, so went out and bought a new bosch. Problem with the S510 was cured by lubricating the pump out motor bearings with a squirt of WD 40. If you don't know which pump, follow outlet hose to pump outlet.Les ... Bosch Dishwashers

My dishwasher was moved for kitchen rennovations. When hooked back up again it would not fill up. It will run through a cycle but no water enters. If I squeeze the rubber hose that leads from the electronic valve to the tub it gets hot indicating that I am forcing hot water through the line. If I pour water into the tub it will wash the dishes but at the final 6 minute point it will go no further, I assume because it is not getting rinse water.


Hello,\015\012Make sure that a wire did not get bumped off of the soleniod valve. It sits usually on the bottom front left hand corner of the dishwasher.\015\012If the wires are both on the valve then the valve may need ot be replaced... ... Dishwashers

I got a whirlpool dish washer Adp4407. When the machine is switched on it carries out the cycles but seems that the hot water cycle is not working and the dishes are still unclean even after completin


... Dishwashers

Yes I have a whirlpool DU1345XTVB1 dishwasher. Just got in July. After each wash cycle the dishes are not dry. I have been using Finish gelpacs w/jetdry & also have a off brand drying agent in reservior to help dry dishes. The water temperature is set pretty hot & washer is draining good. I have tried checking wash cycle a few minutes into 1st cycle to see if water is in filling & heating. Didn't know if maybe heating element going out or thermostat not working? Thank you for your time.


<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-language: EN" lang="EN">Hi,<br />Check your heating element.. </span><br />\015\012<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-lang ... Whirlpool 24 in. DU1050SS Built-in Dishwasher

My bosch excel dishwasher has the following fault: start the cycle, water starts to fill but then check water light comes on and it then starts to empty again. Pump then keeps going. I have checked the hose and even swapped it round with my washing machine one but this makes no difference. I have cleaned all the filters and taken off the cover to check the 'propeller' as sugested in the instruction manual. But no joy - check water light still illuminated and willnot continue with cycle. - Help!!


This unit im sure has a water flowmeter that measures the water intake.. if this cannot read then the unit shuts down to avoid flooding.. \015\012it needs replacing... it is attached between the valve and the side tank or attached to the tank d ... Bosch Dishwashers

Candy CDI1012 Integrated dishwasher. When I turn on the dishwasher and start it - for some reason it can not go the whole way through the cycle. When I open the door the - programme light is flashing and water is still in the bottom of the dishwasher - ie mid cycle. The water will only drain if I put it into another program to drain away - but as the dishwasher was mid cycle - the dishes are not clean


Hello mm1973,It could be because of bad door latch switches / blown thermal fuse / blown or oversensitive control board. In all these scenarios, a dismantling of the machine is required. If you have no prior experience, I'd recommend get ... Dishwashers

Water will not drain out of bottom of dishwasher.It will go through the whole cycle but will not drain. This is a Frigidaire model no.FDB510LCS3 Serial no.is:noth70219331.Pump hose was disconnected and drained completely,dishwasher was put through another cycle and still ended up with water puddled in the bottom!! Could this dishwasher be called a lemon??? Does the pump need replacing?? I have noticed on your website that many others are having the same problem.To me it appears that it may be sh


Check the input to the drain hose to make sure it is not blocked by something like a cherry pit.  That could cause the water to not drain fully. ... Frigidaire 24 in. FDB510LC Free-standing Dishwasher

Half way through the wash cycle the motor seamed to still be working but no water was going through after i open the door mid cycle now i can start the machine but all the sounds are there but no water


U probably have a bad water valve under the dishwasher that is not opening properly if u have hard water that's probably what it is,it has lime scale in or on the valve ... Bosch Dishwashers

It appears to finish it's cycle, as far as the dishes are clean - however there is clean water that has pooled on the bottom. you can hear the water fresh coming in - the pump comes on for a few minutes, drains some of the water and shuts off - the pump comes on again - drains some of the water and turns off. I turned the water going into the dishwater off - the pump ran for a few minutes - drained some of the water and then just sits there with the red power light on - there is still the same


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Bosch 23 in. SHU3302UC Built-in Dishwasher

My 12 yr old KitchenAid -Sculptura-Model KUDR24SE starts to fills with water and then does nothing else. It will eventually go through the cycles on the panel, but nothing is happening inside. End result is still dirty dishes with water sitting in the bottom that has to be baled out. Cups on top rack don't have any water on the indentations, so it's obvious that the thing filled with water and that's it. I had the motor replaced (supposedly with a new) one 2 years ago so I find it hard to bel


... Dishwashers

Hello, Please help. I follow recommendations for cleaning: sewer pump, cleaning arms, screens of the dishwasher. However, still machine is not working. water is not going through arms: lower, middle or top. Also, I get water into dishwater when it starts, and when I open i hear noise for water dripping into hot elements,but no water is running throughout. PLEASE HELP


... KitchenAid 24 in. KUDP01IL Stainless Steel Free-standing Dishwasher

After starting the cycle, the dishwasher starts and runs normally for a short time, then the water drains out of the tub prematurely while the cycle is still going. The machine then runs dry until the cycle times out. At the next cycle and the process repeats. It started as a sporadic problem, but is getting worse.


You may have a faulty drain valve,the drain valve is under dishwasher there are two clips on each side check,with applance store for replacement part. ... Maytag 24 in. MDBH940AWS Built-in Dishwasher

I have a Bosch integrated dishwater that is just over 2 years old. It has suddenly stopped working and the tray at the bottom is not emptying, although you can still hear a buzzing sound. The cycle does not go beyond this point. I have emptied the tray of water and the dishwasher will start again, and pump water in, but it then stops, as though it is not able to pump water out. Does anyone know what this is? Could it be the pump? A blockage?


... Bosch 24 in. SHU43 Built-in Dishwasher

Our hot water supply to the kitchen sink became disconnected and flooded the kitchen. Since then it appears that we are not getting any water INTO the dishwaher (just makes a terrible grinding sound..solenoid stuck ?? ). I did put 3 or 4 quarts of water inand it drained alright. Also tried cancelling the cycles but that hasn't helped. We also discoonected the power for a day but still no luck. Please help Ron


... Bosch SHX55M02UC Built-in Dishwasher

LG 14AW3 just put a cleaner through it on a hot cycle. At the end of the cycle there is water in the bottom of the dishwasher and now when I try to get it to go through any cycle it just gives me a double beep. any ideas?


... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher

My Kenmore Elite Dishwasher (665.16499300) will not fill with water on the Normal Wash. It sounds like it's going through the cycle, but there's no water. I always run the hot water through the tap first. Oddly, the machine operates just fine in the Antibacterial Wash setting. Help would be greatly appreciated.


This machine is known to have a problem with the control panel. You need to get another one and replace the bad one that is in your machine. You should be able to contact sears and see about a replacement. You might even be able to get it done for y ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1774 seconds