Having problems with your Bosch 24 in. SHU53 Built-in Dishwasher ?

Washing cycle wont complete

\015 Regular Wash cycle counts down normally until the 1 minute mark. It stays there until the Cancel and Drain buttons are hit. Same thing with Scrub Wash cycle. Rinse and Hold Cycle appears to work normally.\015

Answers :

I had the same problem. Called the repair man, who said it was a defective control board. He ordered a new one, replaced it and now the problem is fixed.
Repair Help & Product Troubleshooting for Bosch 24 in. SHU53 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Heller HDW12 at first it wouldnt do a complete cycle, now it wont do any cycle. I can turn it on, it has power it just wont wash, it makes a noise but its not washing. The tap is turned on. Could you please help me as I live in Kalgoorlie and it takes weeks to get a plumber, and he's not cheap...probably cost me my first born!!!! regards B Hughes


... Dishwashers

My bosch sgv53e13gb dishwasher wont complete a wash cycle


... Bosch 24 in. SGV53E03 Built-In Dishwasher

I have a Whirlpool Quiet Partner 3 GU2200XTSB3 dishwasher that starts but wont complete a full wash cycle. I went to diag mode and the follow light sequence appeared: Normal light and washing light came on, then switched to Rinse only and drying then back to normal light washing this sequence repeated 3 times then no lights then Light and heated dry followed by the normal light flashing repeatedly for an long period of time then switched to Light and heated dry then all lights went out I was t


... Whirlpool GU2200XTSB GU2200XTSQ 24 in Builtin Dishwasher

Washing cycle wont complete


I had the same problem. Called the repair man, who said it was a defective control board. He ordered a new one, replaced it and now the problem is fixed. ... Bosch 24 in. SHU53 Built-in Dishwasher

I have a bosch dishwasher model # I believe is SHX4AP05UC it keeps tripping my braker in the middle of washing wont complete a cycle any suggestions?


Adam, in order to help you, you must provide me with more info. What size breaker is tripping. What does the maufactor's manual reads about what size circuit it must be plugged into. If your house is a little old you probably have a 10 amp breaker th ... Bosch Dishwashers

All Panel Lights Blinking wont complete wash cycle.


... Miele Advanta G2170SCVi Dishwasher

My Simpson Riviera 966 wont complete wash cycle,whats wrong with it ?


1) timer- it stays wherever you leave it and does that action.\015\0122) No fill -cold- for rinse\015\0123) No pump out\015\0124) Syphoning- where is your drain hose ?\015\0125) Set to " no spin" drip dry" -- reset control ... Dishwashers

KUDS30IXSS1 dishwasher will pump out water completely on the one hour wash cycle, leaves water in tank at end of all other cycles. Will completely drain when cancel/drain cycle is pushed. Is there a re-set code, or sequence; or is there a diagnostic code or sequence tohelp me? Like push Heat/dry, then normal wash, then Heat/dry, then normal wash within 6 or 7 secs? Or is my circuit board just shot?


... Dishwashers

I have a Kenmore Ultra 15895 or 15891. It fills with water then doesn't run. It will continue through it's cycles, but stays full of water. If I hit cancel before it completes the cycle, the number 2 shows in the display and nothing happens. If I let it complete the wash cycle, it will sometimes start and wash properly.


HI. The culprit will be the main control sector. This control fault may possibly be corrected by initiating a hard reset. the logic chips are scrambled, and this damage may be correctable by simply unplugging, or shutting off the appropriate circuit ... Dishwashers

Subject is Bosch dishwasher SHU6800. There is a soap residue left on dishes. Residue is not visible. Using two glasses taken from a recently completed wash cycle I rinsed one under tap water and then filled glass with tap water. The second was just filled with tap water. There is noticeable soap bubbling and foam in the second glass. Starting the 10 min rinse/hold cycle following completion of a full 60 min wash cycle results in considerble soap foam in the bottom of the tub. Have tried thr


WHAT IS WRONG WITH YOUR DISHWASHER? \015\012\015\012\015\012\015\012 \015\012For a detailed Dishwasher ill ... Dishwashers

My Maytag Dishwasher mdbd880awq wont finish a wash cycle. It will wash and rise then when there is 32 minutes left it wont drain and wont dry the dishes, It just makes a clicking sound. I have to dry the dishes by hand and then use the rise only cycle to get the tub to drain. The drain only doesn't work either


... Dishwashers

It does not complete the cycle. It stops working after 90 minutes without completing the cycle. Cycle should be 115 min. according to manual. Washing light is flashing but it does not continue washing. A huge amount of water remains in bottom.


... Haier HDC1804TW Dishwasher

Cant start the wash cycle on my kenmore precision quiet standard dishwasher my wash cycle blinks and wont start the wash cycle


... Dishwashers

My kleenmaid dishwasher super silent model system DW5 doesnt appear to be heating the water on any cycle so it is not washing properly and leaving the powder etc on the glasses up the top particularly and also it does not go completely to the end of the cycle by itself(any cycle).Or completing the drying cycle. I have to switch to 0 cycle to make it complete the clicking to start again. What is the gauge on the inside of the dishwasher on the left that can be adjusted from 1-5 is this a heat


Http://frigidaireservicetips.com/pdfs/486_5.pdf\015\012\015\012\015\012\015\012Service manual, generic, use this to troubleshoot and repair.\015\012\015\012 ... Dishwashers

Westinghouse Virtuoso 922 dishwasher. Wash cycle completes, but water does not drain out. If I let the cycle continue, after a delay the rinse cycle starts, but of course no clean water is pumped in so the dishes are "rinsed" in the dirty wash water. The wash cycle itself is successful with water pumping all around the washer if I open the door mid-cycle. I have removed and cleaned all filters which were correctly fitted so I am confident there is no foreign matter inside pump. When the water sh


... Dishwashers

Wash cycle, the pump cycles on and off does not continuously wash. The wash cycle will not complete and then the dishwasher turns off. I can restart another cycle immediately with the same result with varying run times.


... Maytag MDBH965AWS Stainless Steel Built-in Dishwasher

The dishwasher cycle starts and gets 20-30 minutes in and then stops giving me the - - - like the door was opened, but it was not. If I use extra heated wash, the cycle stops at 63 minutes left. If I use the regular wash cycle, it stops at 43 minutes left. I have to click the resume button to get the dishwasher to complete the wash cycle. This has been happening evey time I use the dishwasher the last 2 weeks. It is Whirlpool dishwasher model GU2700XTSS! and is only 3.5 years old.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I suspect based on your description...\015\012\015\012"stops giving me the - - - like the door was opened, but it was not, I have to click the res ... Whirlpool Dishwashers

Kenmore dishwasher My Kenmore dishwasher model 630.16302401 is not successfully completing wash cycle. When I hit "normal" and turn it on, water enters the d/w, and the sprayers (both top and bottom), spray water. Approx. 10 mins. later, the water is drained. At that point, it appears that water never again enters the d/w to complete the wash cycle. In fact, the soap in the dispenser does get released, and the door opens. However, the soap will just run down the inside of the door and pool on th


... Maytag Dishwashers

I have a GE Quiet Power 3 dishwasher and water is not draining completely after the wash cycle completes. There is about an inch of risidual water in the bottom of the washer after the wash cycle is done.


... General Electric Adora GHDA670N Built-in Dishwasher

Kenmore Ultra Wash Quiet Guard - will not drain at end of cycle. After cycle is complete, water (not clean) sits at the bottom of the washer but I still unload the dishes and then turn the cycle dial around again - going past all the water heating and filling and washing - and land on the drain cycle, it will drain. Any ideas why it will not drain when I let a cycle run, but will drain once I cycle it through to the drain option?


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

Kenmore elite dishwasher model 665.13153k701 At end of wash cycle, water does not drain completely. Intemediate drains during wash do drain completely. rinse and hold drains completely. watching water at end of wash thru disposal, water flow cuts off like valve closed. other drains taper off


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Glasses have a film after washing complete. No food particles, just heavy film. I suspect dishes are the same, but doesn't show as much. Water temperature entering washer is 130 degrees. Heating element heats during drying cycle---not sure during wash cycle. Sounds like a good water spray during washing cycle.


There are many probable causes of failure .A dishwasher's water inlet valve is its most common part to fail. When \015\012your dishes are not being fully cleaned, quite often a faulty ... Frigidaire 24 in. FDB421RF Built-in Dishwasher

I have a Sears Kenmore Elite Ultra dishwasher 665.1315 model. For the last 3 weeks, it keeps having the clean light blinking 6 times pause then 1 blink and pause and repeats cycle again. I have turned off the breaker...I have reset by pressing the heated dry and normal wash until all lights are flashing. It then completes some type of cycle and looks ok. When I opened the door, steam came out and all was hot inside. However, once I try any new wash cycle, it seems to wash but after 1-2 hours and


Call sears service and tell them you need service there is a service flash and will be no charge ... Kenmore 24 in. 15932 Built-in Dishwasher

I have a new Frigidaire FDB1050RE diswasher. I ran it for the first time set on normal wash and pressing both the Hi-temp wash and heat dry button. This cycle is supposed to take a total of 89 minutes to complete including the drying cycle. After 89 minutes it was still in the wash cycle so I cancelled it to preserve sanity. In the instruction manual it states that the water temperature must be above 120°F. Our building's water heating unit is set at 110°F. Why there is a lower temperature


It should still work pretty well but you probably can't use the high temp wash because it will take too long for the dishwasher to heat up the water enough to satisfy the high temp washer thermostat. If the thermostat's calibrated closing temperature ... Frigidaire Dishwashers

My Bosch SMU2000 series dishwasher will not complete the wash cycle. Advancing the dial completes the cycle but it sticks again before completing the rinse cycle. I replaced the timer assembly and the symptoms are the same


Hi,It seems to me a Faulty Control Board. You need to pull up the control board and check the resistors on it. If found burned or swelled, needs to replace those.Note - It's better to replace control board than to repair as yo ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1285 seconds