Having problems with your Bosch 24 in. SHU53 Built-in Dishwasher ?

Water keeps coming into the dishwasher. Had to shut the hot water shut-off to stop the water from continuously filling the unit. How can I make repair myself.


Answers :

Hello,

Welcome to FixYa.

Based on your description, " Water keeps coming into the dishwasher. Had to shut the hot water shut-off to stop the water from continuously filling the unit "...and to answer your question, the issue is likely with the inlet/water valve.

\015\012
\015\012**To remedy this you will need to replace the valve**

This is what to look for..i.e.

e601791.jpg

As long as your model number is indeed correct, this info below will be accurate.

Original part is # 425458. It usually retails for about $20 - $30USD at places such as "searspartsdirect.com" "repairclinic.com" to name a couple, if needed. They may be available at your local brick & mortar parts depot/vendors.

**Before attempting to repair the unit please turn off the power and the water supply to the dishwasher...safety first**


If you remove the lower kick plate/toe panel, you will see the inlet valve to your left...


i.e.

7d9ad1d.jpg

Replacing it or to check for debris in the filter/screen at the inlet is pretty straight forward. Here`s how...

1) undo the water line. ( here you can visually inspect the screen in the valve...if nothing noted, you'll likely need to replace it as follows )

2) Remove the two #20 torx screws fastening it in place.

156e176.jpg

3) the feed tube to the machine at the back of the valve and swap it with the new one.

5937279.jpg
and

dd52c6a.jpg
Once the new one is in or it's all clear you should be good to go.

Let me know if you need any further assistance, otherwise good luck.

Thanks for visiting FixYa.

Regards,


Macmarkus :)

Repair Help & Product Troubleshooting for Bosch 24 in. SHU53 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Water keeps coming into the dishwasher. Had to shut the hot water shut-off to stop the water from continuously filling the unit. How can I make repair myself.


Hello,Welcome to FixYa. ... Bosch 24 in. SHU53 Built-in Dishwasher

Smeg dishwasher model DI 612 C type 12053 good morning After selecting a program and shutting the door the drain pump starts and runs for 2 seconds then stops. The machine makes a bleep noise then the drain pump starts again running for 2 seconds then stops again and the cutting in and out process continues and the machine never reaches its selcted cycle. No alarm lights are displayed. I have filled the machine with water so that the filter is submerged and the level is


... Smeg Dishwashers

Maytag Dishwasher I would like to know the proper water level after DW fills. Older Whirlpool units a quick guide was when water just covered heater. I have a new D/W and the water supply is difficult to access, there is a kink in the water line slowing the water flow. The D/W fills to bottom of heater, but because the unit is so quiet I can't determine if it is timing out or working properly. I intend to repair water line when counter work is done. Thanks for any help Gary


Newer Maytags should fill close or up to the heater not over. Sounds like your alright for now but I would get that water line fixed. ... Maytag 24 in. MDB8951AWS Stainless Steel Built-in Dishwasher

Our GE dishwasher (5 yrs old, Model GLD4250L00CS) only fills with water half way when the unit is started. The inlet valve was replaced with a new one, but that did not solve the problem. When started, the dishwasher fill cycle runs for 41 seconds before the wash cycle begins. Repair workers told us we probably need a new ECU (Electronic Computer Unit). My questions are: Is 41 seconds the correct time for the fill cycle for our model? What else could be the reason for the unit not filling pr


Hello &\015\012Welcome to FixYa\015\012\015\012Check this\015\012 ... Dishwashers

Maytag Model MDB7160AWW S/N 10337613WQ Symptons: Fills with water OK, shuts off water OK, does not start any cycle, or drain. After a power off/power on reset, problem remains. Flashes CLEAN & LIGHT WASH. My understanding is this is an error condition for low motor current, which makes sense as the motor never starts. I know both door switches are good (I checked them with a DVM) and both engage when the door is closed. Tripping the water float switch opens the valve and water fills the tub


... Dishwashers

When dishwasher is turned on to the cycle mode - it fills with water - heater heats water to the proper temp - pump starts - washer goes through it's complete cycle - even pumping out the wash water and the drying cycle,then shuts down. the problem is that it does not circulate the wash water thru. the spray heads-even though the circ,pump is running.Even though the unit is 8 yrs.old and hasn't run for 6 yrs,my wife&i do our dishes by hand. our unit is a GU1200XTKB0 Serial# FL4617501


The impeller on the wash pump is worn out or the disposer screen is obstructed. Disassemble as needed to investigate the cause. ... Whirlpool 24 in. GU1200XT Built-in Dishwasher

Bosch slimline dishwasher SRS560. Unit has had this fault for a while, now going a bit mouldy so keen to repair it. Displays following Symptoms 1) Firstly empty motor drains water. This appears to be fine as I can hear the gurgling of the plug. 2) Then takes water from inlet to fill internal tank. I can hear the water entering the tank, and tap pressure indicates that water is being taken in. 3) The unit then sits there and does nothing for 25 mins until programme ends. I've


... Dishwashers

My Bosch SHY56A02 dishwasher won't fill....When cycle is started, it seems to pump water out but none in. Water feed is good....Added water manually and it pumps out immediately. Also, unit continues to run with door open...door switch is not jumpered. Could it be the fill valve? More likely the control module? Thanks for your help!


Hi,\015\012\015\012As water is filling in your dishwasher a float rises along with it. When the float reaches a predetermined level it shuts off the flow of water by activating a switch thereby preventing a leak. Sometimes the float can g ... Bosch Dishwashers

I have a Sears Kenmore Elite dishwasher Mod. # 665 - Ser.# FJ4805735 that intermittantly skips the wash cycle and pumps the hot water out just after filling. This unit was built in 2000 but the entire drive unit was replaced about 6 yrs. ago. If the problem lies in the electronics is it worth a do it yourself repair. I have an antique (1970'S) appliance repair background and electronics is not my forte. Money is tight and I would like to squeeeeeeeze another couple of years out of this appli


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012Would you be able to supply the complete model number. The Kenmore elite dishwashers where made by many different manufacturer's over the years, even within t ... Dishwashers

I just installed a Bosch shx43R55UC/64. Upon starting all lights are on and I cannot select a cycle. When I shut it the unit starts but will not fill with water. The float switch is working, No wat


U need to clean out the water chamber on the left hand side and the diofram too ... Bosch SHX43R55UC Dishwashers : Built in Dishwasher

Maytag MDBTT79AWW dishwasher fills and nothing else. Once filled you hear a click, followed by a humming sound for 3-5 seconds, then silence. This will happen two or three more times, and then unit will shut off. Motor doesn't start. Repairman says he thinks control board is bad, but he sounds like he is guessing. I performed a field service test , which indicated a fault in the high current motor circuit. Unit is seven years old. Don't know whether to attempt repair, or replace.


That sounds like the motor trying to start but being jammed it is shutting off via an internal breaker. Check for something in the bootom of dishwasher that might have gotten down there that could do this. You might have to take the sprayer off and s ... Dishwashers

Water coming out front of dw at start of wash cycle. I leveled the unit. no luck. if you open the door during fill cycle the water does not shut off. also, may be a problem with float shut off working properly. what should I try next? Kenmore Elite 16579


Hi \015\012Check float to insure that it is free to move, it sounds like the dishwasher is over filling. That is assumed that you have not changed the type or amount of detergent being used.Also there is a probability tha ... Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103

Dishwasher fills with hot water. Float OK - water feed stops when full. Motor humms but no water spray (in all opperating modes). Cancel selection (with cancel button) and close the door. The water drains then the unit shuts off. Water feed OK. Drain Cycle OK. Looks like spray pump hung but do not know. Cannot find a reset button (as with disposal) or way to free hung pump motor. I did see glass pieces in the drain. Possibly a small piece hanging the motor.


If you found broken glass inside the machine some has likely migrated to the pump. about the only way to fix that issue is to remove the pump and either replace it or disassemble it and clean it out. ... KitchenAid 24 in. KUDP01FL Built-in Dishwasher

Maytag HDB8600AWW Dishwasher had been making noise (thought might be water valve, like previous DW), eventually stopped draining water, water now in bottom, I've let sit for couple weeks, looked inside, water was gone, I tried running again, it filled with water, but heard humming control panel noises for first time, then shuts itself off. Also, my handle needs replaced. Please let me know as soon as possible. Thanks in advance. David Weaver


Hi David\015\012\015\012The hum and all the noise that you have mentioned in your post states that the issue is with the pump and motor assembly. Please check the drain hose and try to clean the drain pump filter for any clogs, obstructions. Af ... Dishwashers

Kenmore (Whirlpool) 655 1589910 Dishwasher. Fills with water, motor makes horrible noise (buzzing / loud hum). Dishes do not wash and there is no evidence that any water pumped up to the spray arms. Spray arms are not clogged. We have a fully functioning water softener so it is not a hard water issue. Unit does drain normally. Either filter is badly clogged or pump is bad. How do I get to these parts to check them out?


You need to clean/ check the chopper. sounds like you have a bad motor. about 2-300 dollars for the part ... Kenmore 15899 Built-in Dishwasher

Water won't stop filling my 9915uc unless I shut off the water supply. Unit drains, and then water floods back in (I mean floods--through kitchen floor into basement ceiling).


Either water valve is stuck open or fill switch assembly is not working ... Bosch SHU9915UC Dishwasher

My bosch excel dishwasher has the following fault: start the cycle, water starts to fill but then check water light comes on and it then starts to empty again. Pump then keeps going. I have checked the hose and even swapped it round with my washing machine one but this makes no difference. I have cleaned all the filters and taken off the cover to check the 'propeller' as sugested in the instruction manual. But no joy - check water light still illuminated and willnot continue with cycle. - Help!!


This unit im sure has a water flowmeter that measures the water intake.. if this cannot read then the unit shuts down to avoid flooding.. \015\012it needs replacing... it is attached between the valve and the side tank or attached to the tank d ... Bosch Dishwashers

During wash cycle water leak appears on the floor at the left side of the unit. this is a new unit model #Kuds301vwh #FO1114221 purchased and then installed on 3/25/10. Gasket was replaced on door by factory repair man and leak continues. unit appears to be level.Unit is covered under warrantee.


... KitchenAid KUDS30IV Builtin Dishwasher

I have a year old kitchen aid dishwasher and during fill cycle it makes a thumping noise. The dishwasher every 5 or 10 seconds shuts off fill cycle then turns back on which I think is what's causing the noise. Not sure but seems like water should run until fill cycle is complete?


Drain Pump\012 \012 \012 \012 \012 \012 \012 \012 \012 \012 If the dishwasher is loud dur ... Dishwashers

Indesit dishwasher dif 04, dishwasher fills with water then makes a very low grinding noise for approx 3 mins and then continues its cycle but doesn't wash, the water does get hot but no dishes are clean


... Dishwashers

I have a triton XL model GSD6900 that does not fill with water. I replaced the fill valve about 8 months ago. Have checked the inlet valve and coil shows continuity. Ran it thru a cycle and found no voltage at the valve. I assume the problem is in the timer. If this is the case should I have it repaired or buy a new dishwasher.


... GE 24 in. GSD6900J Built-in Dishwasher

I have a GE monogram zbd5900 that continues to drain, won't shut off. The drain pump just runs. None of the lights on the control panel will come on, tried pressing and holding buttons to clear, nothing. Turned off and on circuit breaker (even left it off overnight) and did not change. Drain is not blocked, pulled the unit out and put water in the bottom and it pumped the water out just fine. any thoughts?


See if you can access the tech sheet, should be on the right side of the underside of the unit after you remove the toe panel, or perhaps in the console. Almost sounds like a stuck key pad but the tech sheet might shed more information on this malf ... Dishwashers

My asko dishwasher ran great until recently. after finishing a load, the pump just continues to run (even when all water has been pumped from the unit and it's running dry) and the display isn't flashing anything (not codes, etc). Worried about destroying the pump, I shut off the washer at the breaker, and it's been a few months since we've had a dishwasher. Every once in a while I'll turn the power on and it just continues doing the same thing - it's stuck in this position/state, so I have to s


The IC that controls the pump seems to have gone kaput. Change the IC. ... Dishwashers

Frigidaire Dishwasher Will not fill with water, cheched water valve- no continuity and no 110 volts when the knob is turned to first position. The numbers that were on the valve are C-103/07, 33129014, 672050200016. This unit is in a RV.


Replace water valve. ... Whirlpool GU2400XTP Built-in Dishwasher

Dishwasher seems to slowly fill up with water when the unit is off. Seems as if the water valve doesnt shut off poperly.....what might be the problem?


Most likely the water valve is contaminated with calcium deposits, preventing the valve from seating properly.\015\012\015\012Possibly you could remove the water valve, remove the electrical coils and soak it in a household Calcium/Lime/R ... Bosch 24 in. SHX57C05UC Stainless Steel Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1770 seconds