Having problems with your Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher ?

Dishwasher/diplomat-adp8342 not draining,left standing for a few months and now programe panel wan't work,if i turn it off then press the panel a few lights will go on but nothing semms to work,


Answers :

Repair Help & Product Troubleshooting for Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Have a 4 year old Kenmore Dishwasher Model # 74382. No problems at all until last week I went to start it and it would not turn on. Lights on the control panel were on with exception to the start light. I opened and shut the door to make sure it clicked and pressed the start button again and nothing. I tapped around the panel with the side of my fist and pressed it again and it began working. Well today different story I went to start it and it did the same thing. I tapped all over front of the


The problem is more likely the door switch is failing or out of adjustment/loose. You will need to remove the door panel. This is easy to do. There is a video at ... Kenmore 24 in. 74382 / 74384 / 74389 Built-in Dishwasher

Dishwasher/diplomat-adp8342 not draining,left standing for a few months and now programe panel wan't work,if i turn it off then press the panel a few lights will go on but nothing semms to work,


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

My Kenmore 665.15962990 has quit working suddenly. The lights on the front control panel light up and will change if pressed, but when I turn the dial to on nothing happens. I have checked that the door is properly latched.


... Kenmore 17259 Free-standing Dishwasher

I have a Whirlpool dishwasher model #DU920PFGQ4. The controls locked light is flashing, and when I press the air dry key for 5 seconds it won't unlock, however the cancel/drain light starts flashing. When I press the cancel key the controls lock light will stop flashing, but will resume as soon as I release the cancel key. I have tried disconnecting power for 24 hours, but as soon as I plug it back up it does the same thing. Nothing else on the control panel will work.


... Whirlpool Dishwashers

My LG 24 in LDS 5811 ww quite working in the middle of a cycle. I have power to the machine, but no lights come on, nothing works. I turned off the power and removed the front pannel. The large brown wire and large orange wire that are plugged into the back of the control panel start to smoke. So does the large black wire and the large white wire. Any ideas, is this the heater or is the panel bad?


The unit will need a new Wire harness, Pump/motor assy, Main Pcb and inner door liner.\015\012Contact LG @ 1800 243-0000 they may help you out. ... LG 24 in. LDS 5811 Built-in Dishwasher

I have a KitchenAid KUD1021RWHO dishwasher that will not turn on when I hit the start button. The LED lights work when I press cycle selection ie. "normal" but when I press the start button nothing happens. I have waited for a couple of hours and then it will start. However during the last week it has happened more frequently and now it has not worked for the last (2) days. Any ideas as to what the problem may be? Thank you for your help!!!


Hello,\015\012\015\012This is a very common issue on these units. The touch pad has failed. You can try to flip the breaker off for several minutes and see if that clears the code. More than likely the touch pad will need to be replaced.\015\01 ... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

The control panel on my Electrolux/Icon dishwasher is not working. The only light showing is the red start/cancel light. When I press it to start, nothing happens and the light remains red. What could be wrong?


... Electrolux EDW5505ESS Built-in Dishwasher

I cant get my dishwasher to turn on, i press the normal cycle and the light flashes 4or5 times and nothing happens, i've unplugged it and tried all of the cycles nothing works


Count the exact number of flashes prior to the pause - this is the error code necessary to diagnose the problem. What is the model number also? ... KitchenAid 24 in. KUDI01TJ - Multiple Color Built-in Dishwasher

My smeg dwi 710 dishwasher keeps flashing on the diplay panel and won't change to another wash selection. it wont close and wont start. the light is stuck on the heaviest wash selection and just keeps flashing on and off and on and off. i have tried turning it off, keeping buttons held down and nothing seems to work. there is nothing in the manual that says what the flashing means so i dont know how to fix it.


... Smeg Dishwashers

Dishwasher won't start and it is plugged to working outlet. Control panel lights do light up. When I turn the setting dial to start, nothing happens. It looks like the last cycle never finished as there is water on the bottom. Any thoughts what might be wrong?


... Whirlpool DU912 Dishwasher

My Whirlpool Dishwasher ADP931 has stopped working. It stopped in the middle of the cycle with 2 to 3 inches of water on the floor of the compartment. I mopped out the water and tried to restart the dishwasher. The green "on" light now comes on when I press the start button. but nothing happens (no motor comes on,no water enters).Repeating the above action several times does not help the washer to restart even though the other function lights will come on when the knob is turned. saturn1914


Hi,Whenever you see such symptoms, Time for you to investigate it properly. Check the below guide :-\015\012\015\012\015\012\015\012\015\012Power from the house\015\012\015\012Is\015\012there power getting to the dishwa ... Dishwashers

Won't start. Seemed to be working fine a day ago. Then in mid cycle I opened the door because I was on the phone and it was too noisy (normal noise). Now , I shut the door and press start and nothing happens. No lights on the instrument panel. Nothing. Thanks.


You may have simply tripped a breaker, but if not it may be this.This may be a faulty door switch. If you look into the door locking mechanism carefully, you can see a small plastic bulb located either to the right or left of the locking Jaw. S ... KitchenAid 24 in. KUDU02FR Built-in Dishwasher

I own a Maytag MDB5100AWB three lights are flashing on the panel, the clean button, rinse only and heavy wash. I've tried turning off the breaker for 20 minutes, pushing the buttons in sequence, holding them down, nothing seems to work. It's done this before and a repairman pushed the buttons and it worked. Is there anything I can do to avoid another service call?


... Dishwashers

Our bosch dishwasher is not working, when we press the button to turn on nothing happens, no lights, nothing, we have checked the fuse and thats ok. many thanks gail


You may have to turn off power at main box, and check wires at bottom of machine and any other junction box , from dishwasher to main power box. pull on wires to see if they will come apart. ... Bosch Dishwashers

Whirlpool dishwasher model GU2-400-XTB7 Problem started with display cycling through delay times. (1 hr, 2hr, 3 hr and so on.) Was able to cancel that for short periods and then it would repeat the cycle. Was able to run dishwasher by pressing different buttons. Then it would start a cycle but did not run full cycle. Now control panel doesn't work at all. When buttons are pushed, lights do not light up and nothing happens. Is stuck in lock mode.


... Whirlpool GU2400XTP Built-in Dishwasher

I have a GE Quiet Power 3 that has completly died. I cannot get a light to come on or anything to beep when pressing buttons. I checked the circuit breaker and outlet and they are both working fine. I tried pressing and holding the reset button on the front control panel and nothing. It seems to have just died at 2 years old. Anyone have a solution? GE wants $80 just to look at it.


A dead set simply means a cut off of power supply. Open the back cover of your dishwasher . Locate the area where the AC cord is located and look for the plastic fuse holder which is usually installed in one of the AC cord line open it and replace t ... Dishwashers

I have a single dish drawer and it was working completely fine yesterday but today it wont turn on, there are no lights, nothing, no amount of button pressing is working please help


Assuming the circuit breaker at the mains is ok, you have a faulty power board or the thermal fuse in the heater assembly is blown.\015\012\015\012To replace you will have to take the drawer out of the housing making sure you don't pull t ... Fisher and Paykel 23 in. DD603H SS Free-standing Dishwasher

MDBS561AWW MODEL. Front panel lights work for "Cycle select", but when I press "Start/Cancel" nothing happens.


... Maytag 24 in. MDBS561A Built-in Dishwasher

Hi, I have an AEG oko favorit 64800 and when I turn it on and select a program it doesn't work. The power light comes on and the digital screen comes on but it looks like this -- --. I try to press the buttons to select the appropriate program but nothing happens. There is no alarm code displayed in the digital box. Thanks Louise


... AEG 18 in. Favorit 64800 Free-standing Dishwasher

KitchenAid 24 in. KUDI02CRBS stainless Steel Built-in Dishwasher: Just stopped working before Christmas. I had washed a load a day before, and the next day I couldn't use the Rinse Cycle. The lights turn on for Normal and Heavy, but nothing happens when I press Start. I played with the breakers a couple times, to try to "reset" the machine, but it didn't do any good. I really don't want to be spending a lot of money on that dishwasher, especially after reading all the horror stories abo


... KitchenAid 24 in. KUDI02CRBS stainless Steel Built-in Dishwasher

My dishwasher's buttons will not work at all. Nothing is lighting up. I have already checked the breaker (not tripped, but I turned it off and then on again just to rule that out)... I assume that it is some control panel (the manufacturer said that it is a covered part... but I will have to pay the tech to come and install). Just trying to determine if it would be something that I can do myself and save some $. the unit is only 3.5 years old...


... KitchenAid Architect? II U SERIES KUDS03ST Stainless Steel Built-in Dishwasher

I have a Miele Dishwasher G1023U , after pressing on/off button the control panel light comes on in the drying cycle not the Wash/Rinse . Water does not come into the machine , can not turn it off at stop/start button only at Main on/off power button. Only had Dishwasher 2 weeks, was working fine. The water tap is on, no kinks in hose.


... Dishwashers

Kenmore Dishwasher Model 15782: Problem: None of the front control panel buttons work...no lights when pressed, nothing. Breakers have been checked, door latch checked...help!


Worked great one day next day would not turn on at all ... Kenmore 24 in. 15782 / 15784 / 15789 Built-in Dishwasher

I have a GE monogram zbd5900 that continues to drain, won't shut off. The drain pump just runs. None of the lights on the control panel will come on, tried pressing and holding buttons to clear, nothing. Turned off and on circuit breaker (even left it off overnight) and did not change. Drain is not blocked, pulled the unit out and put water in the bottom and it pumped the water out just fine. any thoughts?


See if you can access the tech sheet, should be on the right side of the underside of the unit after you remove the toe panel, or perhaps in the console. Almost sounds like a stuck key pad but the tech sheet might shed more information on this malf ... Dishwashers

A few days ago the dish washer was running fine, maybe a single wash every day. Then, out of no were the logic seems to have left the machine. If you pressed the "normal cycle" button it would blink for about 30 to 45 seconds then the front panel would go blank. All LED lights would turn off, like it finished doing the diskes, never running a single cycle. I unplugged the machine to let all circuits reset, that worked for two days, two washes in that time. Today I'm back to a machine that will n


Your control panel is faulty and will have to be replaced. This is the main brain of the machine. Normally when a cycle doesn't start the timer is bad, but when your control panel doesn't do anything, then it is faulty. ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0965 seconds