Having problems with your Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher ?

I cannot be sure of the make/model - there is no power

\015 We have just moved into a house with an integral Bosch dishwasher. It has been a bit temperamental since moving in, the switches did not always work first time, then over Easter it completely stopped working, there is no power. We have checked the fuse in the plug.\015\012\015\012We shall be installing a new kitchen soon so we can manage without it until then, but I wondered if there is anything else we could look at in the meantime, or is it likely to be something that would need to be repaired by an engineer - it is not under warranty nor is there any repair contract.\015

Answers :

It sounds like you have a bad controller which is an expensive part if it is over five years old. However, there is a recall on some Bosch dishwashers which involves replacing the control. If you call Bosch at 1-800-944-2904 they can tell you if your model is involved in the recall.
Repair Help & Product Troubleshooting for Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Brand new haier hdc1804tw wont start. i press the power button unit beeps once and power light comes on but i cannot select cycles. unit will then beep every five minutes. i have made sure there's water and unit is level. i have left it unplugged for over five minutes with same resulting issue.


... Haier HDC1804TW Dishwasher

8575637 Brand new dishwasher installed about a month ago. Its been used about 10 times and in the middle of a wash cycle, completely stopped with no power. Have checked the plug, outlets, breakers. Cannot get any of the buttons to light up, have checked to make sure it wasn't locked out - no power at all. Manual is not helpful. Any ideas?


... Whirlpool GU2400XTP Built-in Dishwasher

I cannot be sure of the make/model - there is no power


It sounds like you have a bad controller which is an expensive part if it is over five years old. However, there is a recall on some Bosch dishwashers which involves replacing the control. If you call Bosch at 1-800-944-2904 they can tell you if you ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Starts cycle, drains ok, then "intake/drain" LED comes on solid for 4 seconds, flashes 4 times, solid 4 seconds, flashes, etc. no water coming into dishwasher. DOUBLE CHECKED the intake filter its all OK ! how do i 'reset' the machine? Im pretty sure the sensor is goofed up and needs to be reset but i have tried holding various buttons, start, power etc, cannot figure out how to do it


... Miele G2430SC Dishwasher

I have a Baumatic BDW 45.1 slimline dishwasher, the unit will power on but I cannot select a program. I was able to place the unit in to reset mode once by holding down 'P' and power cycling the unit. This then allowed me to choose a program and complete a full wash cycle. Now I cannot repeat this steps and the unit remains with just power light on. There are no Error codes displayed at all. Could this be a problem with the front panel?


... Baumatic 18 in. BDW45.1 Built-in Dishwasher

My Hotpoint diswasher suddenly stopped working last night. It seems like it has no power to it, as the motor or pump does not seem to come on at all. Obviously when I get home from work, I will check the obvious first - making sure it has power to it, connections are secure etc. (I had a wire break before) If it does have power, I would assume checking the door switch and timer is next. Any suggestions, and any suggestions for checking the door switch and timer??


Sounds like your on the right track. I would use an ohmeter to check the resistance of the door switch by placing the meter probes on each side of the switch. Test while opened and closed position. Same with timer ... Hotpoint Dishwashers

An electrical panel breaker switch was replaced after the microwave and dishwasher both lost power. The microwave works after replacing the main panel breaker. However the dishwasher will not show any power. Checked the internal circuit board, no burned areas, cannot find an internal GFI reset, what can I do to get power restored to the main control panel or even the unit itself? Rick C


1)check any fuse in the circut board.(blown off)\015\0122)check any loose connection of neutral (or)phase wire to the machine(or)in the switch. ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

My wife and I just moved into our house and cannot get anything on the dishwasher to activate. We have checked fuses, lightswitches that might be wired to DW power -- nothing has worked. Is there a universal power switch I am missing?


Sounds like a power supply issue. Take off the lower panels below the door and look to the right side of the opening, you will see a little square steel cover. This cover is where your power comes into the dishwasher. Follow the line coming into the ... Whirlpool DU930PWS Built-in Dishwasher

I have a Frigidaire FDB1100...I have no power to the dishwasher. I've checked the breakers and none of them have been tripped. Not sure where the plug actually goes to but I have checked the power cord and it's tight which means that it's still plugged in...of course Frigidaire has no customer service on the weekend.


Same problem . i will check for line voltage in box under unit and then continuity to panel. have no schematic for LV troubleshoot ... Frigidaire Dishwashers

Campbell Hausfield Pressure washer model 1549. After a few years of storage, I cannot prevent the powerful spray leaking from the connection between the Gun and the Lance. I replaced the O-Ring, and tried other means unsuccessfully. Spray from the joint is almost as powerful as spray from the lance nozzle. The Briggs and Stratton engine has been cleaned and operates well. The pump operates well. But the lance connection refuses to seal.


Hello,Most likely, the housing has split and seal is not being made. There is a chance that the hose is leaking where the fitting is crimped on (my experience, but different pressure washer). Are you able to see a leak when turned off b ... Campbell Hausfeld Pressure Washers

Bosch Dishwasher I have a Bosch Dishwasher that is a little over a year old. Loaded it up and ran it last night. Got up this morning to unload it, and load it again. Got it all set and went to start it but there is no power. The circut breaker looks fine. But no power to the machine. Not sure what is going on, or what needs to be done. Thanks....


... Bosch SHU3306UC Built-in Dishwasher

I have verified power to the Kenmore 15951 unit, but controls appear as if no power. I have tried hitting hi temp, heat dry, high temp, heat dry sequence like my reapir man suggested, to no avail. Not aware of any reset buttons. I have cleaned out the filter as well. Not sure where to go from here.....Rick


... Kenmore Dishwashers

Old dishwasher had power, I connected a new dishwasher and it doesn't work. I double checked and made sure I turned the power back on at the breaker box.


Hello, have you tried plugging something into the socket the dishwasher is plugged into.\015\012\015\012Hope this helps. ... Dishwashers

Dishwasher fault had leak,when opened bottom plate, could not see any obvious leak problem,hand dryed what componets i could. made sure no wires were loose then screwd back bottom plate,turn power back on but power button flashing continuously know,any advice plz


The flashing power button is a bad sign. You may have flooded the circuit board out or there may be a bad component as a result of the flood. Difficult to know from here.\015\012\015\012Most flooding on dish washers is caused by a faile ... Dishwashers

I have kenmore 665-16032401 clean light blinking and cannot reset cycle. Power was out for several hours, happened during wash cycle possibly, when came back on the light is blinking and cannot clear it or resume anything.


... Kenmore 24 in. 16032 Built-in Dishwasher

Have an electrical circuit that has stopped working. Romex circa 1930. The breaker is fine. There are 4 ceiling lights and 3 outlets on the circuit. There is power through the hot wire leaving the breaker. Tried wiring to a different breaker to be sure. Still no power


If there is power leaving the box, you have a broken/damaged wire somewhere.If all the lights and outlets do not work - the problem is with the common (return) (white) or a broken/damaged wire before the first item in the circuit.If the b ... Dishwashers

No Power Hi. My dishwasher wont start. I loaded it and cannot get any lights to light up on it. There is no power to it at all it seems. I tried flipping the breaker but there is still nothing. The door locks, so that shouldnt be the issue. Is there a way to reset the machine? What should I do?


I have the exact same problem with my Kenmore Type 575-0. It was working one daym it went into dry storage for a year and then when I took it out of storage it would not work. Ive already tested the thermal fuse and there is nothing wrong with that. ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

My dishwasher has no power . I had work done on the floor which caused vibrations. My water connection was leaking which I fixed but I found out that It has not power. Not sure if the vibration caused some wires to disconnect. What should I check before I pay $130 for a repair man to diagnose the problem.


Call the technician. Have him state on the bill that whoever did your floor caused the electrical malfunction ... KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher

Problem to turn on the KitchenAid dishwasher, model #: KUDP02FRSS1. I have this machine for over 2 years. After one year, sometimes, I cannot touch the touchpad to select some option of the cycles and options. Shutoff the power, and wait for few hours, it seems to work. Unfortunately, now the only cycles I can turn on is "Heavy Duty" and I can not hit Start to start the cycle. The other option on the touch pad I can select is the "Cancel". I turned off the power this time for 2 days and it seems


Your touchpad is likely faulty. Sometimes called a control panel. You can get parts, manual, pictures, part numbers, and more at partselect.com or repairclinic.com ... Dishwashers

Problem to turn on the KitchenAid dishwasher, model #: KUDP02FRSS1. I have this machine for over 2 years. After one year, sometimes, I cannot touch the touchpad to select some option of the cycles and options. Shutoff the power, and wait for few hours, it seems to work. Unfortunately, now the only cycles I can turn on is "Heavy Duty" and I can not hit Start to start the cycle. The other option on the touch pad I can select is the "Cancel". I turned off the power this time for 2 days and it seems


The electronic control board is most likely the issue. I would replace the pab that controls the dishwasher functions. The control board controls the cycles and the wash time selection as well as the on/off function of the dishwasher. ... Dishwashers

Fisher & Paykel 2 drawer dishwasher: I too cannot get power to top drawer. 4 days ago we had an F1 code. My husband pulled out drawer, wiped up water, and dried it out. Put it back in overnight, and both drawers worked fine. Now the bottom drawer is okay, but no power to top. Help!


He might have unplugged something in the proccess of drying the bottom ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Hotpoint HDA3400g dishwasher is not running. I have checked to make sure it has power. Took the washer apart, checked that it had power through the door switch to the timer control, all is well. Still not running or getting water into the dishwasher. Any ideas besides replacing the water inlet valve? Will this dishwasher cycle through if it does not have water?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. Please check for the following if your dishwasher\015\012is not working-- ... Hotpoint 24 in. HDA3400G Built-in Dishwasher

Child Lock light glows without pressing Energy Saver Dry button for four seconds. Cannot turn off by pressing Engery Saver Dry button for four seconds. Turning off main power and turning back on doesn't solve problem. But turning off main power for extented period, over night, and turning back on does fix proble for a very short period but Child Lock does come back on by itself. Is replacing the Console Assembly the only fix? Is there some button sequence to disable Child Lock altogher?


The mini manual for this dishwasher is located behind the kick plate. The mini-manual reveals that the child lock (called a control lock in the manual) can be disengaged by pressing and holding the air dry button for four seconds.or ene ... KitchenAid 24 in. KUDS25 Built-in Dishwasher

The normal cycle and cancel green light are flashing but dishwasher will not run. I cannot get any buttons to work, the resume does not do anything. I tried killing power from the circut breaker but same problem when power came back on. any ideas?


Best Answer - Chosen by Voters\015\012First, press and hold down Cancel and see what happens. That may reset the cycle.I did however find this online for the normal light flashing:The reset sequence used was ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

No power on the main switch inside the door, checked the fuse in the plug changed with new and no success, we had 2 poss 3 power cuts yesterday but the dishwasher was not working at the time? christmas time help. not sure on the actual type as it was in the integrated kitchen when we moved in 2 years ago an no manuals.


Make sure there is power coming from the house panel by checking the breaker for the dishwasher. ... AEG 23 in. Favorit 50750Vi Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0793 seconds