Having problems with your Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher ?

I have a Bosch SHU9915UC/U11 dishwasher, installed in 2002. Recently, our hot water heater had to be replaced, and we were without hot water for five days. Air got into the hot water pipes, and dried out all the debri in the lines. When we got the new hot water heater going, all of the sediment in the pipes ended up in the in-line screen filters in various appliances (clothes washer, etc.). I have cleaned these out, and these appliances are fine. Since then, the dishwasher has been shutting


Answers :

All inlet valves have a screen built into the valve itself,shut off the water remove the entire valve and you will be able to see built in screen,if you flush out the debris from it and re-install the valve it should work fine. 
Repair Help & Product Troubleshooting for Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Bosch SHU9915UC/U11 dishwasher, installed in 2002. Recently, our hot water heater had to be replaced, and we were without hot water for five days. Air got into the hot water pipes, and dried out all the debri in the lines. When we got the new hot water heater going, all of the sediment in the pipes ended up in the in-line screen filters in various appliances (clothes washer, etc.). I have cleaned these out, and these appliances are fine. Since then, the dishwasher has been shutting


All inlet valves have a screen built into the valve itself,shut off the water remove the entire valve and you will be able to see built in screen,if you flush out the debris from it and re-install the valve it should work fine.  ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Even though I turned up the thermostat on my hot water heater, the water in the dishwasher does not seem to be hot enough. Mold is growing in the food grinder and even though I choose the heat dry option, the dishes are never dry. Yet, when I touched the element, I got burned. The dishes are not getting clean because it doesn't seem to be hot enough to cut the grease.


Hi, \012I have an older dishwasher also and recently my wife alsocomplained about it not cleaning right... so me being the man I am tried invain to clean the things... Bought new spray arms online and installed them inminutes...now the thing works li ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Asko dishwasher D5122XXL I've got the F2 light flashing. How do I reset it? Or do I have to get service people to do it? I think there's nothing wrong with the pump or drain, since I actually poured a jug of hot water in to the dishwasher. ( it's hooked up to cold water pipe)


... Asko D5122XXLS 24 in Builtin Dishwasher

BF41 Dishwasher with a leak stuck in mid cycle Hi, I have a 'general domestic Appliance Ltd' BF41 (95+G709394) dishwasher which recently started leaking at the door. After replacing the seal the problem seemed to ease, then recently the problem started all over again and the leaking got worse. A couple of day ago I couldn't stop it leaking and now it's stuck in mid cycle and even though the water is washing inside the machine it never gets hot inside or finishes the cycle. Ive tried stopping and


... Dishwashers

Water usage for the Kenmore 2 Draw Dishwasher - 465.1332. I am considering an ''instant'' Hot Water heater, or a Point of use hot Water heater. I am unsure of the size to get since i do not know how much water is used per cycle.


... Kenmore Dishwashers

Dishwasher I have a whirlpool dishwasher that does not appear to be getting hot water. The washer water is cold initially and only seems to get warm once the heater in the base of the machine heats it. The hot water supply line does not get hot so I presume no water is being supplied. Is the water supposed to be hot at the start. If yes could this be caused be a faulty inlet valve and if so how can I check. The dishes are dirty especially on the top rack. Thanks for your help. David


Gendos is on track with his question. I have the same dishwasher and it doesn't get enough hot water to clean the dishes and runs for hours because the heating element wasn't designed to heat water, just maintain it. The only solution we have found ... Whirlpool GU2400XTP Built-in Dishwasher

Purchased in 2003. Dishes were exquisitly clean till 2008. Our water heater temp was set at 140 temp. This heater was replaced with a heater now set at 125 temp. In the past two years dishes are nowhere as clean on the the normal start setting. Should I go to the Pots and Pans start setting to get hotter water or should I turn up my water heater? All this is assuming that water is not hot enough. Does the washer heating element ever burn out?


Try turning on your water at the sink for a while on hot let it run then start the wash cycle that should help. what that will do is let the cold water run out of the pipes and therefore you will have a hot water start. ... Kenmore Dishwashers

We have a Hobart Dishwasher Model # WM5H. Our Booster heater will not heat the water hot enough. We have cleaned the lime out of the heater, and then it will work for a few weeks and then will not heat the water hot enough again. Any Suggestions.


... Dishwashers

My Bosch dishwasher is taking hours (at least 3 - maybe more) to complete a cycle. There is gummy, yucky stuff building up inside - sorta pinkish brownish. Could the water not be hot enough? A couple of months ago we installed an on-demand hot water heater and I wonder if that could have anythig to do with it. I've tried running the hot water in the sink first but that doesn't help. Any ideas


If your on demand heater is one of the small ones that mounts under the sink, it will not flow enough water to fill your dishwasher. the dishwasher is waiting for the water level to fill before it starts washing. your bosch will heat its own wat ... Bosch SHX46A07UC Built-in Dishwasher

My De Dietrich is not filling with water - pipe is on and water available. I've been away for a month - just got back and tried putting on the dish washer but it seems that the water isnt getting through to the machine even though the water pipe is on and waters available? any ideas - really grateful


Yes, lots of ideas. You need to disconnect the water line where it attaches to the dishwasher valve and see if water is flowing. If it flows, then you either have a clogged inlet valve (there is a screen inside the valve that catches debri from the w ... De Dietrich 18 in. VW7451 Built-in Dishwasher

No hot water from insta hot water heater


... GE GLDA690MWW / GLDA690MBB Built-in Dishwasher

My Bosch diswasher is hanging up in the cycle (at 102 mins. in normal cycle and 38 mins in quick cycle). I hear what sounds like a one second pumping of water into the sink area, a pause, and then another one second pumping of water, on and on, but there's no progression beyond this point. One possible cause: a few weeks ago someone turned off the hot water at the heater and another person tried to run the dishwasher. The dishwasher did not function because it could not get hot water. Perhaps


Hi\015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. To start with check the water inlet valve which is located\015\012behind the lower access panel on the left or right side of the Di ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

FDW60 Fault Hi, I have exactly the same problem. My dishwasher starts and washes ok but appears to get very hot during the drying phase and then the two lights fast and eco flash warning of a heater problem. I suspect either the heater, thermostat or control PCB. As the rest of the cycle seems of and the water gets hot then I'm assuming the heater and thermostat are OK. When the dishwasher attempts to dry is when the problem starts. Did anyone find out what there fault was? Thanks


Hold down the start key and you will re- set the D/W. Please Rate This !!! Thank YOU !!! ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

What could be causing white powdery residue on dishes, glasses & silverware? I have checked the heater element - seems to be hot, using Cascade powder as usual, we have and have had hard water, we do have a new water heater set on 'low' setting - temp of water measured at 113 deg at kit tap. This washer has worked well for 12 years, then white powdery residue. Thanks, Phil


I wont vista ultimate product key ... Kenmore 13869 / 13864 / 13862 Dishwasher

I've got a hotpoint bf168 dishwasher,been working fine until y'day when nothing washed, realised there was no water coming into it. Change water inlet pipe but still nothing, I can hear water going thru the pipe but then just seems to empty itself. Any ideas guys .


Hmmm.... could be the controler. or a stuck valve... have you tried to reset it? turn off power and turn it back on... ... Hotpoint 23 in. BFI68 Built-in Dishwasher

Kitchenaid dishwasher - small pieces of food are left on otherwise clean dishes. Water level comes to about 1 inch below heater coil. I ran it without dishes (or soap) and added about a quart of water so that level came to about 1/4 inch below heater and that's when I noticed food pieces on drain surfaces (nylon filter under bottom spray arm unit and circular plastic "trap" surrounding it). Spray arms holes are clear and water is hot.


It sounds as if you figured the solution out. The holes in the spray arm(s) get plugged by small debris, (tooth picks, seeds, bits of plastic like candy wrappers, etc) and the water does not reach the dishes to wash and rinse effective ... Dishwashers

White film, spots and dirty dishes, Water at first is not hot even after running the facucet, but I opened it later and it was hot. 140 degrees is what I have it set for on my hot water heater.


Problem is hard water. go to www.dishwasherfilter.com. problem solved ... Bosch Dishwashers

Loud humming when the water enters the dishwasher. The copper pipe vibrates. The dishwasher is approximately 11 years old. Problem slowly getting worse over time. I tried to tie down the copper pipe in the basement to no avail. When I closed the right angle stop valve and reopened, the problem got much worse and won't go away even if I grab the pipe. Only happens when water enters the dishwasher.


The fill valve solenoid has gone bad.u need to chg the fill valve assly.it is very easy to chge ad it is mounted on lhs bottom corner of the unit behind the toe panel. ... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

Whirlpool Quiet partner 1dishwasher (model DU1055XTSQ2) that is not filling all the way--water supply is working correctly. Also, the water is not getting hot, the heater coil looks very mottled.


... Whirlpool DU1055XTSQ Built-in Dishwasher

HDW101SS does not heat water. Heater element mearures 28 Ohms. Temp Limiter is N.C. Temp controllers TS50 & TS60 not found. On economy wash timer moves as normal then stops when red heater light should come on. If the timer is assisted one click it will progress as normal but no hot water.


Hi.If the temp limiter shows no continuity, there will be no voltage reaching the element contacts. The high limit is connected in series with the heating element. If the hi limit is open the element will not get power. Any technician wil ... Haier HDP18PA Stainless Steel Free-Standing Dishwasher

I have recently changed my dishwasher over from a direct hot water pipe into the dish washer, to a cold water pipe but the temperature lights keep flashing and then the cycle, which has barely begun, stops. wat to do?


A dishwasher requires a hot water line to operate properly. The dishwasher is indicating the water is too cold to even begin a cycle.\015\012\015\012Charlie ... Dishwashers

Got a Indesit Di620 Dishwasher that trips RCD after power up & immediateley as you shut door.Fault is definately related to pressure switch, disconnected pipe to switch and then able to start cycle, without tripping, small amount of water out of pipe,but cycle only lasts for a few minutes, then stops. ( blowing into pressure switch trips rcd )How can i test switch, or is it a water level problem ??Any help would be good, thanks S.C


... Dishwashers

I have a CDF8 348 dishwasher. We went away on holiday and it accidentally got switched off mid cycle. When we got back and turned it back on there is a continuous beeping noise and the water doesn't seem to be getting through. The water pipes are working.


You need to unplug unit wait 12 hrs for ICs to Drop overload then Plug Back in. ... Candy Dishwashers

The dishes come out with white film on them. During the washing cycle water is not hot, it's only luke warm. I thought it was the heater but the drying cycle works well. Is it all connected to one heater? It is not because of hard water. It worked fine just last motnh. Please help! Thank you!!!


Are you having any issues with your water heater at all. Make sure to run the water at the kitchen sink on the hot side first ti ensure hot water is getting to your dishwasher. Also make sure that the jet dry dispenser has jet dry in it. Hope this h ... LG LDF8812 Stainless Steel Built-in Dishwasher

Bosch SGS5312GB/12 Dishwasher I had a control board. Worked fine except didn't heat the water. Got it repaired (new PCB). Now the only thing it does is drain. Clicks every 20 secs and carries on draining. Got a new board. Does everything (including heat the water) except it does not drain before, between, or at the end of cycles. It does drain when while filling, and if the flood detection rod is raised manually (also drains if the inlet pipe beyond the pressure sensor is blocked - found


... Bosch Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1449 seconds