Having problems with your Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher ?

When i turn on the dishwasher it starts at the drain part of the cycle then dries then ends


Answers :

Looks like micro controller problem. Take BOSCH service center help
Repair Help & Product Troubleshooting for Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

When i turn on the dishwasher it starts at the drain part of the cycle then dries then ends


Looks like micro controller problem. Take BOSCH service center help ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

KUDU03STSS2 The dishwasher won't start and you cannot select a cycle. Hiting cancel twice will turn a small steady light on in the time window were the spining light normally is before a cycle starts, at which time closing the door will drain the dishwasher. Tried using the reset combos: hot wash, heat dry, hot wash, heat dry - all lights came on but nothing reset. Also tried same sequence doubling the heat dry. Unpluged for ten minutes, still nothing. Can select rinse, but unit does not start,


... KitchenAid Dishwashers

GU1500XTLS3 Periodically won't start. Dishwasher has power because pressing cancel causes dishwasher to start draining (even though there is no water). Door switch works because opening door prevents starting drain cycle. No other button on control panel will work except for the 'air dry' / 'lockout' button. Turning off circuit breaker for 15-30 minutes and then turning circuit breaker back on seems to fix the problems but only for a couple uses and then it stops working again. Need ad


This could be the 'fill switch', which is the level sensor. Could be a plastic tube that exerts air pressure into the tube as it fills, make sure it's clear and open. The dishwasher has a sensor that monitors the door being closed too. Some use a hig ... Dishwashers

The GE Profile Dishwasher will not allow me to start without the heated drying light coming on. I want to wash without this headed drying at the end of the wash. When I try to turn it off it turns the start cycle off. This happend over and over again when I want to turn on the machine, It finally lets me get an unheated dry wash started to complete. A problem every night. PDW7800N15CC. Serial MM8243388


... GE 24 in. Profile PDW9800J Built-in Dishwasher

Hotpoint dishwasher machine go's through wash cycle, through to the end, after dry cycle ends there is always 2 inch's of water left in it that doesn't drain out' but some water is added when new cycle is started, then throughout wash cycle whenever water drains it never drains completely, always leaves 2 inches of water before adding more water to begin rinse cycle. what do I need to do?


... Dishwashers

Dishwasher works fine except that after the drying cycle, water slowly builds up in the bottom of the dishwasher. It did this a few years ago for several months, but then it stopped doing it altogether. I did nothing to fix it. Now it's started doing it again. I run the dial around to a point where it drains, let the water drain and then turn it back to off before the drying cycle begins.


Hello,\015\012\015\012This would mean that the dishwashers water valve has failed. This is a simple repair to make yourself. The lower access panel would need to be removed, four screws. You can purchase the part from the link below.\015\012 ... GE Dishwashers

I have a Kenmore Elite Dishwasher Model 665.172824000. We think it stopped part way throught the dry cycle. The green "Clean" light has been flashing since in 7 flash cycles non stop. I tried pushing the Cancel button, it starts the drain pump then stops and we are back to where we started. I tried to start a new wash cycle but when I close the door and push the start button it just give 3 quick red flashes and then nothing but the green clean light flashing again. I shut the breaker off fo


So sorry but the partsdirect site for sears locked down my computer. Check where the drain hose connects to your pump and see if there is a small device the hose connects to that has 2 wires going to it. If it does unplug the wires, turn power off, w ... Dishwashers

Miele Diamante G 2150 SCU Dishwasher problem ----The program cycle indicators "Rinse", "Drying" and "End" flash at the same time. The drain pump is running when the door is open. I have reset the power and cleaned the drain pump and non return valve and Spun the propeller several times in both directions to check for obstructions. Still has the same problem. Water is being drained continuously even with power switch on dishwasher turned off.. Had to shut the breaker off to get it to stop. A


Hi\015\012\015\012Plugged system or a jammed drain pump can cause these issues, also make sure the drain hose is not blocked. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remo ... Dishwashers

Whirlpool dishwasher part #3385181. Machine had gone thru wash cycle and was starting to dry. Smelled electrical burning smell, opened washer door and washer was filled with smoke. Turned everything off, cleared smoke, and the washer water dispenser is very hard to turn. Washer has symptoms of burnt up motor that turns water dispenser. Machine is 12 years old. With cost of replacement motor and possible part (pump?) that might have clogged and caused motor freeze up, is it worth fixing or junk


... Dishwashers

I have a Whirlpool Dishwasher, I had a problem with the garbage disposal, so it was replaced, I hurt myself at the time and my wife had someone install the Garbage Disposal and now you run the dishwasher and no water is brought in to the dishwasher. It does drain, because I put water in and ran that part of the cycle and drained, it does turn on, it does dry but not bring in water is there something basic the guy forgot to do? Any suggestions, thank you.


He turned the hot water faucet under the sink for the dishwasher ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Our ge profile dishwasher 6 years old does not shut off at the end of the cycle, even after 3 to 4 hours, you put your hand on the door and you can feel slight vibration if you open the door and close it , it will start what ever cycle you had it set on all over again. It cleans and dries the dishes, but I have to turn the breaker off. at the end . Paul


... GE 24 in. Profile PDW9700JII Built-In Dishwasher

Hi: I have reviewed the forums and tried to fix this issue. Have a Miele G2120 dishwasher that at the end of the cycle - the three (rinsing, drying and end) orange lights begin blinking in harmony. I have removed the triple filter, and two plastic parts to the impeller and made sure all was free of obstruction. I then pulled it out removed the drain hose from in-sinkerator; removed the water line and checked for obstruction. When it gets into this condition - the majority of water drain


Hi The issue seems to be with the float switch assembly that is bad and should be replaced. Float assembly is found inside the dishwasher's tub, on the bottom. The water that ... Miele Inspira Series Dishwasher w/ 6 Programs and 5 Temperatures - G2120 / G2120BL - Blac 24 in. Built-in Dishwasher

Dishwasher: Kenmore ultra wash sensor quiet guard plus. I'm in a rental so I don't have the manual or model number. A few days ago it just wouldn't start the wash cycle. When you press normal wash then start the no heat dry and lock lights flash every other second or so but nothing happens. I can hit the cancel button and it will make sounds like its trying to drain, and after about 5 minutes stops. I've done the heated wash/ no heat dry sequence to try to reset but no luck. Also tried turn


... Kenmore Dishwashers

I have a zanussi ZSF2440 dishwasher, when it turned on by the power button on the front you can choose a cycle and start it, Once the cycle is started it fills up with water but doesn't stop until it over flows setting off the flood protection, which cuts the power, so all the lights on the display go off and stops the water flow and drains the dishwasher and keeps draining the dish washer while the flood protection is on. It seems as if the dishwasher doesn't know when its reached its correct


... Zanussi Dishwashers

Whirlpool Dishwasher ADG 450. Start as normal and it keeps intermittentlly stopping and starting. Washs / drains fine, but sometimes cycle seams to last for a couple of hours. I think it is four beeps when it is stopping and then immediately starts again. We had a problem months ago where as the sink was draining into the dishwasher out pipe, so dishwasher wasn't draining / filling up. Fixed the problem by turning the pipe the other way so water couldn't flow that way - but I don't know if that


... Dishwashers

Edgestar DWP60ES prematurely ending wash cycle, will not drain properly, beeps alot


Most likely the dishwasher has a minor leak in the base under the wash sump. this could be tripping the flood switch which causes the pump to run continuously. when the leak dries up you are able to start normally until the leak trips the flood switc ... Dishwashers

My G832SC is not draining at the end of the cycle. It runs the entire cycle, and the dishes appear to be clean. The soap dispenser has opened and the dishes are rinsed. However, the dry cycle doesn't run because the machine doesn't drain at the end. The intake/drain light is flashing. If I reset the machine and start a new cycle, it will perform an initial drain and the water level does go down. We checked the tri-filter and the valve pump thing, rinsed both. Checked the hose under the sink. We


... Miele Slimline G832SCi Built-in Dishwasher

Hi, The machine will not complete a cycle. I think it may have started when the power was turned off at the mains during a cycle. Symptoms are : - You can turn machine on, select a program, press start button, close door, machine appears to begin cycle as normal, water seems to load, then 2 minutes later drains, and 1 minute or so after that the machine beeps 3 times to indicate cycle is finished. Dishwasher tablet door never opens, dishes not cleaned. Have tried : - cleaning filters; - turn


It is likely the dishwasher is locked in some diagnostic program.\015\012If you provide the dishwasher model no. then I can try to find out the keys you need to press to get it out from it. ... Whirlpool Dishwashers

Candy CDI1012 Integrated dishwasher. When I turn on the dishwasher and start it - for some reason it can not go the whole way through the cycle. When I open the door the - programme light is flashing and water is still in the bottom of the dishwasher - ie mid cycle. The water will only drain if I put it into another program to drain away - but as the dishwasher was mid cycle - the dishes are not clean


Hello mm1973,It could be because of bad door latch switches / blown thermal fuse / blown or oversensitive control board. In all these scenarios, a dismantling of the machine is required. If you have no prior experience, I'd recommend get ... Dishwashers

I accidentally opened dishwasher towards end of cycle..and it appeared to stick. I managed to get it to drain but now I cant start it as no water comes on when I turn it on. I have only just pais £99.oo from Bosch mechanic to have same fault fixed please can u help.


Try reseting the unit by doing the following.\015\012It depends on what model you have on how to reset it. See if the following two models is one that fits your model. \015\012\015\012Open the dishwasher door far enough to expose ... Bosch Dishwashers

My Dishwasher starts, then stops after 30secs and won't continue draining. Everytime I turn it back on it comes up on the steam cycle and won't go to any other cycle, drains for 30secs and stops again. Power light is flashing. Have tried holding power button down for 10secs with no effect. Filter is clean, pipes are straight-no kinks. How do I get it to start working again? It is a whirlpool dishwasher, ADP5550.


... Dishwashers

I have a Triton dishwasher. Last cycle, it completed washing then started drying and started beeping and the drying light is flashing. When I finally opened the latch, the beeping stopped, but the drying light is still flashing. The dishes were clean and warm - they air dried the rest of the way. I have not been able to get the drying light to go off. I have turned the breaker off over night, and flipped back on. The dishwasher goes back to flashing washing, and then clicks to drying and th


Hi,\015\012Make sure the salt level is ok - add 1Kg of salt if you have not done it in a while, and check rinse-aid level if apliccable.\015\012\015\012If this does nothing, then remove the lower kick panel for access to a data shee ... GE Dishwashers

Our GE Triton Dishwasher, mod# GSD5620D01BB is 10 years old. A problem started two days ago where; when it runs through a normal washing cycle; it contuously beeps about every 1 second when it reaches the Drying Cycle and the LED Green light flashes next to the Drying . I reset the breaker and tried again; same thing happened as it went through the normal cycle and when it reached the Drying part; same thing happened. The dishwasher is cleaning and everything else seems to be working fine.


The drying fan and vent system seems faulty.\015\012\015\012Refer this diagram. Item 918. ... Dishwashers

Bosch dishwasher My Bosch dishwasher finished a wash cycle and was showing the "END" light on, however, the motor was still running as though it was stuck on the drain cycle (there is a gurgling sound from where the eater drains off beneath the filter. Subsequently turning the washer on just repeats the apparent drain cycle with a constant gurgling sound (it does not kick into wash mode). The number on the manual is & 258 (7705).


Is all the water draining from the tub? if not the pressure switch will not reset and it will continue to try and clear it self...check drainage system.\015\0122. pressure switch is jammed on..build up in the sensing chamber..commo ... Bosch 24 in. SHU43 Built-in Dishwasher

Hello, I have a Neff Dishwasher S5453X1GB/74 and it's not draining the water out at the end of the cycle. I have unscrewed the filter and released the impeller. I have also cleared the waste pipe that runs to the sink waste and put loads of cleaner in the dishwasher. The pipes seem to be clear as water goes somewhere during the cycle but backs up at the end. A few times when I started a cycle the water did not spray out but I could here the drainer or motor? running. I jetted water through th


... Neff 24 in. S5453X1 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2625 seconds