Having problems with your Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher ?

My Bosch diswasher is hanging up in the cycle (at 102 mins. in normal cycle and 38 mins in quick cycle). I hear what sounds like a one second pumping of water into the sink area, a pause, and then another one second pumping of water, on and on, but there's no progression beyond this point. One possible cause: a few weeks ago someone turned off the hot water at the heater and another person tried to run the dishwasher. The dishwasher did not function because it could not get hot water. Perhaps


Answers :

Hi
\015\012\015\012


\015\012\015\012

Thanks\015\012for using FixYa. To start with check the water inlet valve which is located\015\012behind the lower access panel on the left or right side of the Dishwasher. If\015\012the water inlet valve is bad you have to replace it, also check the main water\015\012line for clogs/obstructions. If still the issue is not resolved then it's a bad\015\012float switch and needs to be replaced. Please accept the solution if the issue\015\012is resolved or post a comment for further assistance.
\015\012\015\012

Thanks
\015\012\015\012

Rylee

Repair Help & Product Troubleshooting for Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Bosch diswasher is hanging up in the cycle (at 102 mins. in normal cycle and 38 mins in quick cycle). I hear what sounds like a one second pumping of water into the sink area, a pause, and then another one second pumping of water, on and on, but there's no progression beyond this point. One possible cause: a few weeks ago someone turned off the hot water at the heater and another person tried to run the dishwasher. The dishwasher did not function because it could not get hot water. Perhaps


Hi\015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. To start with check the water inlet valve which is located\015\012behind the lower access panel on the left or right side of the Di ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Subject is Bosch dishwasher SHU6800. There is a soap residue left on dishes. Residue is not visible. Using two glasses taken from a recently completed wash cycle I rinsed one under tap water and then filled glass with tap water. The second was just filled with tap water. There is noticeable soap bubbling and foam in the second glass. Starting the 10 min rinse/hold cycle following completion of a full 60 min wash cycle results in considerble soap foam in the bottom of the tub. Have tried thr


WHAT IS WRONG WITH YOUR DISHWASHER? \015\012\015\012\015\012\015\012 \015\012For a detailed Dishwasher ill ... Dishwashers

I HAVE A 2 YEAR OLD BOSCH DISHWASHER. WATER WILL NOT PUMP INTO THE MACHINE. IF I POUR WATER IN IT PUMPS RIGHT OUT. THE DOOR WILL NOT LATCH AND CAN PUSH RED DIFFERENT CYCLE BUTTONS ONE AFTER ANOTHER. YOU USE TO HAVE TO SHUT THE MACHINE OFF TO GO TO A DIFFERENT WASHING CYCLE LEE


Hello thereThere are a couple of reasons why a dishwasher will not pump water into the machine or even work once the water is in the machine i will post the possiable reasons and some troubleshooting tips for this in 2 different post's ... Dishwashers

Kenmore Elite dishwasher not cleaning well and leaving dark stains on the dishwasher walls. water pumps in to correct level and pumps out. First cup of soap the water is just warm. Second up its hot and also the rinse cycle. Bottom filters are clear.


Check the following to address this issue1. No water\015\012\011\011\011Make sure you get water to the dishwasher. Check to see if the water \015\012\011\011\011shut-off valve (located under the sink) is open. If you ge ... Kenmore 24 in. 16049 Built-in Dishwasher

Hello, my Bosch Classixx dishwasher SGS43E42EU/21 has me stumped. It starts by taking in water but when "filled" pumps out for a couple of seconds then refills for say 10 seconds more before another 2 or 3 seconds of pumping out. This cycle continues for ages without starting to wash. I've tried various things: - checked the Auto Stop valve isn't being activated by leakage (removing the polystyrene float and bottom tray makes no difference - there's no leak) - the valve seems to operate it


Hello Dave,\015\012\015\012Sounds like an overfill problem - the symptoms are consistent with a failed pressure switch. Water enters the dishwasher through a chamber which has a float arm connected to a small microswitch -this is the pres ... Bosch Dishwashers

Hygena Dishwasher My dishwasher does not drain the water away properly. About an inch of water lies in the bottom after a cycle. Incidentally, when I put it on a "cold rinse" (which is the only other setting to "wash 60c") it rinses with hot water. Is my switch and my pump broken or is there another possibility?


I would check for blockage, can you hear the pump trying to drain.\015\012pull all the metal pieces ouy and have a look. ... Neff 18 in. S5943 Slim-Line Built-in Dishwasher

My Bosch Dishwasher does not drain all the water out of the dish washer after the finishing cycle...I usually start the washer and then push the drain cycle and it starts to pump for about 10 seconds and stops and starts and pumps again for 10 seconds and stops and then pumps for about 25 seconds and stops....doing this manual drain twice empties the dishwasher of the excess water....what may the problem be?


... Bosch 24 in. SHE43C05UC Stainless Steel Free-Standing Dishwasher

Our Hotpoint Dishwasher Model HDA200X-73BA has two little white plastic pipe stubs poking out of the bottom of the dishwasher. During one of the cycles--(I don't think it is the drain cycle)-- some water is being released from one of these pipe stubs and then it stops and the other one runs some water. They each only run for a few seconds, but the water is just running on the floor. These little pipe stubs are about one half inch in diameter and project out of the bottom of the dishwasher about


Hello. go to the sears direct website, click on the blue link below, and enter your model number. ou can then access an excellent parts diagram which will show these stubs and what may be missing from them. Joe\015\012\015\012 ... Hotpoint Dishwashers

Whirlpool dishwasher doesn't seem to fill with enough water despite good water pressure. Therefore, pump sounds like it is cycling from pumping water for about 2 seconds to going dry for 2 seconds to pumping water for 2 seconds to going dry for 2 seconds, etc. Spray arms rotate only for the 2 seconds when pump is actually pumping water. Dishes do not get clean.


... Whirlpool 24 in. GU2548XTPS Built-in Dishwasher

I have a Sears Kenmore Elite dishwasher Mod. # 665 - Ser.# FJ4805735 that intermittantly skips the wash cycle and pumps the hot water out just after filling. This unit was built in 2000 but the entire drive unit was replaced about 6 yrs. ago. If the problem lies in the electronics is it worth a do it yourself repair. I have an antique (1970'S) appliance repair background and electronics is not my forte. Money is tight and I would like to squeeeeeeeze another couple of years out of this appli


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012Would you be able to supply the complete model number. The Kenmore elite dishwashers where made by many different manufacturer's over the years, even within t ... Dishwashers

I have a Kenmore Ultra Wash Dishwasher (Model Number 665.15634) that will not fill up properly. When I try to run a cycle (any cycle), the first thing the dishwasher should do is fill up with hot water. But in my case, my dishwasher fills for about 10 seconds, then stops. Then tries to fill again for about 7 seconds, then abruptly stops again. And this process goes on and on and on. The dishwasher never fully fills up nor starts the wash sequence properly. Once the dishwasher fills up, it


... Dishwashers

My trusty Bosch s510 Dishwasher which has been going strong for about 17 years (at least) has just decided not to empty itself. I noticed the bottom was full of water after a wash. I emptied all the water out by hand and presuming there is a blockage in the drain tried using a plunger to unblock it. I have since put it through another cycle and half way through water started leaking out of the front. At the end of the cycle the bottom of the dishwasher was again full of hot 'soapy' water. If th


Same problem, so went out and bought a new bosch. Problem with the S510 was cured by lubricating the pump out motor bearings with a squirt of WD 40. If you don't know which pump, follow outlet hose to pump outlet.Les ... Bosch Dishwashers

Hello, I have a CONSTRUCTA S9W1C dishwasher with aquastop. Unfortunately, I tried once to start it with the house water supply closed. Of course it stopped after a few seconds. After that time, when I start it, the water pumps works and after some seconds the cycle stops. It gets no water. I've checked and noticed that no water passes through the aquastop valve. The aqua stop has two wires that get into the dishwasher. Do you have any suggestions? Thank you for your time Alex


... Dishwashers

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of water is let in when the pump turns on and the washing cycle begins. Opening the door shows that the water level does not reach the bottom of the float. When I close the door, the wash cycle begins again but stops after a few seconds. This is when the water begins to fill again. This time, the wat


Larry,The float is generally for overflow conditions and will interrupt power to the fill valve solenoid. If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water ... Whirlpool GU2400XTP Built-in Dishwasher

ZANUSSI Da 6341 dishwasher, Flooding in middle of cycle. Sometimes at start of cycle (5-10 mins) washers floods and water comes out of front. If i move timer to end of cycle pump works and water is pumped to sewer. This doesn't happen every time. Sometimes cycle works perfect and after that doesn't


... Zanussi 24 in. DA6141 Built-in Dishwasher

I have an Ariston LS245 dishwasher, have just had the pump replaced, as it had shorted out, due to water in the bottom tray where the water detection float is, also a new drain hose fitted. Have just run a wash and after running a while, presumably to the end of the rinse, wash and dry cycle, then one of the cycle phase lights, the one for 'soak' blinks constantly. I switched the machine off and had a look to see if a wash had been done, the dishes look clean. In the book it says that if one


... Ariston Technologies Dishwashers

Our GE dishwasher (5 yrs old, Model GLD4250L00CS) only fills with water half way when the unit is started. The inlet valve was replaced with a new one, but that did not solve the problem. When started, the dishwasher fill cycle runs for 41 seconds before the wash cycle begins. Repair workers told us we probably need a new ECU (Electronic Computer Unit). My questions are: Is 41 seconds the correct time for the fill cycle for our model? What else could be the reason for the unit not filling pr


Hello &\015\012Welcome to FixYa\015\012\015\012Check this\015\012 ... Dishwashers

My Bosh Model# SHE4AM02UC/01 Is not cycling. Started with the soap dispenser not opening, progressed to the drain pump not staying on. When you turn it on, the pump runs for 2 seconds. water solenoid opens for another two seconds, and then the "clean" light comes on. If I go to quick wash, or to pot scrubber it might do a regular cycle. I did pull the pump to remove a piece of glass before this all started, but can't imagine that would be the cause.


... Bosch SHE4AM02UC 24 in. Built-in Dishwasher

I have an Asko w66 front load washing machine that will only wash one way with a 60 second time delay and washes the same way again instead of reversing. At no time will it wash the other way. At the first spin cycle the water is pumped out but the wash drum will not spin. The pump continues to pump and will not stop while the one way wash continues. The timer stops at this point with the one way wash and pump still pumping continuously.


... Asko Dishwashers

My Thermador dishwasher DWHD64EP/54 does not get the dishes clean. We checked all the usual things--water to the dishwasher is hot, filters clean, spray arms working and not clogged, detergent cups working, proper amts of detergent etc. We find that no steam is produced during the cycles, we find that the when choosing a cycle and power boost incorrect cycle times are now displayed compared to previous usage when the dishwasher ran normal. Some of the longer cycles now show only 24 min


... Thermador DWHD64EP Built-in Dishwasher

Frigidaire Dishwasher This is my second dishwasher in 18 months. Water leaks out the bottom of the dishwasher. It did it on my first one now it''s doing the same thing.Could it be the water pressure from the city water line? How could this happen to two dishwashers in a row? The leak starts immediately when the wash cycle starts.


This is a simple solution, the brass nut that connects the heating element to the base of the dishwasher is cracked and needs replaced. It takes just a few minutes to replace, just remove the nut after TURNING OFF THE POWER and take to your local par ... Dishwashers

My kenmore 665 dishwasher will not pump water to the lower and upper spinner arms. The pump entry screen assy seems to have one tear in it and is dirty. However water does come out if I take off the lower arm assy. Is this a sign that the pump is bad and is not pumping enough water to move the arms or is there another problem?


The pump is probably defective (low pressure). Enough to spin the bottom but not the top. ... Kenmore Dishwashers

Water will not drain out of bottom of dishwasher.It will go through the whole cycle but will not drain. This is a Frigidaire model no.FDB510LCS3 Serial no.is:noth70219331.Pump hose was disconnected and drained completely,dishwasher was put through another cycle and still ended up with water puddled in the bottom!! Could this dishwasher be called a lemon??? Does the pump need replacing?? I have noticed on your website that many others are having the same problem.To me it appears that it may be sh


Check the input to the drain hose to make sure it is not blocked by something like a cherry pit.  That could cause the water to not drain fully. ... Frigidaire 24 in. FDB510LC Free-standing Dishwasher

DWF 415 Ikea Whirlpool Dishwasher has constant green blinking light. Drain pump works ok (as it will pump out a jug of water if I tip it into it!) but no water comes in. Cycle stops about 30 seconds after thre is no more water to pump. Any ideas on how to fix?


Anyone got an answer to this, as I have exactly the same fault. \012\012\012Dishwasher appears to switch on OK, then after a short time (20 secs?) the pump noise stops and the green light flashes - it seems to e a sequence of 7 flashes, t ... Whirlpool GU2400XTP Built-in Dishwasher

KitchenAid KUDP01DLBS2 dishwasher. Runs for a very long time on any cycle; time does not seem to advance. (takes 2.5 hours or more for normal cycle. "sensing soak", "water heating" lights on for a long time, even though it appears that water is not being heated. Checked incoming water temp, is hot. Did not do this when new, something has changed. Typical cycle was 1 hr 10 min. before.


Sounds like the heater inside the dishwasher is not working. The machine is trying to get the water up to a preset temperature, probably in the neighborhood of 140 degrees. That is one of the things that it is sensing.After the machine fi ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2493 seconds