Having problems with your Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher ?

Water is clogged in the bottm of the unit. how do I clear the drain?


Answers :

Hi,
\015\012
\015\012The drain filter is clearly visible at the bottom of the wash compartment but there are several possibilities as to why there is still water in the bottom of your washer:
\015\012
\015\0121. Blocked drain filter
\015\012At the bottom of the wash compartment, there is a fine mesh grille and a plastic cylinder which protrudes from it. Grip the plastic cylinder, twist anti-clockwise and pull it upwards. To clean it, remove any debris from the cylinder, rinse then replace in reverse order of the above.
\015\012
\015\0122. Blocked/kinked waste hose
\015\012Check the waste outflow hose at the back of the washer for any kinks or other damage. Also remove the hose where it attaches to your sink (or waste outlet) and check for any blockages.
\015\012
\015\0123. Blocked waste disposal / sink trap / waste outflow
\015\012Make sure your sink is draining efficiently. Clean as necessary
\015\012
\015\0124. Faulty waste pump
\015\012If all of the above check out, you may have a faulty pump. Please post back for further advice regarding this after completing the above checks.
\015\012
\015\012Regards,
\015\012BElectric
Repair Help & Product Troubleshooting for Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Water is clogged in the bottm of the unit. how do I clear the drain?


Hi,\015\012\015\012The drain filter is clearly visible at the bottom of the wash compartment but there are several possibilities as to why there is still water in the bottom of your washer:\015\012\015\0121. Blocked drain f ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Bosch dishwasher model shx36l fails to stop pumping. The drain was clogged. I cleared the drain. Dishasher backed up, water overflowed. Clog has been fixed. Dishwasher will not stop trying to pump water out. There is NO water inside dishwasher. I wish to run another load however unit fails to respond. Pump is operating even when front door to doshwasher is open. Turning the power button to OFF is the only remedy to stop drain pump from operating. How to fix?


... Bosch Integra® 500 SHX46A0 Dishwasher

I have a Frigidaire dishwasher. Model FDB520RHS0, Serial TH92539147. The drum fills with water but will not drain. I purchased the unit about 2 years ago. It has been used sparingly and mostly on light wash. I removed the basket and could find nothing blocking the drain. Is there a fix? Can I replace the drain pump? The unit is making a noise as if it is trying to drain but nothing is happening. I have checked the drain line for clogs and it is clear and the terminal end is conn


... Frigidaire 24 in. PLD2560LCC Energy Star® Built-in Dishwasher

Our kitchen drain clogged recently and water drained back into our VUD141 dishwasher. A plumber cleared the drain, and turned on the DW - which pumped out the standing water. But now, we have no water flowing into the dishwasher. The drain pumps, the heater works, but there's no water supply. The plumber who cleared the drain said he didn't DO dishwashers, and I cannot locate the owner's manual since we prepared for a move.


Hi\015\012\015\012 \015\012\015\012When the dishwasher won't fill and the water supply is on,\015\012then the issue is with the water inlet valve which is either clogged or\015\012blocked, you can try to clean it. If this wont so ... Viking 24 in. Professional Series VUD141 (Ultra-Premium) Built-in Dishwasher

Dishwasher drain is hooked to a food disposer and until recently the unit worked fine. Last week following a cycle a couple of inches of water did not drain out. All food is removed from dishes, silverware, etc. prior to loading and the food trap in the bottom is completely clear. I ran the unit empty through a Lightwash cycle and afterwards the water level (that which didn't drain out) looked to be the same as before. The dishwasher is run 2-3 times weekly whereas the food disposal is


Hi, The I don't think the problem is with the loop and the 32" above the floor.If the dish washer was removed from one house to another, did *********** ever have a dish washer in the house before that he replaced this one with? The reason I am aski ... Dishwashers

Drain Clogged I have a Kenmore Quiet Guard Plus dish washer. The water will not drain from the unti. I believe the drian in the dish washer is pluged. I removed the 8 screws from the pump/strainer unit at the bottom of the unit I removed the top that the screws were holding donw, but can't figre out how to get to the drain to unplug it. The center metal unit is exposed and nut head is exposed. What do I do next to get to the drain hose to unplug it?


You might try pouring liquid plummer in the drain part and jet it set it shouold eat through whatever is in there ... Dishwashers

Subj: ge dishwasher mod/gsd3960looss - 1yr 4 mos old. problem: will not drain only used 6 times. last use after cycle done, water remained. had to hand drain. removed cover and checked drain area, no debris found. drain tube is connected to disposal by clear plastic tube; no clog in tube. the sink drains are clear and the disposal works normal. dishwasher drain seems to be stuck in closed position. this model has the touch pad controls. any solution????


... GE Dishwashers

Kenmore (Whirlpool) 655 1589910 Dishwasher. Fills with water, motor makes horrible noise (buzzing / loud hum). Dishes do not wash and there is no evidence that any water pumped up to the spray arms. Spray arms are not clogged. We have a fully functioning water softener so it is not a hard water issue. Unit does drain normally. Either filter is badly clogged or pump is bad. How do I get to these parts to check them out?


You need to clean/ check the chopper. sounds like you have a bad motor. about 2-300 dollars for the part ... Kenmore 15899 Built-in Dishwasher

I have a GE monogram zbd5900 that continues to drain, won't shut off. The drain pump just runs. None of the lights on the control panel will come on, tried pressing and holding buttons to clear, nothing. Turned off and on circuit breaker (even left it off overnight) and did not change. Drain is not blocked, pulled the unit out and put water in the bottom and it pumped the water out just fine. any thoughts?


See if you can access the tech sheet, should be on the right side of the underside of the unit after you remove the toe panel, or perhaps in the console. Almost sounds like a stuck key pad but the tech sheet might shed more information on this malf ... Dishwashers

My SGS55M72AU/65 does not get rid of its drain water, although that wee pump in the bottom is clearly working (which I could see after removing filters and pump cover). There is no blockage near the drain pipe connection, so I infer there is a blockage somewhere inside the dishwasher, in a place I can't get to without further instruction. I've removed most of the drain water and pulled the unit out, so I could lay it on its side and start taking screws out. But I much prefer to have some guidanc


Ok i am attempting to help you although i dont see your make of dishwasher but im using what i know without manual. to ensure there is a blockage in the dishwasher remove that hose you checked at garbage disposal or vent and leave it disconnected an ... Dishwashers

Water drainage I have followed the manual instructions for clearing all appropriate filters on the intake and outflow side but the cycle does not complete and leaves a pool of water in the base. What next? I have the G568/858 Plus Incognito unit (thisis the closest part # to my actual unit--can't even find teh right # listed...), and aI m dealing with the sme issue. I have followed all of the recommended steps in cleaning the filters, traps, etc. There are no kinked hoses. The water drains to b


YOU NEED TO REMOVE THE LOWER SPRAY ARM AND REMOVE THE SHELL THAT IS COVERING THE PUMP AND FOOD SHREDDER ,HERE IS WHERE YOU LOOK FOR A CLOG. ... Miele 24 in. G892SCU Plus Built-in Dishwasher

Ran the dishwasher and the water didn't drain completely. Checked the drain line for clog - it was clear. Scooped out the remaining water (barely covered the flat wire mesh filter in bottonm of the machine) and cleaned off the canister mesh filter and carefully relocked the filtyer in place. Tried to run the machine last night. Soap tray opened but apparently no water cycled through the machine as all the soap was in the bottom of the machine. The heat never turned on to dry the dishes and


Hello Ramona Doug,\015\012 Try disconnecting power from your dishwasher for a few minutes to clear the memory and then reapply power again. Start a wash cycle without dishes on the hottest water setting and after a few minutes.. pause the wash ... Bosch Dishwashers

There was a puddle infront (not under) my dishwasher last night. I think my drain is clogged. It is a base model Admiral Ultima. There are no screws holding the basket. Does it just pry out? I tried a baking soda/vinegar solution to try to clear the clog. A pot of boiling water afterwards does not drain at all. Should it be draining when the dishwasher is off? Any other ideas on what my problem/solution is?


... Admiral 24 in. DDB1501AWW Free-Standing Dishwasher

SHX46B I have a 4 year old Dishwasher that filled up with clean water on it's own and leaked on the floor. There appears to ba a float switch switch on the very bottom of the unit that runs the pump if this happens. It won't stop until I remove the water caught in the plastic base on the very bottom of the unit. Drain is clear and this machine has worked fine until now. I'm thinking it may be a bad or leaky fill valve but how can I check?


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Have GE Dishwasher model GLD6700N20WW,unit has stopped draining! Took apart and pump was running when check, but no water coming out. Checked drain line and pulled apart pump housing, all clear. Thought maybe pump has a silinoid built inside of it and was stuck shut, so bought new pump and same thing, no water will go thru! Please help me? Is it control module, or turbitity sensor possibly?


... GE Profile PDW8600J Built-in Dishwasher

Kenmoore Quiet quard 3 Model #665.74363K1 Serial #FS3502091 The unit will not drain properly. When in drain mode, it will drain slowly when diconnected from the disposal and lowerd to floor, and drains even slower at disposal level, or hooked to disposal. Disposal nipple is clear. I removed the hose and flushed it out with high pressure, found no blockages, hose flows freely and did not fix the problem. The motor is turning and seems to pump water fine, all wands are truning with powerfull spray


... Kenmore Dishwashers

Kitchenaid dishwasher - small pieces of food are left on otherwise clean dishes. Water level comes to about 1 inch below heater coil. I ran it without dishes (or soap) and added about a quart of water so that level came to about 1/4 inch below heater and that's when I noticed food pieces on drain surfaces (nylon filter under bottom spray arm unit and circular plastic "trap" surrounding it). Spray arms holes are clear and water is hot.


It sounds as if you figured the solution out. The holes in the spray arm(s) get plugged by small debris, (tooth picks, seeds, bits of plastic like candy wrappers, etc) and the water does not reach the dishes to wash and rinse effective ... Dishwashers

I have a General Electric Potscrubber dishwasher. When the cycle is finished, the water does not drain into the sink.I turned the unit upside down to look into the bottom. The motor turns freely. The instruction sheet I found in the bottom of the unit said to remove the filter screen and check the piston valve. I looked at what I thought was the piston valve, but I'm not sure how to check it. The line to the sink seems to be clear. The model of my unit is GSC3230Z03WW. The serial number is AZ627


... GE Dishwashers

We have a Kenmore Elite 665.13862 dishwasher that does not drain. It appears to go through all the intermediat cycles and washes the dishes fine, but the water doesn't drain. We've tried to clear out the drain as best we can. It doesn't appear to be clogged.


It appears your pump has failed in this instance.For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.I recommend both sites because ... ... Kenmore 13869 / 13864 / 13862 Dishwasher

I've had my Nautilus for 6 years and it cleans very well - but now, it won't drain fully and pools at the bottom of the unit. I have made sure that my garbage disposal was cleared first, too. and that water was draining properly in the sinks. I will need special tools to unscrew the drain filter in the dishwasher, right, or can I just use a pair of pliers to turn the little knobs? I am always careful to rinse all food off the dishes before putting them in the washer, but I guess I wasn't careful


If your model has the screen across the back with the filter, then yes use your fingers or a plier to unscrew the pop up valve assembly at the very back center of the dishwasher. Most likely, the cone shapped part has deteriorated and is not sealing ... GE Nautilus 24" Built-in Dishwasher

80% of the time the unit finishes with an inch of water still in the bottom. We always prewash dishes , so shouldn't be clogged drains and have only used the unit a dozen times because of the drying problem.


Hi Please note that dishwashers don't drain out the complete water such that heating element doesn't overheat. However, if it seems to be a lot more water then it is due to clogged drain filter or drain pump. Turn off the dishwas ... Frigidaire Dishwashers

The water is not draining and I may have a clogged drin. Where is the drains location in the actual machine and how hard is it to clear?


Your model number is 3 numbers a period and 8 numbers.We must have all those numbers to help.Example: 123.45678910 ... Kenmore 24 in. 16032 Built-in Dishwasher

I have dishwasher (Electrolux) model ewdw6505gs. How do i clear a code of 01? I fixed the disposal clog and the dishwasher automatically drained the water in the bottom. I just can figure out how to clear the error code.


I should inform you that that is a "leak detection error".\015\012You should check some of those hose clamps, they may not be tightened properly.\015\012\015\012Regards ... Electrolux Dishwashers

The cleaning liquid has never mixed with the water to pressure water. Do you think the line is clogged and if so, how do I take the unit a part to clear the line?


... Karcher PSI Electric Pressure Washer

Kenmore Ultrawash Dishwasher #665 - The drain is clogged and water leaks out when the dishwasher runs. How do you lift up the spinner so you can clear the drain?


... Kenmore Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1449 seconds