Having problems with your Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher ?

Will defective on/off switch prevent all power from initiating any activity within the dw unit


Answers :

Repair Help & Product Troubleshooting for Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Will defective on/off switch prevent all power from initiating any activity within the dw unit


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

WP DW Mod # GU1200XTLS0: this unit filled with water and just stopped running. I have power to the unit. The control panel does not light up at all. Its wierd that I have power to the board and all the wires seem to have power! No burnt spots and no burnt smell on the board.Hmmm! Door latch and switches all check ok. Oddly it seems like the line power to DW goes all the way thru the unit and back through the nutural wire. Could the motor windings be burnt out?


Hello , there should be a fuse located by or on the side of the board with 2 wires going to it , one from the latch and one from the board ,it does come off , use an ohm meter to check it , it should ohm out or have low resistance make sure to take t ... Whirlpool GU1200XTLS Stainless Steel Dishwasher

My 3-yr old GE Profile dishwasher lost power soon after initiating wash cycle. Checked braker switch...fine. Checked outlet power...fine. Dishwasher power mysteriously came back on approximately 12 hours later. Initiated another wash cycle and lost power again after a few minutes. Water remains in bottom of tub. What's wrong????


First thing i would check is the actual wiring behind the toes kick\015\012you will seea wire box, shut the breaker off, open up the box and double check all your connections there,\015\012 the next step would be to check the voltage ac ... GE 24 in. Profile PDW8280JSS Built-in Dishwasher

Unit does not power up. checked power to unit ok checked power to latch switch - ok appears circuit board is bad. Traced 120v to board. Any other checks before getting new dishwasher?


Hi mgray770,\015\012It sound like you have done a good job already, but just a couple thoughts before you go buy a new one. If the board does nothing then it could be locked, check your owners manual or whirlpool.com for the exact unlock inst ... Whirlpool Dishwashers

Dear Sir/Madam,I have owned a Beko DW450 slimline dishwasher for 13 months and used it only twice, i wanted to use it last night but when i switched it on the drain pump activated and would not switch off. I powered down the dishwasher to see if that would reset it but unfortunately when i started it again it did the same thing - drain pump activated but would not stop running, it is impossible at the moment to carry out a wash programme. Does anyone have any idea on this problem. Thanks, Patric


... Bosch SHU5315UC Dishwasher

My Asko D3232 will not turn on. No power light will work and I've checked breaker and outlet for power (which are okay). Any ideas. Unit is 3 years and 2 months old. Is there any reset switch on the unit?


... Asko 24 in. D3250 Built-in Dishwasher

I have power to the unit but there are no lights on door when closed. Unit will not respond to any buttons and lock not on.I have opened up the door panel and have power to the door switch and then to the board.What is my next thing to check?


Ok so you have power going to the unit at the bottom if the unit is not under warranty? first are any LEDs operating at all when door is opened? if not you most likely have a control issue to test this you would remove the screws along both sides of ... KitchenAid 24 in. KUDI02IR Built-in Dishwasher

Removed rear toe-plate to detect leak. Leak caused by broken drain hose. Hose replaced. To do this the unit was tipped forward onto its front door to allow access to the base area. Water allowed to drain out the front base area. Unit re-assembled but now does not switch on. Water connected. Base-plate dry. No water was detected at upper-front control panel. Power is connected and reaching unit ( multi-meter test ). Tipping the unit forward seems to be the cause. Is there any fuse,


The micro switches are frequently replaced on the door handle and they don't need to ever get wet. A lot of amp draw burns those switches up while they are dry. If they were wet and power was applied then they got fried my friend. The good news is th ... Dishwashers

I have a AEG OKO_ FAVORIT 4040 dishwasher which has had very little use despite its age. The problem is that the switch that detects an over-fill is activated all the time and the pump continues to try and empty an already empty dishwasher even when the main switch is turned off, the only way to stop this is to turn it off at the power point I have had some sucess deactivating this switch by tilting the dishwasher forwards however because of the angle it sometimes overflows when filling. The ma


Hi there,This could be a problem on the control board of the unit. It could be faulty and need replacement or you may try to access the board and try to clean it.Make sure upon doing this all electrical connection to the unit ... Dishwashers

An electrical panel breaker switch was replaced after the microwave and dishwasher both lost power. The microwave works after replacing the main panel breaker. However the dishwasher will not show any power. Checked the internal circuit board, no burned areas, cannot find an internal GFI reset, what can I do to get power restored to the main control panel or even the unit itself? Rick C


1)check any fuse in the circut board.(blown off)\015\0122)check any loose connection of neutral (or)phase wire to the machine(or)in the switch. ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

No Power I have a bosch shx33 dishwasher. I just replaced the water valve because of a leak and now I can't start the dishwasher. It's like there is no power to the unit. I know there is power because I get a shock if I touch the two wires that are connected to the water valve. Is there another trip switch or something somewhere?


First let me say that using parts of your body to test for mains electriciy is a VERY VERY bad idea. You are lucky you are not dead. Please do not touch live parts again, get a multimeter or a mains tester.\015\012\015\012If there is mains across the ... Bosch 24 in. SHX33A02 / SHX33A06 Free-standing Dishwasher

Dear sir In an attempt to dislodge a blockage of my sewer line using Draino and a plunger some of the Drano ended up in the dishwasher and now the dishwasher will not run. My dishwasher is a SHU3036UC/U12. When starting the unit up it empties the unit but the cycle newer ends, in other words the timer does not advance to the next cycle, I have determined that the timer motor works by removing it from the unit and supplying it with power. One thought is, can the water level switch be stuck in


HiCheck this video and clean the drain pump assembly: ... Bosch SHU3036UC Dishwasher

AFTER A BRIEF POWER OUTAGE DUE TO ELECTRICAL STORM THE F1 CODE FLASHES AND PUMP RUNS CONTINUOUSLY. TURNING POWER OFF ONLY STOPS IT FOR SEVERAL SECONDS. TURNING OFF POWER TO DW AND BACK ON DOES NOT RESET. I HAVE REMOVED THE BOTTOM DRAWER AND CHECKED FOR WATER, BUT UNIT IS DRY. IS THERE ANOTHER WAY TO RESET THE SWITCH?


Hi there,The f1 fault is cased by a leak on the dishwasher.It is activated when water gets to a dangerous level in the base of the appliance near to the PCB.The main reason this happens is putting cups on the drop down s ... Dishwashers

Kitchenaid model KUDIO1ILBL6 The lights for Heavy Cycle ,Normal Cycle and Cancel blinking at the sametime constantly. The tech sheet is missing and the unit is appox. 5years old.have shut power down for 5 minutes .When power turn back on only the Heavy Cycle light blinks costantly. Have Ohmed out the door switches and check adjustment OK. Checked board strips and plugs for good clean and tight connections OK. Thanks


Hi, You need to reset the unit by pushing the buttons. Push the heated wash/heated dry a few times. All the lights will light up and the dishwasher will continue its . Let ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Is there an internal breaker switch that would cause the unit to loose power? I have checked the switch box to make sure the circuit breaked hasn't tripped.


Check where the pigtail ( the wiring harness that goes from the outlet to the actual dishwasher itself. This connection will more than likely be at the very bottom of the dishwasher and is in a metal box. Disconnect the power before opening the bo ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

House circuits OK, power to unit. No power within dishwasher as if it was not pluged in. Is there a circuit breaker or fuse inside? the modle number is WP920?WDB4. (The Question mark is unlegible)


Did you check the door switch for continuity? That will kill all control power. Just a thought.\012 GOOD LUCK ! ... Whirlpool DP920PF Dishwasher

I have a Kitchenaid model KUDL02IRBS1 dishwasher. It died with no lights to the front panel at all. I have power at the main wire connection to the unit. I checked the door switch and it works. I checked power at what looks like a solinoid on the circut board and it has 115V.


... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

Draper Power Wash 2121. Worked ok yesterday. Today just seems to be power to the unit when switched on with a bit of a hum -but with little pressure nor the normal loud working noise. Suggestions welcome. Many thanks.


... Pressure Washers

Bosch shu8806 Hello, I aquired a shu8806 recently and it doesn't work. It has power and water. I push wash cycle, indicator light comes on, shut door and nothing happens.  So the door switch seemed like a good place to start. Since I am an electrician I thought I would give it a shot. When plugged in, the wire from the motor is 120V but when jumpered to the neutral(common on the door switch), motor doesn't operate. Although, I have heard the motor turn over momentarialy when trying to run unit e


The pump may be clogged, or the motor start capacitor may be bad or some units have a fill switch wired inline with the motor so it won't start unless the unit is full ... Bosch 23 in. SHU 8805 Built-in Dishwasher

My wife and I just moved into our house and cannot get anything on the dishwasher to activate. We have checked fuses, lightswitches that might be wired to DW power -- nothing has worked. Is there a universal power switch I am missing?


Sounds like a power supply issue. Take off the lower panels below the door and look to the right side of the opening, you will see a little square steel cover. This cover is where your power comes into the dishwasher. Follow the line coming into the ... Whirlpool DU930PWS Built-in Dishwasher

Belling IDW604 dishwasher. Accidentally openned mid cycle, could not reset or switch off. Then had power cut. Dish washer now off and cannot be switched on or activaled at all. Have changed the plug fuse but still will not work.


The one link for all the solutions just click the link and solve any type of problem in kitchen ranges.\015\012www.applianceaid.com\015\012\015\012 the link ... Belling Dishwashers

Bosch dishwaher Model # SHX46A does not display indicator lights and does not function in any mode. There is power to the on/off switch that works and power to the control panel. Other wise the unit is dead. The problem occurs consistantly. I have not tried to fix this problem. Please advise. Thanks, Al


Having same problem, power to outlet, but unit is "dead", no lights, won't turn on. Unit is 6 yrs old and don't want to spend $100 for a repair man to tell me there is no hope....anyone else experience this? ... Bosch Dishwashers

Kenmore Ultra Wash dishwasher model number 665.1374 or 665.1384 I am a technician. This unit does nothing. It has power and ground. I have tested the door switches. They test good. If I unplug the unit and plug it back in then it will run a drain cycle, at least that is what I think it is doing. The motor runs for about 4 minutes. Once it shuts off, there is no further response. No control indicators illuminate. No response from pushing any of the touch buttons.


... Dishwashers

Powder solenoid I hav e an AEG Favorit 50700 sensorlogic dishwasher. As soon as I switch on, before even selecting a programme, the solenoid to operate the powder dispenser door operates, then stays activated until I remove power. I've taken the door liner off and the PCB looks OK - but I guess whatever powers up this solenoid has gone short circuit. Any idea what it might be or might look like?


Probably the main module ie the pcb you were looking at ... AEG 24 in. Favorit 50730W Free-standing Dishwasher

Kemore dishwasher 665.17029403 is hooked up, breaker not tripped but no power at all - lights will not come on. Power initially would be intermitent - lights on, then off, but now there is none. Is the unit worth repairing or a new machine a better option cost wise?


I would check the power conction under the dishwasher. Make sure the power cord is disconected or the breaker that supplys power to the unit is off. remove the kick plate at the bottom of the machine and locate the power concetion box and inspect th ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0668 seconds