Having problems with your Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher ?

SHX46B I have a 4 year old Dishwasher that filled up with clean water on it's own and leaked on the floor. There appears to ba a float switch switch on the very bottom of the unit that runs the pump if this happens. It won't stop until I remove the water caught in the plastic base on the very bottom of the unit. Drain is clear and this machine has worked fine until now. I'm thinking it may be a bad or leaky fill valve but how can I check?


Answers :

Repair Help & Product Troubleshooting for Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

SHX46B I have a 4 year old Dishwasher that filled up with clean water on it's own and leaked on the floor. There appears to ba a float switch switch on the very bottom of the unit that runs the pump if this happens. It won't stop until I remove the water caught in the plastic base on the very bottom of the unit. Drain is clear and this machine has worked fine until now. I'm thinking it may be a bad or leaky fill valve but how can I check?


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Miele Dishwasher Model G1040, Type HG03, NR: 32/65143704 The machine is three years old. The cycle reaches almost to the end, then all three LEDs merge together, and the pump runs continuously, even with the master switch off. I have taken the machine out and removed the base plate. When I first took the machine out of its position, I tipped it backwards and water came out of the bottom. All hoses and parts in the bottom section seem perfect in every way but the inside of the bottom plate indica


... Dishwashers

Bosch SMS4012GB dishwasher. Refused to fill. Found tray full of water in base of unit. Mopped up water about 2 litres. Machine works but lower reservoir on the side of the machine with float switch overfills and overflow leaks about an eggcup full each cycle. What is causing the overflow please?


An electric switch activated by air pressure. This device detects air pressure exerted on it through a flexible tube connecting it to part of a water tub. \015\012When activated, this switch then opens an e ... Dishwashers

I have an ADP6000IX Whirlpool dishwasher which is comming up with a Fault code Err4. The manual indicates overfilled and possible cause "too much inlet water", however there is no water sitting in base of machine, and have unloaded all dishes and Err4 still comes up. I have switched unit on and off at wall but has not re-set. I have disconnected water pipe from tap and reconnected.Is there anything further I can do?


Hi, \015\012\015\012You can solve this by cleaning and de-greasing the filter frame, basket and sensor Also there might be a low threshold for oils/greases/debris of any kind, so you have to rinse and load. By removing outflow tube ... Whirlpool Dishwashers

I have an Ariston LI45. The stupid thin one. It's not seen much work & is just out of Guarantee. It's stopped working & is showing 2 flashing lights. Stops partway in to a cycle with water in the base, but not enough to cover the element. Tried re-setting, no difference. I have also noticed that it's melted a plastic wheel off the bottom tray at the back. After reading problems with other washers, i'm guessing the water level switch & maybe element too. If this is the case, i'm ok finding the


... Dishwashers

Removed rear toe-plate to detect leak. Leak caused by broken drain hose. Hose replaced. To do this the unit was tipped forward onto its front door to allow access to the base area. Water allowed to drain out the front base area. Unit re-assembled but now does not switch on. Water connected. Base-plate dry. No water was detected at upper-front control panel. Power is connected and reaching unit ( multi-meter test ). Tipping the unit forward seems to be the cause. Is there any fuse,


The micro switches are frequently replaced on the door handle and they don't need to ever get wet. A lot of amp draw burns those switches up while they are dry. If they were wet and power was applied then they got fried my friend. The good news is th ... Dishwashers

I have a model MDB7100AWQ, it fills with water but the motot won't start. Is there a reset code for this model? I did find a melted off plastic spoon handle in the bottom, could this cause it to trip something in the unit? The lights on the door switches come on but it only clicks, and won't start.


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. To start with check the\015\012door switch if that\342\200\231s fine then you\342\200\231ll have to replace the ... Dishwashers

I have a kenmore 665.13719k601, i used the delay switch and now i found water in the bottom of the machine. the cycle most have stopped while i was away. when i returned there was water sitting in the bottom of the machine. The water is clean... I can not drain due to no access to power on the machine. I checked the breaker but it was on, so i reset it anyway... nothing.. any idea's


... Kenmore 13719 / 13712 Built-in Dishwasher

I am not getting any water out of the bottom spray arm in my bosch SGS47E02GB35 dishwasher. I have cleaned out the plastic pipe assembly on the left hand side of the machine and the plastic tubes that sit to the right of the pipes. I have blown through many of the other pipes to and dislodged quite a lot of debris which has now been cleared out of the machine. The machine completes its cycle and water comes out of the upper spray arm (there may not be as much water coming out as there should be)


1. Check that water can flow from main pump,though hose to propellor,that there is no blockage. ... Bosch Dishwashers

Good mroning after starting any program first the pump will run followed by water intake. After a while the machine stops and the light intake/drain starts blinking. Most of the time water will stay in the machine. After pressing the on/off bottom first switching the machine on again and starting a new program the machine pump start running emptying the water but than stops after a short water intake again. I opened the water stop but it seems to be ok. The filter inside the machine is cle


Good morning don't get shocked because ullu ki to abhi subah hi hui he ... Miele 24 in. G892SCU Plus Built-in Dishwasher

Zanussi dw927 not filling inlet valve changed,supply to machine ok, calls for water solinoid activates for about 30secs shuts off and machine does no more. cleaned out two blue plastic pipes situated under a plastic cover which were both blocked, and put a hose jet wash thru where they were situated to clean housing out, put blue channels back still not filling up and now the inlet solinoid wont switch off when when it should and programme advances heater now comes on with no water in.manually


... Dishwashers

E1 fault code Dishwasher runs for about 5 minutes. Water fills up at bottom of unit and then machine seems to pause then fault code E1 appears then water is pumped out from bottom of machine. There are no leaking pipes and drain is installed correctly. I installed a new wash pump and fault still appears.


Hi,\015\012I think both the heater and thermostat / trip switches need to be checked.\015\012If water is going in and out ok, then it seems to be waiting to heat the water. It sees a fault - so just clears out.\015\012Heating elemen ... Dishwashers

Hi, we have a Bosch Exxcel dishwasher which mid way through a cycle a button saying Check Water came on. we turned the machine off and opened the door and found loads of water in the bottom. my husband then scooped all the water out and cleaned filter in the bottom, where we did find some bits of plastic from the kids yoghurt pots, and took the water hose off the back and checked for blockages, which there was none. the water is certainly coming from the water pipe through the hose as we tested


Check your water level sensor. And also check to make sure that your pump is working correctly. It sounds like a couple of different things that need to be addressed. First check the water level sensor. It is a tube that is located from the back of t ... Bosch 24 in. SHU43 Built-in Dishwasher

Bosch dishwasher = machine on but no water, so the lower basin has water in it and because of it the FLOOD CONTROL SWITCH IS ON, so how do I drain the rest of the water so the FLOOD CONTROL SWITCH goes off? A plastic cover with a seal is stopping me from drain the water below?


If you can see the water use a shop vac if not you will have to pull the unit out and remove the left side panel after removeing the water you will need to find the leak that caused the bottom to fill with water ... Bosch 24 in. SHU66C05 Stainless Steel Built-in Dishwasher

I have a Kenmore Model 665.15955792 dishwasher. Water is leaking out the bottom of the door. I changed the door seal and the defusers but it continued. I took off the front of the door and I see the water filling into the base of the machine. When the dishwasher starts the cleam cycle, water is pushed up into the small square holes in the bottom of the door and then splashes up over the lip of the door and out onto the floor. It has never done this before, just started recently. I have had the d


... Kenmore Dishwashers

Last couple of days bottom rack of dishwasher not been clean on 65o wash, having emptied and run the machine empty etc it seems that whilst there is water being pumped through the roof mounted vents and to the "spinner" attached to the upper tray, the spinner attached to the base of the machine is not getting a) any / b) sufficent water pressure to make it spin...im guessing the feed is blocked?


... Bosch 24 in. SGS43C02 Classixx Built-in Dishwasher

Whirlpool DWF417W, Type 12155 A couple of weeks ago the machine failed to empty, leaving dirty water in the machine at the end of the cycle. Start a new program it emptied & all was then well. A couple of days ago we started a wash cycle as normal, shut the door, the pump normally runs for about 10 seconds then the cycle starts. However the pump just runs continuously?? After looking here there seemed to be a few links to the subject of water being in the base & the anti flood switch being ac


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Dishwasher not draining properly or not draining at all issues\015\012can arise due to different reasons ... Dishwashers

Dishwasher LFK-011S: First it occasionally gave four beeps (overflow) but no water in bottom or under. I then noticed that with lower water pressure machine worked ok few months. Now last week in the middle of program, drain pump started to run, machine gave four beeps and pump kept running even main switch off. Now when I plug in power cord, the pump starts to run immediatelly


... Fagor LFA013 SS 23 in Builtin Dishwasher

We have a Diplomat dishwasher ADP 8242 and its intergrated but have no manual, the machine switches on fine and starts its cycle, i switched it on before going to bed and in the morning it was still running so obviously knew something was wrong, when i opened it the dishes were not clean and there was water in the bottom which took a while to drain away, also the salt inlet is full of water, should it be like that? Any advice would be great thank you.


... Dishwashers

I have a Karcher K3.48M electric pressure washer which used to shut off when you weren't using the cleaning wand. This no longer happens and there is alot of water running out of the bottom of the unit. (This didn't used ot be the case) I expect a leak somewhere inside the unit, but I'm wondering even more if there is a pressure switch which has failed that cased the leak. In other words, if I find and repair the leak and there is a failed pressure switch, it will likely only break again. I can'


Hi you will have a 8 digit number on a silver plate on the machine with a number like 1.141-470.0\015\012Then go to www.karcher.com then on the left click on Europe, then you ... Karcher PSI Electric Pressure Washer

Our Fisher & Paykel single dish drawer unit (6 months old) is leaking limited water from its base down the front of bottom drawer below the unit's base onto the kitchen floor. One inspection by a technician failed to find any rectifiable problem. Unhappy, Wicks Road North Ryde


One drawer leaks can cause this problem. If you don't fix it. One day it will turn on the pumps from both units without any one touching them since the floor sensor at the bottom housing detects water and it will run for ever until you unplug the pow ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

Got standing water in bottom of dishwasher model #GSD5500GWW/CC/BB. We found some plastic cake decorating tips in the standing water, and hear crunching like more tips when we turn the machine on. How do we take remove the spinning thing in the middle, or anything else, that would allow us to clean out all th plastic tips?


... GE Dishwashers

Top arm does not turn in most of gibson amana an frigidaire this is done by ball in bottom of pump .it is clean.spray arm are clean .bottom arm move all the time.timer works it hesitates every so often and so ball will move an water should go up to upper arm but doesnt.common problem on these units but dont know how to cure?change ball.didnt work..on one unit changed pump cure problem for 4 months then returned....also does anyone know were u can buy the plastic they used to sell for dishwashers


Can yo give me the make and model number sol I can look at the service manual for you? ... Dishwashers

Model No: SE6 TIE 1 GB/17 Tecnik integrated dishwasher The dishwasher started to make a strange noise. I scooped the excess water out of the bottom and reset the machine but when switched on again it just pumps water into the bottom of the macine. I have removed and cleaned filters as per the manual troubleshooting section! Thanks for any assistance


... Tecnik Dishwashers

Just installed bosch SHE68E15UC dishwasher today and during first cycle E15 error came up and unit will not go into another cycle or allow me to program anything else - sanitize and rinse aid lights are blinking - water went into the machine and it started filling the bottom and wasnt draining - i then adjusted the filter and the water drained - but e15 error persists - what should i do - is it install issue or machine issue - please help- thank you so much


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1221 seconds