Having problems with your Bosch 24 in. SHU6802UC / SHU6806UC Built-in Dishwasher ?

Cycle time Just moved in, started the Bosch dishwashe that appears to be less than two years old, left for one-hour and came back to find the wash cycle still going; hasn't cycled in thirty minutes since I've returned. Is this normal? What is the standard cycle time?


Answers :

Yes its normal.bosch dishwashers use very little water and energy but,the cycles need to be longer to get the dishes clean. its perfectly OK.(ps use cascade powder if you can)
Repair Help & Product Troubleshooting for Bosch 24 in. SHU6802UC / SHU6806UC Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Cycle time Just moved in, started the Bosch dishwashe that appears to be less than two years old, left for one-hour and came back to find the wash cycle still going; hasn't cycled in thirty minutes since I've returned. Is this normal? What is the standard cycle time?


Yes its normal.bosch dishwashers use very little water and energy but,the cycles need to be longer to get the dishes clean. its perfectly OK.(ps use cascade powder if you can) ... Bosch 24 in. SHU6802UC / SHU6806UC Built-in Dishwasher

I have a new Frigidaire FDB1050RE diswasher. I ran it for the first time set on normal wash and pressing both the Hi-temp wash and heat dry button. This cycle is supposed to take a total of 89 minutes to complete including the drying cycle. After 89 minutes it was still in the wash cycle so I cancelled it to preserve sanity. In the instruction manual it states that the water temperature must be above 120°F. Our building's water heating unit is set at 110°F. Why there is a lower temperature


It should still work pretty well but you probably can't use the high temp wash because it will take too long for the dishwasher to heat up the water enough to satisfy the high temp washer thermostat. If the thermostat's calibrated closing temperature ... Frigidaire Dishwashers

KUDU03STSS2 The dishwasher won't start and you cannot select a cycle. Hiting cancel twice will turn a small steady light on in the time window were the spining light normally is before a cycle starts, at which time closing the door will drain the dishwasher. Tried using the reset combos: hot wash, heat dry, hot wash, heat dry - all lights came on but nothing reset. Also tried same sequence doubling the heat dry. Unpluged for ten minutes, still nothing. Can select rinse, but unit does not start,


... KitchenAid Dishwashers

My dishwasher is 6 years old it started making clicking and knocking sounds about a week ago. The display is blinking crazy at about 37 minutes left in washing cylce it blinks 37, HO, and CL. It blinks other numbers also. The water still seems to be flowing in and out fine. It's heating up and draining when canceled. I'm running it on normal wash and high temp. cycle. It sounds like the sensing parts in the door are going off and on.


... Frigidaire 24 in. PLDS9999CC Stainless Steel Built-in Dishwasher

8 years ago we bought a model 665 Kenmore Limited edition Stock #575-0 if you need that. A certified kenmore tech. has been out here 3 times with still no clear answer. The problem is when you run a standard cycle of 95 minutes it counts down to 78 minutes and stays at that time for about 45 minutes then stars counting down again till 42 minutes then stops at that time for about another 45 minutes then coutinues till it finishes the wash and drying cycle. It runs and sounds fine the entire time


Sounds like timer prob.would rec. replacing timer ... Dishwashers

Maytag mdb6601aww push normal wash button-- nothing happens. push other wash cycles, the lights flash about 30 times then stop-- then nothing happens. tried clearing codes. hi temp wash then heated dry , hi temp wash then heated dry. same problem. also tried normal wash then heated dry 3 times in 6 seconds--- same thing. also tried unplugging unit waiting 10 minutes with no luck. thanks


... Maytag 24 in. MDB6100A Built-in Dishwasher

I have a Whirlpool ADP6515. It's been working fine for about 2 years now but recently cycles are not completing properly, it can run for 30-40 minutes depending upon cycle. The start light is flashing a 4 times repeatedly, I think this happens when it moves from a wash to a pump cycle but not sure. We have to hold down the start button to force it to go to the end of the cycle and the the lights stop. If we do that we can then use the dishwasher the next time, but only after we force it to go to


While replacing the console board, the replacement should be of same version. The boards are using programmable IC. Hence matching the software version is a must. Only the manufacturer or his authorized provider can help regarding t ... Whirlpool Gold 24 in BuiltIn Dishwasher w Adaptive Wash Cycle 24 in Builtin Dishwasher

Our dishwasher (a Maytag - MDBH970AW) will not proceed past the intital intake of water. It has done this occasionally in the past, but with repeated attempts to start a wash cycle, it would eventually work and continue to work for some time afterward. However, in the past week, it will not go through a wash cycle. I have ran the water, prior to starting, to ensure that it is intaking very hot water. When it quits, I can push the start button again and it will go through the 2 minute drain c


... Maytag 24 in. MDBH970AW Built-in Dishwasher

I have a Frigidaire dishwasher that's just over 1 year old and I use it a couple times a week. I turned it on last night and went in another room. appox 30 minutes later my daughter came in and noticed the soap suds all over the kitchen floor, the inside was all sudzy. It was in the wash cycle so I turned it off just by opening the door for overnight and restarted this morning and after about 20 minutes (still in the wash cycle) the suds started oozing out so I that's where I'm at now. Thanks.


Hi,Someone squirted dish soap in there instead of regular dishwasher detergent...You will need to manually rinse out the soap and use the right soap...heatman101 ... Dishwashers

My frigidaire dishwahser was set to run a normal wash cycle and heat dry. It never ran, the soap is still in the holder and the lock beneath the heat dry option is lit. I'm unable to cancel or select any other options. I cannot get the dishwasher to run. Do you have a solution? I have tried holding down a number of the buttons in different combonations but still can't get the light to go out or start a wash cycle.


Looks like a number of things are happening.\015\012\015\012It would be easier if you can provide the model no. of your frigidaire dishwasher.\015\012\015\012I am assuming you have turned the mains power off and on. ... Frigidaire Dishwashers

Time to go, and washing cycle, stuck at 36 minutes. Switching off/on makes no difference. The cycle is stuck at 36 minutes to go


Replace the module ... Dishwashers

My Bosch SHE45M built-in dishwasher is suddenly taking an extra-long time to go through its cycles. On Regular wash it will countdown from 117 minutes to 31 minutes. When it hits that time it resets to 87 minutes, then counts down to 1 minute and will not stop. I have to hit the cancel-reset buttons for it to drain. I have tried to do a hard reset by cutting the power at the breaker for 20 minutes or more. I'm interested in potential parts and a description of how to fit it! Thanks in advance.


... Bosch SHE45M06UC Built-in Dishwasher

After starting the cycle, the dishwasher starts and runs normally for a short time, then the water drains out of the tub prematurely while the cycle is still going. The machine then runs dry until the cycle times out. At the next cycle and the process repeats. It started as a sporadic problem, but is getting worse.


You may have a faulty drain valve,the drain valve is under dishwasher there are two clips on each side check,with applance store for replacement part. ... Maytag 24 in. MDBH940AWS Built-in Dishwasher

I have a whirlpool gold quiet partner 3 n the cancel button won't go off n the normal wash button won't go off either. I can do a quick wash cycle on it but then goes right to sani rinse afterward n don't shut off itself it just keeps on going. Solution? Is there a reset for it because I have an air dry button but not a heated dry button so I don't kno if I should push sani rinse/air dry two times over as opposed to sani rinse/ heated dry or if there's a diffrent solution for it. This all starte


... Dishwashers

I actually don't know what type of Bosch I have. I know that is a problem, but maybe you can still help. It has a simple panel that says: Pot Scrubber, regular wash, quick wash, rinse and hold. When I turn on quick wash, sometimes it says 38 min. 45 min. 56 min. We want to keep it at 38 minutes and we don't know why it varies. If we have to open it mid-cycle, it switches to a higher cycle time. How do we set it for 38?


On a Bosch dw, it has a light sensor to sense soil in the water.. if the control feels that the water going through the sensor is not clean/ or clean it will add or minus time..one thing you can do is make sure that your drain line from dw to sink dr ... Bosch 24 in. SHU43 Built-in Dishwasher

Yes I have a whirlpool DU1345XTVB1 dishwasher. Just got in July. After each wash cycle the dishes are not dry. I have been using Finish gelpacs w/jetdry & also have a off brand drying agent in reservior to help dry dishes. The water temperature is set pretty hot & washer is draining good. I have tried checking wash cycle a few minutes into 1st cycle to see if water is in filling & heating. Didn't know if maybe heating element going out or thermostat not working? Thank you for your time.


<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-language: EN" lang="EN">Hi,<br />Check your heating element.. </span><br />\015\012<span style="FONT-FAMILY: 'Trebuchet MS'; FONT-SIZE: 10pt; mso-ansi-lang ... Whirlpool 24 in. DU1050SS Built-in Dishwasher

When trying to start the dishwasher, pressing the Normal wash button, the dishwasher gives a huge clunk and then it trips the circuit breaker. Upon resetting the breaker, I tried the next button over, which is Soak and Wash, and it seems to go thru the cycle fine. Another time I tried the Normal button, but put the left dial on Rinse and it started up, but it would clunk periodically and it seemed to have a 'hot' smell. I'm worried to use it - what could this be? Is there anything else I can try


Hi\015\012\015\012This is a very dangerous situation you must remove from the wall supply and desist from using, such a fault could easily make the casing "Live" and anyone touching it may be killed. You need to discover why this is happe ... Dishwashers

A few days ago the dish washer was running fine, maybe a single wash every day. Then, out of no were the logic seems to have left the machine. If you pressed the "normal cycle" button it would blink for about 30 to 45 seconds then the front panel would go blank. All LED lights would turn off, like it finished doing the diskes, never running a single cycle. I unplugged the machine to let all circuits reset, that worked for two days, two washes in that time. Today I'm back to a machine that will n


Your control panel is faulty and will have to be replaced. This is the main brain of the machine. Normally when a cycle doesn't start the timer is bad, but when your control panel doesn't do anything, then it is faulty. ... Dishwashers

I tried pressing the normal wash heat dry, normal wash heat dry several times, yes it reset my washer, but after a few uses, sometimes it will only run 5 minutes, sometimes it will run the full cycle. Then the green light starts blinking again. HELP!!!


... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

Our Frigidaire Dishwasher buttons stopped working. If we push normal cycle it will not select as well as other cycles. The last time it happened the maintenance guy came and turned it on and off and it started working again. That didn't work this time. We still can't select some of the wash buttons


You will have to replace that selector switchhttp://tclaundryrepair.com/ ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Blinking clean light on my Kenmore 665.17052400 7 times Did the "reboot" normal wash,heated dry sequence which made the machine work for a while. then it would go less times in between needing to be "rebooted", now it will not go through a cycle w/o the clean light blinking even following a reboot. what is my next step? I have heard that this means the microprocessor will need to be replaced. is it even worth it?


No its about a buck forty but im sure you could do it your self ... Dishwashers

The cycle doesn't seem to stop correctly. I start a load. It doesn't seem to matter which mode that I start in, but it will count-down the time, but at the end it hasn't stopped running. I've cleaned out the filter and the trap below. I've ran vinegar through a cycle. I've cleaned all of the spray arms. It doesn't seem to advance out of the wash mode. There is still some suds at the end. I have to end the cycle by canceling and draining it manually, then run a couple of "rinse--9 minute" cycles


Hello,\015\012\015\012Based on your description I'd say the issue is with the control. That is what I'd be looking for if called out to service the unit with the symptoms you've described. \015\012\015\012The issue is within t ... Bosch 24 in. SHU43 Built-in Dishwasher

Hi. Our DS603I dishwasher starts on the Rinse cycle on its own - it beeps, red light flashing and no water entering the tub. It does this even if it is open. Similarly, when we try to turn it on to do a normal or heavy cycle, it starts (making quiet a loud noise) and then goes to the Rinse cycle, beeping, red light flashing, no water going into the tub. The pump wheel is turning. We can't find any blockages in the tubes. We have power-cycled it many times. Please help!


Dishwasher Repair Guide: How To Fix a Dishwasher - ACME HOW TO.com\015\012\015\012\015\012\015\012 ... Fisher DS603W / DS603B / DS603I Dishwasher

I have a Rebadged Siemens dishwasher model no. SE6TIE1GB / 13 TKD 795 / 2. When turning on, the dishwasher makes the "normal" noise of washing but after less than a minute it stops and refuses to wash anything. Ive tried pressing the reset button but no help. Worth mentioning, the night prior to that, I switched on the dishwasher before sleeping and when waking up at 5am, it was still washing so I manually turned it off and opened the door to find some water at the bottom of the tray.


... Siemens Dishwashers

Blowing fuse... We've replaced the overheating fuse located in the control board area about 5 times. It has just blown again after using the dishwaser one time--before it would go about a month before blowing the fuse. It seems to get about a few minutes away from completing the wash cycle and does not complete the draining process. Help!! We don't know what to do next--replacing the fuse is costing about $15 each time, before you know it we could have bought a new one! Thanks for the help. Ti


Tim, this blown fuse issue was pretty common on this model. Whirlpool, which made this model came out with a fuse kit that included a terminal and heavier guage wire to eliminate this problem. It just splices right into the control board, easy job. T ... Kenmore 17024 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1953 seconds