Having problems with your Bosch 24 in. SHU6802UC / SHU6806UC Built-in Dishwasher ?

I will continue to try to drain and does not stop. I reset it and use papertowels to remove watter from tray under pump I will start again but will eventually go back to the same situation of trying to drain but never getting lower than 1 minute left


Answers :

Two possible areas of suspicion are the drain pump / drain filter that can be faulty or clogged resulting in lower pumping action in the said time . A good cleaning of the pump/ pump filters and drain filters can help to improve the drain pumping.
\015\012Also the drain cycle is controlled by the controller board and unless there is an error in the program the board must be working well. So remove the board and reconnect check for loose connections or faulty sensor.
Repair Help & Product Troubleshooting for Bosch 24 in. SHU6802UC / SHU6806UC Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I will continue to try to drain and does not stop. I reset it and use papertowels to remove watter from tray under pump I will start again but will eventually go back to the same situation of trying to drain but never getting lower than 1 minute left


Two possible areas of suspicion are the drain pump / drain filter that can be faulty or clogged resulting in lower pumping action in the said time . A good cleaning of the pump/ pump filters and drain filters can help to improve the drain pumpi ... Bosch 24 in. SHU6802UC / SHU6806UC Built-in Dishwasher

Gets to the end of the cycle (1 minute left on countdown) and just keeps running, does not start the "dry" mode. will run until i open it and when i shut it it goes 13 minutes left on the countdown but then gets stuck at 1 minute again. does not drain. has been doing this awhile, but until now it would simply finish the cycle when i opened, closed and reset it. now it just gets stuck again.


Hello,Welcome to FixYa.Based on your description ... Bosch SHU5315UC Dishwasher

A small cap fell down into the drain area on my Kitchenaid dishwasher. I removed the lower washer arm trying to get to the drain area. I could not figure out how to get to it, but now I have another problem. I can't get the washer arm back on!


Grab the center nut with pliers and pull up on it while spinning the spray arm. ... Dishwashers

I am trying to install a new Maytag MDBH945AWB Dishwasher and have to run the drain hose under the machine in order to get it to the sink. Each time I try to use the hose that comes with the machine it snaps in two and breaks. I have tried to look for a replacement hose that would stand up to the abuse but all I can find is the original. Is there a replacement I can get that is more flexible than the one that comes with it? At this point I am rather embarrased about going back to Home Depot


Hi...home depot sells clear PVC hoses, They come in various lengths up to 100 ft. You can use hose clamps to connect it to the T-fitting. ... Dishwashers

My Bosch dishwasher, model SHE58C did not completely drain. We were eventually able to use the cancel cycle/drain procedure to get the machine mostly drained, but now all the lights are lit on the panel, and the count down display is 11. I haven't figured out how to reset. I have tried to hit "Cancel drain" and turn on the machine to get into diagnostic mode, but I can't figure out what the codes & light combinations mean because my model is not in any of the online sources I've found


I have managed to pick up typical diagnostic error codes for a bosch dishwasher - these are\015\012\015\0120 = No faults detected 2 = Heating fault 8 = NTC (temperature sensor) fault\015\0121 = Aqua Se ... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

How to diagnose? My Kenmore won't run. First it was flashing the clean light 7 times, so I figured out how to reset ("High Temp Scrub"/"Air Dry"/"High Temp Scrub"/"Air Dry"), but when I try to run a wash, it sounds like it's not getting water into the tub. When I checked it several minutes later, it was in "Cancel" mode, making a sound like it was draining (or trying to drain), then the clean light started flashing 7 times again. Clearly, the machine has something wrong but I don't know where to


Once this code goes off, it is not going to run. The module has picked up ths issue as you said. I would check the sensor first. You can make sure it is getting current by testing the circuit. ... Kenmore Dishwashers

Disposal plugged up and water backed up into dishwasher. Cleared disposal and dishwasher drain line. Checked around sump but dishwasher won't pump out. Sounds like pump is trying to run. I can blow air through the drain hose from the disposal and get bubbles in the water. Turned off breaker for 1 min. then tried reset. Can hear pump humming.


The pump is humming because its still trying to get all the water out of the unit. Deinstall the dishwasher and pull the entire dishwasher out from under your cabinet. Next step would be to disconnect the drain line from the drain pump and check to ... Dishwashers

HI dishwasher will not drain if i remove all the water will run thro cycle and stops with a couple of cms of water left have tryed to find filter inside and failed, removed sides and can see a pump on right hand side can turn impeller easily, is this the drain pump? if not how do i get at pump and or filter. is it possible that plastic chamber on left hand side could be blocked assume this transfers heat Robert


... Bosch 18 in. SRS55L02 Logixx Slim-Line Free-standing Dishwasher

I have LG dishwasher for 2 years now. Working perfectly until one day one glass gets broken during washing cycle. Immideatly we get EO error. We check possible reason of error in the manual then decided to try to fix ourself. We open bottom cover and drain outcoming part. Immideatly we discover a piece of glass that was preventing a small plastic piece to rotate. We remove that piece of glass. Put back covers and machine. We connected it back to outlets and run it. All was working again !!! This


In order to fix problem we disconnected dishwasher, put it on one of side, opened bottom cover - the one that is outside of dishwasher. We find out the part that is\015\012connected to the drain horse. We take of 3 screw and open that part too ... LG Dishwashers

My Maytag Dishwasher mdbd880awq wont finish a wash cycle. It will wash and rise then when there is 32 minutes left it wont drain and wont dry the dishes, It just makes a clicking sound. I have to dry the dishes by hand and then use the rise only cycle to get the tub to drain. The drain only doesn't work either


... Dishwashers

The problem started with it not draining correctly and leaving water in the bottom - my husband took it apart and found a bolt in the drain. He removed it and now it won't start. It appears to not have power to the electrical panel- we have reset the breaker several times - left the breaker off for 10 minutes thinking it might erase the memory - I've asked for instructions to reset and I keep getting info that is very far removed from this model. I know it has a protocol because a repair


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012\015\012The reset on your dishwasher is as follows, ( I can't locate your particular model number...but its madw be whirlpool so there are only a couple of possible sequences ) however depending ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

Hi there My Bosch Exxcel Dishwasher is tripping out the fusebox RCD and I think there is an earthing problem. It will run for 3 or 4 minutes and then the house alarm goes off and the cooker clock needs resetting! I have tried to look in the back but don't know how to remove the panels. I've tried tipping it to 45 degrees to see if there is any water in the innards but non water came out. I have no idea what to look for - and no manual to help me get inside the beast! Thanks in advance.


It will probably be the water heater element is failing and shorting out.\015\012\015\012Be careful as you do not want to electrocute yourself ! ... Bosch 24 in. SGS45E02 / SGS45E08 Exxcel Free-standing Dishwasher

The control board seems to be locked in the drain cycle. I have tried powering it down for 5 minutes by unplugging it. I have tried to run a diagnostic cycle, but the only thing I get is error codes C1 and P0.


Hello, Welcome to FixYa. ... Bosch 24 in. SHX57C02UC / SHX57C06UC Dishwasher

My dishwasher's lid is stuck down and won't retract. I have a Fisher and Paykel DD605 dishwasher, and I think I must have placed some dishes in there that were too big for it and the lid got stuck. It's now showing an F7 error and refuses to do anything other than beep at me. I've tried turning the power off and back on, but it persists with the error. Is there a way to get it to reset and retract the lid? I've read that in situations like this, when people get repair technicians to com


The error code f7 stating that "the communication time out error"this are all the reason for the error1.the motor control micro has crashed and is not responding to communication request.2.the hardware communication link from ... Dishwashers

There is food left on the dishes; the air tube is clear, think it must be the drain is blocked with food;; so removed bottom basket took off the middle plastic 'nut' and removed the 4 metal screws ,but really stuck on the next step. WE have been trying to get that darn screen-filter off to get to the place to clean out PLEASE help! THanks


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Dishwashers

Bosch logixx dishwasher sounds like its running continuously & will go through entire program but does not fill or wash. Filled it with hot water manually to try for air locks & it does drain out. Then continues to attempt to drain even while door is opened. My amateur guess is that its a float switch but can I get at it from the inside or from the back? If thats what it is. Hope you can help,thanks.John


... Bosch 24 in. SGS09L12 Logixx Free-standing Dishwasher

I got the pressure washer started - lots of smoke etc after not having used 3 years. I then poured in wrong oil to top it off - my brother's chain saw bar oil. DARN. After 3-4 minutes it started rattling and stopped. Can't pull the chord to get started. Did it seize the engine? I have drained all oil. Can I try using a cleaner, light weight oil to try to unlock it?


Nope! you have blown the seals and most likely the cylinder is full of water. You will need to take it to the repairer to have it cleaned checked and new seals fitted. $200 ... Karcher 1750 psi Electric Pressure Washer

Dishwasher is 2 years old. Top shelf dishes not getting clean even on on heavy duty and sani rinse cycle. All arms move freely,tried the 2 cups white vinegar in an open container and run cycle. I thought that helped but a few days later we are back to the same thing. No debris around drains. Tried loading differently. I have called for a repair person,but is there anything else I could check on my own?


Sometimes the holes in the arms get blocked up,sweetcorn,rice etc, this then stops the arm spinning and water being sprayed onto plates etc, unscrew it and run water through the centre hole and see what happens. ... KitchenAid Dishwashers

My GE Nautilus Portable dishwasher is leaking from the bottom, back left-hand side. Water is still draining from the drain line. Not sure how to disassemble to try to fix. Clogged line? Any advice?


... GE 25 in. Nautilus GSC3400J Free-standing Dishwasher

My tappan dishwasher is only 1 1/2 yr old and its not getting at least 1/2 of dishes clean. We have tried everything from changing to liquid soap, increasing water pressure at meter, not using while washing clothes. We used a dishwasher cleaner to remove calcium, and run hot water in sink before using. We know the wand, pump and drain are working. It is model TDB210RFB5 with 1.1A motor. Is the motor too small to clean dishes? I wish I could get my money back or exchange for an upgrade. Thanks!


... Electrolux Dishwashers

Draining problem Water left in dishwasher after end of cycle. Have a disposer, don't have a drain air gap that I can see. Tried to do a cancel/drain, showed 2 minutes ended and water still there. Disposal works fine. What is really interesting is that there is only two of us and at most we've only used the dishwasher thirty times since we had it. Of course- service plan ran out last year (July 07) Please help me. My name is Donna


There is a flapper in the drain hose just where the hose attaches to the pump assembly it has been know to get dislodged and cause a partial drain. With towels underneath hose remove drain hose and stick you finger in and see if it is free moving. ... Kenmore 24 in. 16539 Built-in Dishwasher

My dishlex globale 300 has a modle no that is dx300wa*02 the eco light and pump keeps running i have recieved advice to drain/dryout the kidney shapped over flow tray but mine doesn't seem to have one. i've taken off the bottom cover to get a closer look but still can't see it i've also tried tipping the washer on it's left side right side,backside and even upside down to try and drain the extra water but that has made no difference please help


Hi,\015\012Try taking the dishwasher out of its wall space and tipping it back and forth. Apparently the weight of water gathering in some component triggers the 'eco' function. Allow it to evaporate by waiting for few days. ... Dishwashers

My Dishwasher starts, then stops after 30secs and won't continue draining. Everytime I turn it back on it comes up on the steam cycle and won't go to any other cycle, drains for 30secs and stops again. Power light is flashing. Have tried holding power button down for 10secs with no effect. Filter is clean, pipes are straight-no kinks. How do I get it to start working again? It is a whirlpool dishwasher, ADP5550.


... Dishwashers

There is always water left in the drain at the bottom of the dishwasher, which gets sprayed back on the dishes so now my glasses have material on them and it gets baked on in the dry cycle....


Hi \015\012Dishwasher not draining issue usually occurs due\015\012to kinked drain pipe, clogged drain filter or drain pump. First make sure that\015\012the drain is not clogged and remove clogs if present. If ... Siemens SL85A705UC 24 in. Built-in Dishwasher

Kitchenaid kudso1flss1 is stuck in clean mode. clean light flashing on and off. tried to reboot by unplugging, when i hit cancel it goes into "empty water left" mode, then goes back to "clean" light flashing on and off. Can't get it to go back to "start ready" position.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012This is the first thing I'd try, based on your description. ( the clean light is an error code in this case ) On your control panel, If you press these buttons in sequence then close the door it ... KitchenAid Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1150 seconds