Having problems with your Bosch 24 in. SHU6802UC / SHU6806UC Built-in Dishwasher ?

My dishwasher stays stuck on '1 minute', and will not complete the ccycle or drain the water. I tried to do another cycle on it, and it went to 8 minutes, and then jumped backl to 13 minutes, and repeated that pattern until I finally just opened it to stop it. I had one visit from a repairman last week, who said it could be a number of possibilities, and he charged me $75 and said he would return in a few days when he was not so busy. I am fairly handy, and if I knew exactly what part to replac


Answers :

Make sure that the drain spigot is not blocked under the sink. Water has to pump out OK.\012Then the most likely fault is the release valve at the bottom of the heat exchanger. It jams because the plunger corrodes. To see to this you will need a competent Bosch technician like me.........after that the electronic might be crook , but I doubt it.
Repair Help & Product Troubleshooting for Bosch 24 in. SHU6802UC / SHU6806UC Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My dishwasher stays stuck on '1 minute', and will not complete the ccycle or drain the water. I tried to do another cycle on it, and it went to 8 minutes, and then jumped backl to 13 minutes, and repeated that pattern until I finally just opened it to stop it. I had one visit from a repairman last week, who said it could be a number of possibilities, and he charged me $75 and said he would return in a few days when he was not so busy. I am fairly handy, and if I knew exactly what part to replac


Make sure that the drain spigot is not blocked under the sink. Water has to pump out OK.\012Then the most likely fault is the release valve at the bottom of the heat exchanger. It jams because the plunger corrodes. To see to this you will need a comp ... Bosch 24 in. SHU6802UC / SHU6806UC Built-in Dishwasher

I have a Braun combimax 650--it is fairly new. It was working fine last time I used it, but this time, the dial that turns the machine on seems to be stuck. The little button for the pulse does work. I read the instructions, which said that this might happen when the machine overheats and to wait fifteen minutes, but it is definitely not an overheating problem and the last time I used it was weeks ago.I love this machine and now need to use it for quite a number of things--any help you can provi


... Braun K-650 CombiMax Foofs Processor FOR 110 VOLTS

Hello, We have a combination oven and dishwasher. Last week I filled up the dishwasher and after about 5 minutes a blue spark came out at the bottom and it cut the electricity off. Once the electricity was restored we started it again and after a few minutes it just stopped after filling up with water. It blew a fuse again but only one fuse this time and now doesn't switch on anymore. We have emptied all the water from the dishwasher and checked the filter, etc and wonder what could have gone wr


Hi, I contacted the Rosieres web site in France and sent a message using the link Contact Us. Here is the reply;Dear xxxxx,we advice you to contact:TELE MENAGER VIDEO SERVICE21 rue georges Doublet0610 ... Dishwashers

I have the dishwasher model number FGHD2433KF, I have noticed the last few times I try to run the short cycle that after a few minutes it jumps to 99+. What could be causing this and how do I fix it?


Sounds like the control board is having a communication error. Reset the unit at the circuit breaker and retry. If it happens again contact the manufacturer for a repair. ... Frigidaire FGHD2433KF Builtin Dishwasher

LIGHTS FLASH Hallo, I have a Indesit dishwasher (IDL 750) and the last few weeks there is a malfunction. After 15 minutes that the wash cycle 2) had started the dishwasher stops and the first and third wash cycle phase indicator lights flash, beginning from the right. Could you help me telling me the possible cause of this malfunction. Thank you in advance Fred Tourman Athens, Greece


... Dishwashers

During power scrub cycle which is the one we use most of the time the dishwasher stays at one minute fot a long time. the dishes come out clean and it finally does finish cycle just dont know why it takes so long on last minute of cycle for so long


It's just heating the water more ... Bosch 24 in. SHU43 Built-in Dishwasher

Takes more than 2 hours to complete a one hour cycle. Will sit on "1" minute left for the last 45-60 mins. If the door is opened during this long one minute the washer still has water in it and will reset to 13 mins remaining.


Hello,\015\012\015\012Welcome to fixya.\015\012 \015\012**What I`m about to share applies to Almost all Electronic control B/S/H/ dishwashers. That includes Bosch, Thermador ... Bosch SHU5315UC Dishwasher

Hi I have an hinari dishwasher model HDW41SL its about 5 years old it kept blowing the trip switch when I used it. I contact a local maintenance engineer that I use and he said the heater has gone. He has been looking on line and contacting his supplies but no one can supply one. Please do you know where I could get one. Thanking you. Estelle


... Dishwashers

My Bosch diswasher is hanging up in the cycle (at 102 mins. in normal cycle and 38 mins in quick cycle). I hear what sounds like a one second pumping of water into the sink area, a pause, and then another one second pumping of water, on and on, but there's no progression beyond this point. One possible cause: a few weeks ago someone turned off the hot water at the heater and another person tried to run the dishwasher. The dishwasher did not function because it could not get hot water. Perhaps


Hi\015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. To start with check the water inlet valve which is located\015\012behind the lower access panel on the left or right side of the Di ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Water from my disposal backs up into my hotpoint ($300-model) dishwasher. The dishwasher works fine otherwise. Is there a one way valve in the diswasher that is suppose to prevent reverse flow and/or is there other dishwasher motor problems which could cause this. Actually the Hotpoint Model number is HDA3600N00BB but this website did not recognize that model number so I put in the closest model number closest to mine.


If it's what I think, it's a simple fix. Does your dishwasher drain run along the floor of the cabinet, then up to the disposal? (my guess is yes). There should be an "air gap" between the disposal and dishwasher, this means when it comes out of th ... Hotpoint 24 in. HDA3400G Built-in Dishwasher

I have a Bosch dishwasher Model SHE58C05. This model has two displays, one on the front where you can see and one with the hidden controls that you can't see when the dishwasher is closed. The display in the front all of a sudden stopped working today. Top still works but I can't tell how many minutes are left while its during the cylcle. I did have to cancel a cycle this morning because I picked the wrong one. Is it possible I hit a strange sequence and somehow cancelled this display (wishf


If you check your user manual there is a section that will guide you through turning off/on the display screen. I have tried to include the link for Bosch manual downloader but their site is down at the moment. If you do not have your manual and ther ... Dishwashers

I changed the handel and switch assembly on my dishwasher because the old one was broke.The dishwasher does not turn on. It still doesn't work. it doesnt even light up. although one button does glow a little. Do you have any idea what it could be? the model number is MDBH955AWB


Check for line voltage at the door switches and from there to the control board thats to the right of the door latch switches for line voltage,if you have line voltages in all these areas then replace the front membrane push button control panel that ... Maytag MDB9600A Jetclean II Built-in Dishwasher

I have a Briggs & Stratton Pro 3400 pressure washer that I got new last year and used for maybe 5 hours and it worked great. Have had it stored since then with stabilizer in the gas (I didn't run it dry) and now it won't run for more than a minute or two without dying. A dealer said it was probably bad gas and I now know that even with the stabilizer I should have run it dry last year before storing. Everything is like brand-new including plug and air filter so it must be the gas/carberator gunk


... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

Hello I have a built in DCS dishwasher - width 24" heigh 35". It started smoking out the front and the repair man said it needs a new control board. Is that possible or should I buy a new one. IT is not a dishdrawer its a full dishwasher. the top rack is also broken. If I need to buy a new one - where from - new jersey area


Http://www.thefind.com/appliances/browse-dcs-single-dishwasheryou can purchase online from here... ... Dishwashers

About 20 minutes into a cycle (I usually use a rapid wash cycle-P3) the machine makes a loud clicking and grinding noise that lasts for about 1 minute. Any ideas what this could be and how to remedy the problem?


Danby customer service told me that it was built into the machine. The machine would shut off for about 15 minutes after that loud noise occurs. Then would finish the cycle after that point? Got infants, buy one of these products! LOL ... Danby DDW497W 22 in. Countertop Dishwasher

Blowing fuse... We've replaced the overheating fuse located in the control board area about 5 times. It has just blown again after using the dishwaser one time--before it would go about a month before blowing the fuse. It seems to get about a few minutes away from completing the wash cycle and does not complete the draining process. Help!! We don't know what to do next--replacing the fuse is costing about $15 each time, before you know it we could have bought a new one! Thanks for the help. Ti


Tim, this blown fuse issue was pretty common on this model. Whirlpool, which made this model came out with a fuse kit that included a terminal and heavier guage wire to eliminate this problem. It just splices right into the control board, easy job. T ... Kenmore 17024 Built-in Dishwasher

I would like to purchase a Moyer Diebel U/C dishwasher for residential use. I have the option of purchasing a used dishwasher - it could be one of three models. Which one is the model he is trying to sell to me? 1. 501 HT 2. 501 HTN 3. 501 LT the owner states the voltage is 120/208-240 and heats between 150 f and 180f.He notes there is a 4 ft. cord at the back without a plug on the end of it but the model is rubbed off of the serial number tag.There are three switches on the lower right hand co


The way you mentioned the unit have a 4 ft. cord at the back seem like a 50l LT the best way to determent is open up the bottom plate and see whether there is a booster tank in the right hand side. \015\012Hope this can help you. ... Moyer Diebel 24 in. 501HT Built-in Dishwasher

The slide on the upper basket keeps falling out. It's been fixed twice but doesn't hold. The second repair man who put the slide back in the rollers said he couldn't see anything wrong with it, but it still didn't hold, so he called your tech dept. who said they had roller and slide kits at a total cost of $66 for this model. The slide kit had a new part number but the tech department didn't tell the repair man why they'd changed the part. The roller kit was one for dishwashers the sides o


One option is installing stainless steel washers on the rack supports that screw into the side of the tub. The rack falls down because there is too much "slop" with the rack...a couple small washers to space them tighter normally does the trick. ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

The last time I used the pressure washer was running fine. A few minutes later I tried to start it up and could barely turn it over. I removed the recoil and could turn it a little easier backwards. The motor is a Honda GC190 on a karcher pressure washer and has 20 -30 hours of running time. Thanks Clint


... Karcher 2500 PSI Pressure Washer

Hi I have a dishwasher Maytag Model No DWU 7400 BAE and Serial Number is : 26294990 MK I would like have Get a user Guide for that. Is it possible to send it to me in french or in english ? My email is : [email protected] amd my adress is : Mourad Mlih 35 Micheline Gatineau (Qu?bec) J8T3G2 could you please send me the phone number of the support service. Thank you.


... Maytag Dishwashers

I have a Troybuilt pressure washer which has a Honda GC160 engine. The engine starts easily but quits after about a minute. One pull and it re-starts, then quits in a minute....... This goes on for as long as I want to keep re-starting it. Anyone know what it might be? I pulled the carb off and blew out all of the various ports I could find. I did not remove the carb adjustment screws as I have not had any luck getting them back in place during previous problems with other gas engines.


... Karcher 2500 PSI Pressure Washer

I have the dishwasher model number FGHD2433KF, I have noticed in the last few that I have used my dishwasher no matter what setting I push after a few minutes it jumps to 99+.... Example a push quickwash and start it, the time that shows on the screen is 50, it counts down to 49 then it jumps to 99+. Every setting I originally set starts out at the right time that is listed in my book but then after a few minutes it jumps to 99+. Do I need to call service. I purchased the dishwasher in May of


... Frigidaire FGHD2433K 24 in Builtin Dishwasher

Blown Motor DW is about 16 months old. Started making some real bad noise. Lasted about a minute and then had a death howl. Called in repair tech who says motor is blown. $399 for repair which includes $125 for the part. I've rebuilt car engines, so can probably replace a DW motor. Any insight on how to replace the motor? is it worth paying 275$ for labor? Just bugs the hell out of me paying $400 bucks for a repair when i can get a new one for $450.


I haven't changed that particular brand of dishwasher motor, so I cant give a step by step, sorry. I do know the other brands it is optional to get the motor alone or the motor with the pump assembly attached, so you may want to ask abo ... Maytag 24 in. MDBH950AWS Built-in Dishwasher

I have model number KUD 101TJBL0. I have spent about 300.00 on repairs. It keeps blowing the thermal fuse. I have had it replaced sev. times. My repair man has given up on solving the problem. I did read on another website that you need to replace the wiring kit that comes with the fuse. Me service man never did that and when I asked him about it he said that is not the problem and would not replace it. So, before I just scrap my diswasher and but a new one I thought i would order another fuse k


Hi,This applies mainly to Kenmore Dishwashers with the model number\015\012665.15835791 but also to any Whirlpool or Kenmore dishwasher with an\015\012electronic display. There are several possible trouble makers on this\015\012dishwasher ... Dishwashers

My SHE43 Bosch DW will not pump the water out after the last cycle. The service guy said the Door latch was broken and replaced it. but the problem still exist. He now say that the water lines are freezing up because the DW is on an outside wall. The Thermador DW that was replaced never had this problem during the 15 years it was located in the same place. Could this be a bad design? Help!!!


I\015\012\015\012\015\012\015\012 the water doesn't drain from your dishwasher, check these:Drain line/air gap ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0734 seconds