Having problems with your Bosch 24 in. SHU6802UC / SHU6806UC Built-in Dishwasher ?

Bosch My bosch dishwasher shows an "F" on the display when started. It sounds louder than usual but the cycle doesn't start. I made sure there were no obstructions, debris, etc but no help. Thanks.


Answers :

F is fill fault to much or not enough water or water in the sump white plastic base the f code will not go away until you solve the problem when the f code shows up the drain motor will run all of the time
Hi
\015\012Bosch diswasher indicaates "F". I've taken off Aquastop, checked water flow (good), cleaned little filter (it was clean) and reconnected as per instructions in manual. Still no go. I understand that it means "filling" fault. Where else can I check?
Repair Help & Product Troubleshooting for Bosch 24 in. SHU6802UC / SHU6806UC Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bosch My bosch dishwasher shows an "F" on the display when started. It sounds louder than usual but the cycle doesn't start. I made sure there were no obstructions, debris, etc but no help. Thanks.


F is fill fault to much or not enough water or water in the sump white plastic base the f code will not go away until you solve the problem when the f code shows up the drain motor will run all of the time ... Bosch 24 in. SHU6802UC / SHU6806UC Built-in Dishwasher

BOSCH SHE43 Dishwasher My Bosch D/W makes a loud high-pitched squealing sound at the beginning of the cycle and for a few seconds intermittently while running. I have checked and cleaned the filter, made sure there are no obstructions in the bottom and I am stumped. I have only had it a little over 2 years, spent a small fortune on it and really hope it isn't something super expensive. Does anyone have an idea of what the problem could be?


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012Based on your description...as soon as you said "loud high-pitched squealing sound"...is where I knew what you`re talking about.\015\012\01 ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

I have a Bosch SHX98M dishwasher and the top arm will not rotate. I can see water coming out of the holes when open during a cycle and I have made sure there are no obstruction for the arm or anything stuck in the arm feed line. I just had a technician here who was at a loss and did not think the pump was bad since alot of water is being pushed around inside. The bottom arm works fine.


... Dishwashers

I have a 13 month old Bosch SHE58c dishwasher. The pump runs constantly and will not refill the tank. There are no error codes thrown on the control panel, but not sure there are error codes for this model - the manual doesn't mention any. So I have removed the side panel and can see the bottom pan is bone dry and I made sure the overflow drain switch was not bound and operates freely. Is there some type of reset button or other task I can perform to continue troubleshooting this problem? Repair


I have exactly the same problem. Turn on the machine and it just pumps and pumps, door controls do nothing. According to the technician who came and looked at it the problem is a bad control board. He ordered the part and we are waiting on it. ... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

Our bosch dishwasher runs but no water is spraying on the inside. Is there a water filter clean out or is there a water pump that might be broken? I checked the line coming in and it isn't plugged. I made sure where the stainless line goes into the electric valve that it wasn't plugged to that point. I could see anywhere else to check if it was plugged. I figure there has to be a water pump, but I guess I'm not sure of that either. Thanks for any help..


Hi, welcome to Fixya. \015\012 \015\012By the description you've provided, it sound's like the wash motor is either seized or just stuck, let's hope it's the later. \015\012 \015\012Bosch had issued a service tip about this ... Bosch 24 in. SHE43C05UC Stainless Steel Free-Standing Dishwasher

Hi: I have reviewed the forums and tried to fix this issue. Have a Miele G2120 dishwasher that at the end of the cycle - the three (rinsing, drying and end) orange lights begin blinking in harmony. I have removed the triple filter, and two plastic parts to the impeller and made sure all was free of obstruction. I then pulled it out removed the drain hose from in-sinkerator; removed the water line and checked for obstruction. When it gets into this condition - the majority of water drain


Hi The issue seems to be with the float switch assembly that is bad and should be replaced. Float assembly is found inside the dishwasher's tub, on the bottom. The water that ... Miele Inspira Series Dishwasher w/ 6 Programs and 5 Temperatures - G2120 / G2120BL - Blac 24 in. Built-in Dishwasher

Bosch Dishwasher I have a stainless steel Bosch dishwasher, I made the "mistake" to try to see if I could fix the jammed handle from the door. Unfortunately, (did not realize the top panel comes off without opening the entire door). I removed the screws from the door frame (Inside panel), and the door springs/latched got loose. I would like to put it back together, but I dont have any diagrams on the door to make sure all parts are in place to put the door back together. I have been havin


Hi ED,\015\012\015\012It sounds like a real problem here. If the springs are still in one piece, my best guess is to to remove the springs from the door. Then attach the springs to the dishwasher body first, then reattach the spring to the door. Not ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

I have a Bosch SHU9915UC/U11 dishwasher, installed in 2002. Recently, our hot water heater had to be replaced, and we were without hot water for five days. Air got into the hot water pipes, and dried out all the debri in the lines. When we got the new hot water heater going, all of the sediment in the pipes ended up in the in-line screen filters in various appliances (clothes washer, etc.). I have cleaned these out, and these appliances are fine. Since then, the dishwasher has been shutting


All inlet valves have a screen built into the valve itself,shut off the water remove the entire valve and you will be able to see built in screen,if you flush out the debris from it and re-install the valve it should work fine.  ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

My frigidaire dishwasher (FFBD2405KB) is not working... when I press the wash button, it will blink, but nothing happens. I've tried it on all settings, but nothing works. It's obviously getting power since the lights are working. I've cleaned the drain thoroughly and made sure there were no obstructions. Any ideas?


... Frigidaire Dishwashers

Salt Light Cannot get the salt light to go out. Had some problems with a crystaline Deposit on the left side of machine. we checked the inside of the dishwasher and made sure all was clean etc. After that the light wouldn't go out. Had machine serviced. Turns out we were using too much diswashing powder Only need to use about a Teaspoon (heaped) for a wash not the recptacle full.


The sensor in the salt chamber isn't reading properly. Try descaling the machine with solution and restarting. ... Miele Dishwashers

I have a GE Dishwasher: PDW8480JO1SS and it does not fully drain when I run it. I disasembled it and after finding a carrot deep in the pump area thought I had fixed it, but no luck. I also made sure there were no obstructions in the drain out to the disposal. Tee unit is about 6 years old. I don't know if I need to replace my pump or motor? Can you help? Thanks, Mark


... Dishwashers

LG Dishwasher Model LD-1403W gets stuck and stops on rinse cycle leaving water in bottom of machine. I have stripped it down and emptied it, made sure filters etc are clean but to no avail


LG Dishwasher LD 1403W. We have cleaned it and when it gets to the heating cycle after running right through to nearly the end, it trips all the electricity and stops everything. Its only 3 years old and hubby thinks its the heating element but betwe ... Dishwashers

My Miele Platnum dishwasher is not working. It is flashing "intake/drain" When it begins instead of the normal hearing of water moving around you just hear a humming. My husband and father took out all the filters/baskets etc and made sure everything was cleaned out. They checked the hoses. After that it seemed like it was going to work because it started to cycle normally but now it is flashing again and this time there was water standing in the bottom of the dishwasher. Any thoughts?


Most common faults with dishwashers is a drain fault. Check for any kinked hoses and check the drain spigot under the sink where the drain hose connects into the u bend. Usually this is where food gets trapped due to the spigot not being drille ... Miele 23 in. Novotronic G841 Built-In Dishwasher

Bosch Exxcel Diswasher SGS43E08GB/43. Top spray bar won't spin. All arms, spray holes, ducts, filters, etc are clean and free from obstructions. Water comes out of the holes on the top bar but it won't spin. Water pressure inside the machine with all the bars and ducts removed seems good. Bottom bar works fine. Any ideas please?


Try starting the washer, then opening to door and checking the water level in the bottom of the machine, as far as I know, there should be enough water there to disolve the tablet when it sits in the bottom. if not that much, bung in a few cupfulls a ... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

My kenmore dishwasher, model 665.16473300 has stopped working. Now the lights just flash at the Smart Wash, Normal Wash, and Cancel. I've reset the power and it just comes back. I've taken the drain area apart and made sure there are no obstructions. The buttons seem to respond, as after I reset the unit (breaker), only the Smartwash button is flashing. I push cancel and then it starts flashing. So I think the buttons work, but it's locked up.


IS THE WATER TURNED ON TO THE DISHWASHER ... Dishwashers

Good day after the power is turned on to my brand new kudc03fvss dishwasher, nothing happens. have made sure that the power supply is ok and that the door is properly closed. there is 115 volts at the circuit board inside but nothing happens. no lights, no response to switch etc. just dead. need some advice


You said your getting 115 volts and that is across the power wire and its neutral not a power and ground.. i had a case like this last week and when i got there the unit had power if tested from black to ground but not from black and the white neutra ... Dishwashers

My Bosch shu 42 just stopped cleaning. there is soap residue also on the dishes. It doesn't seem to be getting really hot water. We cleaned the filter and made sure it was loaded correctly.


When the heating element fails on dishwashers, the wash cycle water can not be heated high enough the activate the DW detergent powder.Replacing the heating element should fix you right up.Also, resist the temptation to switch ... Dishwashers

After moveing to a new house our Bosch dishwasher is not washing the powdered soap out of the holder, then bakes on a nice film of soap on all of the dishes. When the cycle is done a fairly solid ball of soap is still in the tilt-out soap holder. I have looked for obstructions and cleaned out the screens but still no luck fixing it. We think the soap holder didn't used to end in the tilted out position but we can't remember for sure.


Its not soap, its calcium build up.The problem is hard water. There is a new product out called the dishwasher filtration system. It filters the water before it enters your dishwasher. It works amazing and has a money back guarant ... Bosch Dishwashers

Maytag MDB5000AWW started making noise when cleaning. Bottom arm working , but water isn't pumping with much force. No water coming out of top hole (removed arm to make sure there is no obstructions. Checked down to the impeller (didn't remove), and didn;t see any blockages, etc.


HI\015\012Motor malfunctions usually call for service by a professional. There are three main causes of motor failure: lack of lubrication, a defective motor switch, or worn or frozen bearings. A humming sound can be related to a burned-out mot ... Maytag Dishwashers

Our washer had been woring fine earlier this afternoon. After a short (about 10 minute) break, it developed only hose pressure. We disassembled the nozzle, figuring there might be some obstruction; also made sure the hose wasn't kinked. No luck even though the motor is apparently running fine. It's about one year old. What do I do now?


Can you see my posting: "Karcher - no pressure", also my own comment where I describe my later technical findings - mashed up gearbox. Could it be the same problem as yours, where the motor sounds to be running just fine but there is simply no press ... Karcher PSI Electric Pressure Washer

I have a Bosch SHU 3030 dishwasher that made a loud clicking noise and then stopped mid cycle. There was water at the bottom of the washer that I scooped out. I checked the filter and cleaned out any debris. There appears to be no power to the dishwasher. I spin the control dial and nothing happens; no lights, no sounds. The circuit was not flipped.


Pull the bottom kick panel and check the connections on the lower right, where the electric wires come in. Trip the breaker first, to be safe. ... KitchenAid 24 in. KUDI01TJ - Multiple Color Built-in Dishwasher

Bosch SHE44c getting a E6 code????Just finished E1 code by re-soldering the board and the first wash after fixing that error, I get an E6 code and it did not drain. During the repair of E1 code, I cleaned all hoses out and made sure I had no problems...What is the troubleshoot to search for E6 code?


Thanks, that perfectly nailed my problem. Bad / burnt solder joint on a SHX45P05UC/57 model. A little solder, and it may last a while. But next it fails that way I can order the motherboard without even opening it up. ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Hi There I am having a problem with my Candynova CD122J Dishwasher, The problem is the water is not emptying out of it, I have checked and cleaned the filter and made sure there was not cutlery etc caught in it, Have you come across this problem before or would you have any help on this?? Any help would be well appriciated. Regards, John 00353852113372


Water pump could be out could be restriction in the hose that runs into the sink drain ... Dishwashers

Bosch sgs5312gb/12 not draining, no obvious obstructions


... Dishwashers

Stuck in cycle? Bosch SHE4am16uc


... Bosch Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0863 seconds