Having problems with your Bosch 24 in. SHV66A03 Built-in Dishwasher ?

NO WATER GOING INTO DISHWASHER - Bosch 24 in. SHV66A03 Built-in Dishwasher


Answers :

Hello,

Welcome to FixYa.

Based on your description, "NO WATER GOING INTO DISHWASHER"...and to answer your question, the issue is likely with the inlet/water valve is faulty or clogged. Presuming you've ruled out the water supply is turned "on" and the unit is not stuck in the overfill/pumpout mode.

**To remedy this you will need to replace or clean out the valve**


This is what to look for..i.e.

e601791.jpg

As long as your model number is indeed correct, this info below will be accurate.

Original part is # 425458. It usually retails for about $20 - $30USD at places such as "searspartsdirect.com" "repairclinic.com" to name a couple, if needed. They may be available at your local brick & mortar parts depot/vendors.

**Before attempting to repair the unit please turn off the power and the water supply to the dishwasher...safety first**


If you remove the lower kick plate/toe panel, you will see the inlet valve to your left...


i.e.

7d9ad1d.jpg

Replacing it or to check for debris in the filter/screen at the inlet is pretty straight forward. Here`s how...

1) undo the water line. ( here you can visually inspect the screen in the valve...if nothing noted, you'll likely need to replace it as follows )

2) Remove the two #20 torx screws fastening it in place.

156e176.jpg

3) the feed tube to the machine at the back of the valve and swap it with the new one.

5937279.jpg
and

dd52c6a.jpg
Once the new one is in or it's all clear you should be good to go.

Let me know if you need any further assistance, otherwise good luck.

Thanks for visiting FixYa.

Regards,


Macmarkus :)

Repair Help & Product Troubleshooting for Bosch 24 in. SHV66A03 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

NO WATER GOING INTO DISHWASHER - Bosch 24 in. SHV66A03 Built-in Dishwasher


Hello,Welcome to FixYa. ... Bosch 24 in. SHV66A03 Built-in Dishwasher

Water is not going into dishwasher - Bosch 24 in. SHU43 Built-in Dishwasher


Check the inlet tap is turned on, it may just be a trickle of water going in have a listen, if so its a dodgy solenoid valve not opening. power off and unplug then follow the inlet pipe into the appliance and there you will see a valve with two wires ... Bosch 24 in. SHU43 Built-in Dishwasher

I have a ge profile quietpower 7 dishwasher. its built in.cannot find manuel and cannot find the serial number anywhere on the dishwasher..i need either your help with serial number or help with why water will not go into the dishwasher. motor runs water decided it wont go in. one day worked perfect and next day stopped working.


Hi\015\012\015\012This is often caused due to the fill valve. You can ... GE Dishwashers

Bosch Dishwasher My 8 year old Bosch is not draining. It will not go past 1 minute on the rinse cycle, and 13 minutes on the regular cycle. For the past few weeks I have noticed a lot of bubbles in the bottom of the dishwasher after it is done, but it was draining. Now it's full of water and will not go past the 1 minute mark. I need to fix this, I can fix this, I just need some expert advise on how to do this myself. Thanks!


What is the model #?... there are 2 buttons when pushed together it will drain the water out..try the button to the left next to power scrub... and economy...hold the 2 buttons for 3 sec. you will hear you drain pump running.. if you don't hear any ... Bosch 24 in. SHU43 Built-in Dishwasher

My trusty Bosch s510 Dishwasher which has been going strong for about 17 years (at least) has just decided not to empty itself. I noticed the bottom was full of water after a wash. I emptied all the water out by hand and presuming there is a blockage in the drain tried using a plunger to unblock it. I have since put it through another cycle and half way through water started leaking out of the front. At the end of the cycle the bottom of the dishwasher was again full of hot 'soapy' water. If th


Same problem, so went out and bought a new bosch. Problem with the S510 was cured by lubricating the pump out motor bearings with a squirt of WD 40. If you don't know which pump, follow outlet hose to pump outlet.Les ... Bosch Dishwashers

I have a Bosch dishwasher model #SHU3032UC/U12 It is not pulling water from the water pipe to wash the dishes the motor wants to go thru cycles. It starts to pull the water by the sounds from the sink but no water gets into the dishwasher.


Hello. When no water is entering the dishwasher, there are two parts to check. \015\012Water-inlet valve\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012The water-inlet valve lets water enter the machine. If this ... Bosch Dishwashers

I have a Bosch SHU9915UC/U11 dishwasher, installed in 2002. Recently, our hot water heater had to be replaced, and we were without hot water for five days. Air got into the hot water pipes, and dried out all the debri in the lines. When we got the new hot water heater going, all of the sediment in the pipes ended up in the in-line screen filters in various appliances (clothes washer, etc.). I have cleaned these out, and these appliances are fine. Since then, the dishwasher has been shutting


All inlet valves have a screen built into the valve itself,shut off the water remove the entire valve and you will be able to see built in screen,if you flush out the debris from it and re-install the valve it should work fine.  ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Bosch built in dishwasher shu4302uc The dishwasher appears to run through the cycle but the cycle keeps running. I have checked the screens and they were clear. I have a Bosch Dishwasher SHU4302UC and I can't figure out how to cancel the cycle it's in. It keeps running and running. It pumped all the water out and the LED indicator are lit for the rinse/dry.


There is a recall on the control board of many of these models. I have written a guide to help. It is here. Look for the phone number near ... Bosch 24 in. SHU43 Built-in Dishwasher

Frigidaire fdb1500lsfo built in dishwasher. Have had for maybe 3 years. I push the start button, and it starts like usual, filling the tub with water. After filling, it will not do anything for about 5 mins, where then it drains. It seems to go through the whole wash cycle, but after it has pumped the water out. Dishwasher steams all of the dishes, but there is no water in it to wash them with.


... Frigidaire FDB1502RG Built-in Dishwasher

I have a Bosch Dishwasher, Model Number SHX46L, Serial Number 860200524 that is no working properly. After running a cycle, it did not pump out all of the water, though the water is very clear, and the dishwasher does not display that there is any electricity going to it. I have verified the is 120 Volts AC at the appliance junction box. However the dishwasher will not turn on, and no lights will come on? Do you have any suggestions? I would appreciate it if you would let me know what you


... Bosch SHX46L1xUC Dishwasher

Check water indicator on BOSCH dishwasher - Bosch 24 in. SGI43E05GB Built-in Dishwasher


... Bosch 24 in. SGI43E05GB Built-in Dishwasher

Shu 3030 bosch dishwasher not getting water - Bosch 24 in. SHU43 Built-in Dishwasher


... Bosch 24 in. SHU43 Built-in Dishwasher

I need to winterize the built-in Kenmore dishwasher in a mountain cabin where winter temperatures will drop below freezing. The unit is at least 10-15 years old, but I don't have the model number handy. My approach to the cabin water pipes in general will be to gravity-drain them and then blow out remaining water by adding and releasing air pressure. RV antifreeze will go into all P-traps. When it comes to the dishwasher, my plan is to remove the drain hose from the P-trap and drain it as mu


In order to get the water out the best thing to use is a wet dry shop vac and attch it to the end of the drain hose on either your dishwasher or clothes washer this will remove any water in the drain pumps.As far as RV anti freeze being added not sur ... Kenmore Dishwashers

My Bosch dishwasher (SGV57T03GB/08) is draining and filling with water but none is being let into the main pump. I can see water going into the side reservoir but it doesnt seem to be let into the main pump area - any ideas on what is not working? Dishwasher tray is dry and float switch is not stuck.


... Bosch 24 in. SGV57T03GB Built-In Dishwasher

Where can I get the instruction manual for a Bosch Classixx Dishwasher SGS53C12UK? I have bought a second hand dishwasher that has only been used for 6 months. The programme works fine but when I go to use it again - check water shows on the display. I have to tilt the machine back as water is stored at the base of the machine, surely this is not normal? It there a simple solution to this or alot of cost involved with a new part? Any help would be much appreciated. Thank you.


... Bosch Dishwashers

Inlet water valve dishwasher bosch testing - Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher


... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Bosch dishwasher does not spray water - Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

I have a built-in Bosch dishwasher SHU 4302 UC. It no longer drains the water out at the end of all the cycles. I have tried everything mentioned in the booklet (make sure water is hot, use the jet-dry stuff, make sure outflow hose doesn't allow water back in). I have to siphon out at least a good bucketful of water. (Also, only the regular wash cycle works, which is fine with me.)


The problem is a solenoid on the bottom of the unit. It is a small black cylinder next to the pump. It operates the valve that changes to the drain cycle. You can probably order one from Bosch ... Bosch 24 in. SHU43 Built-in Dishwasher

Dishwasher i need help either installing for troubleshooting my 18' portable frigidare dishwasher. when the dishwasher is turned opn and it starts to fill the water flows out of the bottom of the machine what is the problem and how dod i fix it is it the hoses ? it also hooks up to the sink it isnot a built in dishwasher so is the hose for the draining need to go in the sink or does it hook up somewhere under the sink?


I would put the dishwasher on its back so you can see underneath to check the fill and drain hose to make sure there not damaged in any way to cause it to leak. if it all looks good under there return it upright and remove the front lower kick panel ... Frigidaire 18 in. FDR252RB Built-in Dishwasher

Bosch slimline dishwasher SRS560. Unit has had this fault for a while, now going a bit mouldy so keen to repair it. Displays following Symptoms 1) Firstly empty motor drains water. This appears to be fine as I can hear the gurgling of the plug. 2) Then takes water from inlet to fill internal tank. I can hear the water entering the tank, and tap pressure indicates that water is being taken in. 3) The unit then sits there and does nothing for 25 mins until programme ends. I've


... Dishwashers

My bosch excel dishwasher has the following fault: start the cycle, water starts to fill but then check water light comes on and it then starts to empty again. Pump then keeps going. I have checked the hose and even swapped it round with my washing machine one but this makes no difference. I have cleaned all the filters and taken off the cover to check the 'propeller' as sugested in the instruction manual. But no joy - check water light still illuminated and willnot continue with cycle. - Help!!


This unit im sure has a water flowmeter that measures the water intake.. if this cannot read then the unit shuts down to avoid flooding.. \015\012it needs replacing... it is attached between the valve and the side tank or attached to the tank d ... Bosch Dishwashers

I have a problem with a bosch dishwasher i put in a kitchen 10 years ago. knob on left side buttons on right , stainless steel interior. i dont think client has ever used it. he must have put in new disposal but did not clear knock out. he went to use it with regular dish liquid.it started to leak and foam. he left me a note to look at it. 10 hrs later its still running and water is everywhere. i disconect from disposal and pump water into bucket but now can not get water to go in to it. tried b


First check that the valve under the sink is turned on sorry have to put this part in next thing to check would be the inlet water valve and assure that you do have power going to the valve if you dont then you would look at the float switch as the p ... Bosch Dishwashers

I have a Bosch integrated dishwater that is just over 2 years old. It has suddenly stopped working and the tray at the bottom is not emptying, although you can still hear a buzzing sound. The cycle does not go beyond this point. I have emptied the tray of water and the dishwasher will start again, and pump water in, but it then stops, as though it is not able to pump water out. Does anyone know what this is? Could it be the pump? A blockage?


... Bosch 24 in. SHU43 Built-in Dishwasher

My Bosch dishwasher has several problems: 1) Water doesn't completely drain out and dishwasher kind-of smells when I open it -- I do keep the filter very clean. 2) The dishwasher takes HOURS to go through one load, no matter what the time says on the display and no matter what type of cycle you choose -- quick, delicate or regular. 3) The red display often displays something that looks like "2h" at the beginning of the cycle. 4) The place where you put the detergent doesn't shut.


Hi Kathryn .I think you have a defective pressure switch. The pressure switch is located near to the drain pump, and the device is used to determine when water had been drained completely.Also check the floater switch located ... Dishwashers

Installing a built-in LG dishwasher; got everything ready to go, but a problem with the hot water line coming in. It is barely long enough to reach to the front where I've installed the elbow. Since I have to back the dishwasher in to the 24 in. hole there is no room for error in terms of not running over this hose with the bottom of the dishwasher. Any tricks to handling this situation?


Hi, best way would be to install a "spring" attached to the back of the dishwasher. The hose would connect to that and easily "pull-away" when moving or "pull-tight" taking up the slack. A much simpler method is to tie a piece of string to the hot wa ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2283 seconds