Having problems with your Bosch 24 in. SHX33A02 / SHX33A06 Free-standing Dishwasher ?

My Bosh dishwasher now runs well past the 105 minutes as stated in the manual, over three hours before I intervene. It gets stuck on the wash mode, it wont drain or rinse, just runs and runs in the wash mode (I know it's in the wash mode because when I open it up, theres suds inside). It will do the wash mode until I reset the wash mode to "Rinse & Hold". I appreciate whatever information you could provide.


Answers :

Hello, welcome to Fixya.
\015\012
\015\012The problem you're describing is unfortunately a common one with B/S/H/ built dishwasher's. That includes Bosch, Thermador, Siemens, and Gaggenau.
\015\012
\015\012Here`s the most likely reason why it has detected the error...

Even if your home water supply appears hot, it's not hot enough and must be heated by the dishwasher to insure a proper clean and dry. Most if not all manufacturer`s do this.

When it comes to your Bosch dishwasher the problem likely lye`s within`the electronic timer/control, specifically the heater relay solder joint. ( a faulty flow switch, ntc or heater can also cause this, but not very probable ). This is why it runs forever unless pressing the two buttons for "cancel".

To repair your unit It will require you to remove the control from the unit and then remove the control from it`s plastic housing and look for a burnt solder contact on the printed circuit board. This will be one of the pins from the heater relay, hence the unit sit`s just running on & on because it can`t heat to advance or until canceled.

**Further to this, if you or someone you know is proficient at soldering, a lot of times it can be remedied by simply repairing the solder...although Bosch recommend`s replacing the control and I don`t pretend to speak on their behalf nor do I profess to know better. This is just my experience (it work`s) and my opinion (why buy new if one can repair ?)**

**Please disconnect the power before attempting any service to the dishwasher**

Installing a new control will certainly remedy the problem as well but since it is typically around $170 and up just for the part, I am more likely to offer someone an alternative to buying new, hence my first reaction to mention this repair tidbit.

The control is available at most brick & mortar appliance parts stores or on-line at vendors such as "repairclinic.com", "apwagner.com", "searspartsdirect.com" etc. part number is based on your specific model number so you`ll need to provide that.

Hope this answer`s your question's, let me know if I can assist you further. Thank`s for visiting "fixya" for your repair inquiries.

Please take a moment and rate this solution to it's helpfulness to you and leave a testimony if you're satisfied.

Good luck.

macmarkus :)
Repair Help & Product Troubleshooting for Bosch 24 in. SHX33A02 / SHX33A06 Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Bosh dishwasher now runs well past the 105 minutes as stated in the manual, over three hours before I intervene. It gets stuck on the wash mode, it wont drain or rinse, just runs and runs in the wash mode (I know it's in the wash mode because when I open it up, theres suds inside). It will do the wash mode until I reset the wash mode to "Rinse & Hold". I appreciate whatever information you could provide.


Hello, welcome to Fixya.\015\012\015\012The problem you're describing is unfortunately a common one with B/S/H/ built dishwasher's. That includes Bosch, Thermador, Siemens, and Gaggenau. ... Bosch 24 in. SHX33A02 / SHX33A06 Free-standing Dishwasher

The cycle doesn't seem to stop correctly. I start a load. It doesn't seem to matter which mode that I start in, but it will count-down the time, but at the end it hasn't stopped running. I've cleaned out the filter and the trap below. I've ran vinegar through a cycle. I've cleaned all of the spray arms. It doesn't seem to advance out of the wash mode. There is still some suds at the end. I have to end the cycle by canceling and draining it manually, then run a couple of "rinse--9 minute" cycles


Hello,\015\012\015\012Based on your description I'd say the issue is with the control. That is what I'd be looking for if called out to service the unit with the symptoms you've described. \015\012\015\012The issue is within t ... Bosch 24 in. SHU43 Built-in Dishwasher

Frigidaire dishwasher won't end cycle - will run on and on for hours. Sometimes it cycles through, usually it just endlessly washes and rinses. I have to CANCEL the cycle, which causes the dishwasher to empty and run a few RINSE ONLY cycles (which are consistent, cycle time wise) to rinse the soap off of the dishes. Also, the door for the soap seems to stick - how long into the cycle before the soap door should open? Also, does opening the washer during it's cycle (to add more dishes) change or


I would say the resettable thermostat has failed. There is a thermostat which senses the water temperature, and when it fails, it causes the dishwasher to run constant. Replace the thermostat underneath the dishwasher and that should cure problem. P ... Frigidaire 24 in. FDBB540 Built-in Dishwasher

My Omega Eurolux Dishwasher (mode: DW211P/1) won't stop cycling, It sems to get stuck during the wash cycle and continues for hours, until I turn it off. If I turn the dial to rinse it rinses fine. It doesn't seem to heat the water at all, there is no steam when I open the door. I have put a new heating element in, but this doesn't seem to be heating up at all. When I open the door mid wash cycle the element is cold to touch.


... Dishwashers

Hobart lx18 no power to detergent pump, during the wash cycle there is no power present at the connections for the pump, during the rinse cycle the sanitizer terminal will pulse power and the rinse aid and sanitizer pumps will run, is the relay board bad? With the top drawer open and running the led for detergent never lights up during the wash cycle.


You have to go into program and activate the detergent pump.sounds like somebody deativated the det. program ... Hobart 24 in. LXIC-5 Built-in Dishwasher

Have Whirlpool dishwasher Gold Series, Model GU9805CGB1 which stops part way through wash cycle with the led indicator blinks on the normal cycle.....if we ope nthe door and shut ...it continues until part way through rinse cycle...stops again....led indicator blinks again.....we open the door & shut and it continues....but then continues to run through the normal wash cycle continuously.....until we open the door again.....what's wrong???


Sounds like the door is losing contact with the door switch, first thing i would check is the door strike.Metal strike plate located on the tub itself that the door latch catches as it closes. its a spring metal striker, i would try bending it down ... Dishwashers

When I started it, it made a loud grinding sound which continued whenever it was actually washing/rinsing. It was washing and rinsing the dishes ok. Eventually I didn't hear anymore grinding but the dishes had not been washed or rinsed. The detergent cup was open and the detergent spilled down the door. I ran it again and could hear the pump running. It ran through the cycles but the water was not being circulated. I suspect that something is caught in the disposer blade or something and is bloc


What is the brand and model number. it likely will have to be disassembled to clean it out. is it a built in dishwasher or a stand alone type ? ... Dishwashers

I have a ADG 450 dishwasher, it has suddenlt topped completing the wash cycle. it runs for about an hour then sits and beeps. If i open the door, the machine is full of water and it looks as though it is trying to spray more water in, thn stops and beeps. If i turn it off and on at this stage and run the rinse cycle, the water clears and the dishes appear to have been cleaned. any thoughts? it happens with all wash cycles.


... Whirlpool Dishwashers

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

Our Whirlpool dishwasher is two years old and using the same dishwasher and glass cleaning fluid since we installed the unit we are now getting soapy suds in the washer when we open the door. The installer told us to put cooking fluid in several times and run the machine on "rinse". We did this several time and we are still getting suds. Frank Hill 508-879-7425


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. First of all please check the\015\012Water temperature by using a thermometer inside the dishwasher to measure ... Whirlpool Dishwashers

I have a Kenmore diswasher model 587 1525. I can hear the water filling and rinsing, but during the wash cycle I do not hear the motor. At the end of the wash cycle and when I open the door I see the detergent tablet is sitting on the floor. The dishes are not cleaned. Does this mean that the motor has failed or is it the control card. I can hear some clicking noise while the motor should be running. Maybe solenoids cycling.


... Kenmore 24 in. 15252 / 15254 / 15259 Built-in Dishwasher

I have a Bosch dishwasher Model number SHU4302UC. The dishwasher takes about four hours to wash dishes. During the rinse cyle it can be running for over an hour and I will open it to look in side and find that the bottom is full of soap sudds. I believe it is taking too long to wash even though it does a good job.


Possibilities are that of an inefficient heating element ie..scaled up if hard water area especially. whilst the cycle is being completed then the components are working... so other than the element check the drainage for blockages (slow draining add ... Bosch Dishwashers

My whirlpool quiet partner II is not quiet at all. When I start the cycle it starts humming and a little vibrating and I open it up and no water. I close it and wait it out every 10 minutes I open it back up and no water. The heating element is hot and stinky since there's no water. But once the wash cycle is over the rinse cycle works and theres water. What's the issue?


... Whirlpool GU2400XTP Built-in Dishwasher

Hi I have a problem with my Bosch SHU43CO6UC/22 dishwasher. using "power scrub plus" and "regular" cycles it will continue to fill and overflow the door, after the cycle has run even when the power button is off. I am using the quick wash cycle at the moment .After the cycle has run i open and check if the water has drained or not,If it has it does not continue to fill and flood.If there is water in the bottom after the cycle has finished it will keep rising untill I push the rinse hold button


The bosch dishwashers use a fill valve that is attatched to the inlet hose. yours is stuck in the open position. this usually happens when you have hard water, as the minerals build up on the sealing surface of the water valve. there is no easy ... Dishwashers

Asko 1605 cycle stopped, pump keeps running, water pumps out but will not progress to the rinse and wash cycles. Timmer will turn and detergen dispenser will open. Pump keeps running


Thanks my Asko did the same and tilted it forward, drained excess on the floor, even though I thought i'd bailed the whole lot and woolaa fixed - thanks x ... Dishwashers

I have a GU1500XTLB1, type-575-0 Whirlpool Gold dishwasher. For the last couple of weeks I've been getting the control lock on. I got the manual out, I hold the air dry button and it clears. My problem is now when I turn the machine on dosen't matter which cycle I hit (pots and pans, normal, or quick wash) it runs for about 5 minutes and it goes into a mode with the timer having lines going horizontal with the air dry button lit up and rinse button lit up. It sounds like it starts the cycle


Hi,There are Few Tricks to Reset this. Follow the below Tricks :-1. Try holding down heated dry key for 5 secs. I believe that is the control lock/unlock button on your model. IF not, look for the lock symbol and follow same i ... Whirlpool Dishwashers

My dishwasher will not stop running. The timer gets to one minute and will not stop. When i open the door the water is full of suds. When i close the door the timer resets to 13 minutes and continues to wash.


Hi, this is timer failure. simply replacing the timer module(control) will fix this issue. ... Bosch SHU5307UC Built-in Dishwasher

Washer starts with rinse and then nothing else happens. Open the door and find about an inch of water that didn't drain. If I put it in drain mode it drains. Washer won't run full cycle.


... Jenn-Air 24 in. JDB2150AWP Built-in Dishwasher

I have a Whirlpool ADG937 dishwasher (9 years old) which will not complete a 65c wash cycle. It starts Ok and runs for a long time but then continually bleeps, when I open the door the programme indicator light is on the rinse cycle. If I reset the programme to 65c it may do the same or occasionally it will finish the cycle. I have tried salt top-up, descaling and filter cleaning all to no avail. Is the programmer faulty (can I bypass it?)or should I replace the washer?


... Whirlpool Dishwashers

Noisy dishwasher My dishwasher is about 2 years old and about 98% of the time it makes a very loud growl/rumbling noise in the wash and rinse cycles. I have checked to make sure that it is not clogged and open the door during the cycle but can't pinpoint where the noise is coming from. Sometimes it runs with no noise but that is not usually the case. Any thoughts?


This is a known issue for GE dishwashers and may be similar for other\015\012models too.  The fix is simple.  The noise is due to\015\012vibration of the arm for the middle sprayer.  Just secure it with\015\012a tie wrap or wire and th ... Dishwashers

Noisey maytag We have a maytag quiet series 300 with the 3 racks. Just recently we have been hearing alot of noise from our dishwasher while it is in the washing and rinsing mode. We have checked the arms to make sure they are moving but doesn't seem to be a problem. Thought maybe there is a liquid that we could pour into the washer to run through it's cycle? Of course we know nothing about the inter works of a dishwasher.


Hi, i had the same problem twice and both time there was some plastic stuff in the shredder. Remove the screw in the middle and remove the cap and you will probably find some pieces near the blades. ... Maytag 24 in. MDB5651A Built-in Dishwasher

Help! My dishwasher runs thru it's cycles but when I open it I find my second detergent cup still full of soap and my dishes still dirty. I have an older maytag dishwasher but have never had this problem with it. I've tried running a short prewash cycle with the soap despenser open to wash out the soap from the open second despenser but it doesn't wash it out. I know water is coming out of the spray arms but can't see if the arms are spinning although when running it does sound like they ar


Hi,\012There are three common problems that cause the Soap Dispenser or Cup not to open. I have a tip that will explain these problems in detail....Dishwasher Repair Problem ... Dishwashers

During wash cycle it gets stuck and won't move past the wash cycle. On a regular wash it is at 28minutes and when it is on a fast wash it is at 25 minutes. If I stop it and turn on the rinse cycle it will run through the 12minute rinse cycle with no problems. It is only the top dishwasher that does this, the bottom one is running just fine.


I've got the same problem with the bottom drawer on the DD605. No fault codes were set. I checked the heating element and it produced heat quickly. I suspect that the water temp sensor isn't satisfied, and the timer is waiting for the water to rea ... Fisher and Paykel DD605BK Dishwasher

Dishwasher runs for appx 14 min & stops washing half way thru wash cycle. Timer contunies to run. No drain pump out (nothing). Let dishwasher set idle for appx 1 hour and it will re-set. Set timer forward to end of wash cycle and it will complete rinse and final rinse. Then go to dry. Timer works ok.


This sounds like something is stuck in the drain pump. You can remove the inner cover to look for obstructions. You have a dual purpose motor it does the both circulating and draining. The blockage is causing it to overheat and trip the thermal prote ... Whirlpool DU840CWD Dishwasher

Maytag model mdbtt70aww. After the end cycle. open the door and found detergent tab on the bottom and the main wash cover is opened. Maytag diswasher model MDBTT70AWW. Put dishes and so forth in the dishwasher. Put detergent tab and jet-dry rinse agent in the pre-wash section. and close the cover. Start wash cycle after done over door and found the detergent tab on the bottom new the heater. The cover to the main wash is opened. Dishes are are clean. Wish someone would tell me


... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1594 seconds