Having problems with your Bosch 24 in. SHX33A02 / SHX33A06 Free-standing Dishwasher ?

Bosch SHX33A: lights come on properly in response to buttons, it has power. Close door, it makes the normal startup sounds, then water flows in. Normally, at this point washer starts into normal cycle. Instead, it just sits there and nothing happens. Forever. Not a matter of patience: we've left it in that state all night long. Have flipped power circuit and started over, everything else I can think of to kick-start it, no change.


Answers :

Hi
\015\012\015\012

The issue seems to be with the motor or the door latch\015\012assembly going bad and should be replaced. The washer won't start the cycle if\015\012motor is not working, as its filling with water so I believe that the door is\015\012fine and it is the motor that is causing this issue. Hope this helps...please\015\012post back for further assistance.
\015\012\015\012

Daniel

Repair Help & Product Troubleshooting for Bosch 24 in. SHX33A02 / SHX33A06 Free-standing Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bosch SHX33A: lights come on properly in response to buttons, it has power. Close door, it makes the normal startup sounds, then water flows in. Normally, at this point washer starts into normal cycle. Instead, it just sits there and nothing happens. Forever. Not a matter of patience: we've left it in that state all night long. Have flipped power circuit and started over, everything else I can think of to kick-start it, no change.


Hi\015\012\015\012The issue seems to be with the motor or the door latch\015\012assembly going bad and should be replaced. The washer won't start the cycle if\015\012motor is not working, as its filling with water so I believe that the do ... Bosch 24 in. SHX33A02 / SHX33A06 Free-standing Dishwasher

Lights on Dishwasher light up but nothing happens. When I reset power it lights up the high temp and sanitize button light up and LED displays PF. After I open the door they stop flashing. the far left five buttons light up when I push them and a corresponding number displays on the LED screen. the only lights that do not come on are the Delay button and power button. Don't know if they are working or just don't light up. No matter what lights up the unit does not turn on....:( ? help can't fin


Pf is power failure\015\012 your loosing voltage to the unit \015\012it may just be the door switch or it could be in the control\015\012 try starting the unit but keep your hand on the unit pushing the door in place,, its not a g ... Electrolux 24 in. EDW5500DSS Stainless Steel Built-in Dishwasher

After dishwasher was started, and water stared to enter the machine, it was unlatched and left with the lever in the open position for some time. The control dial had automatically moved 5/6 degrees clockwise and left there. Now the machine does not want to start no matter what I do. Power is to the machine, latch is moved to the right, but nothing happens. What's next. Thanks for any help you can give.


Hi,\015\012 \015\012After the water stops coming in do you hear a humming noise? If so the motor may be stuck. Unlock the door to disconnect power from motor then turn the motor by hand a few times (should ... Dishwashers

Frigidaire Dishwasher Hi, I have installed a new model GLD2250RDC0 Frigidaire dishwasher and it will not start. Power and water supply is connected. When I push the cycle button for Normal the light comes on but when I push Start nothing happens except the "hi-temp wash" and "no heat dry" lights flash. I assume this is some kind of troubleshooting code but the manual does not cover this and I am in Honduras so service is non existent. Any ideas? By the way, I was a builder in the States for 25 y


... Frigidaire 24 in. GLD2162RDC Stainless Steel Built-in Dishwasher

My Ge profile Triton Dishwasher wont start when I lock it just keeps beeping and the" normal "light flashes there was something stuck in the turnstile and it stopped and beeped all night when I took it out it was left this way I have turned the power off and on and I still cant reset it any ideas it just wont reset


... GE Dishwashers

Opened door and unit did not have electrical power (lights did not come on either unit). Called serviceman. He stated there was no electricity to unit(s). Called electrican. He stated wiring to the dishwasher had power. Called serviceman again. He came out and dishwasher worked. He did nothing to it. I opened the door and the lights(buttons) came on. Unit worked for a few days and this morning, there was again, no power to the unit. What is likely wrong with this dishwasher?


... Fisher DD603B / DD603W / DD603H Dishwasher

Have the Fisher & Paykel single drawer dishwasher ds 603 and put it on a normal cycle last night. It started as per normal and sometime during its cycle it stopped and the drawer now seems locked. The power doesn't work at all now and tried turning it off at the power point - still no response.


It is very likely the thermal fuse has blown or the power supply board has had it. Either way the power to the controller and the drawer lid seal motors is cut off. This is why the drawer is in locked state as the motors have seized.\015\012 ... Fisher and Paykel 24 in. DS-603 Built-in Dishwasher

I have a candy futura cdf322-80 dishwasher,done a load as normal then i put it on the next day and there was nothing no lights came on nothing, i checked the fuses and the socket they were fine,so i had an engineer out who said there was power going to the machine so he said it was the contol panel which is situated behind the temperature and programme buttons so i bought this part and replaced it but still there is nothing.


I would check for myself if there was power going to the machine. If it acts the ways your does, then either the control panel or the power supply is at fault. Slight possibility a wire that runs between the two may be faulty, but not as common ... Dishwashers

I have a Magtag dishwasher, model #MDB6650AWQ thats not running. I check the power supply all the way up to the door latch and it shows that there's power there. However the circuit panel not lighting up and nothing happens when you push the normal wash cycle or any of the other buttons. I believe the problems is electrical in the door latch handle. Is there any way to check the solenoids which are attached to the door handle before I order a new door latch.


I have the same problem with mine. It is 3 1/2 years old. The repair man was just here and said it is the control panel. It will cost $171.85 for the part and then $53.85 today for his visit and then a return visit when the part is in.\015\0 ... Maytag Dishwashers

I HAVE POWER TO MY GE DISHWASHER BUT IT DOES NOTHING. NORMALLY WHEN I REPRESS THE PLUNGER SWITCH IT BEAPS AND LIGHTS UP. NOW IT DOES NOTHING.


Hi\015\012\015\012Thanks for using FixYa. Usually this happens when the control board has gone bad or due to loose/burnt connections on the control board. Please tell me how many beeps do you hear and also the status of the lights. Also t ... General Electric GHDA485NCS Built-in Dishwasher

Our dishwasher model is a Nautilus FP920WW. The unit switches on OK and displays the normal wash cycle settings but when we try to start or change a cycle (or press any button for that matter) all we get is a quick, intermittent beeping and nothing happens/changes. Switching the dishwasher off and on again at the wall does nothing to solve this problem. What's going on???


... Fisher and Paykel Dishwashers

My KitchenAid dishwasher model # kudp01ilbl2 won't start. It is the first time we're trying to start it since we had our water heater replaced (three, maybe four days ago). Not sure how much that may matter. I tried turning off electricity to the dishwasher at the fusebox (overnight), but that did nothing. Normally, you just need to hit the start button and the washing begins. Now, nothing happens. The dishwasher is about six years old.


... KitchenAid Dishwashers

I have a Whirlpool Quiet Partner II. The normal light is blinking. If I press start it does nothing. If I press cancel, the cancel light blinks too. We turned off the power and let It sit for a few minutes. Powered it back on and same thing.


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Dishwasher lights up when Normal Wash is pushed, also heat dry - but when start is pushed all three lights (Normal wash, heat dry and washing) blink then go out and nothing happens. This occurred after a 2 hour delay was attempted last night and no washing ever happened.


What is the make and model so we can better assist you? In the mean time shut power off to the unit briefly, then turn it back on and try a normal cycle. Will be watching for a make and model here. ... Dishwashers

I have a KitchenAid KUDS02SR dishwasher. If I push any buttons on the control panel the Normal light starts flashing rapidly and will not stop no matter what I do. While this is happening it will not start a cycle. If I turn off the power the light will stop flashing, but when I push any other button the Normal light starts flashing again.


The touch panel may have a bad push pad and will not let it probram there is a tech sheet under the dw just behind the toe panel this wil help you understand the flashing code . it will tell you what is wrong . but a ... KitchenAid 24 in. KUDS02SR Built-in Dishwasher

Hi I have a beko DE3542F dishwasher and the last time it went it just kept taking water. i switched it of and drained of the water, now it just does nothing and appears to be in the middle of a cycle. I left it on for some time but nothing happens. The light are on for power and wash.


Hi\015\012\015\012The issue is with bad timer motor/control and should be\015\012replaced. The water fills fine and drains fine which indicates that everything\015\012is fine and even the motor is working so the Timer should be replaced t ... Dishwashers

Used some washing up liquid instead of dishwasher tablets, after i got rid of all the bubbles and drained it, it no longer starts. If i switch the power off and leave it for a few minutes i can select a prgram it starts and a few seconds later there is a beep and the solid green run light on the program selectoe is flashing over the left hand program button. At this stage pushing any program button does nothing, i have to swith the power off and wait 5 miniutes and the the above patten is repeat


Dear sir vif you have used liquid soap in your dishwasher it will make mountains of bubles to kill all bubles outin a hurry take a sos pad put it in your machine and run the dishwaser this will remove all of the soao instantly try it it really works ... Ariston Technologies Dishwashers

Hello My Haier DWI 5212P (also known as Proline DWI 5212P) dishwasher is not working. The indicator panel has 3 nights flashing so I realise these are warnings, but do not know what they are telling me. In order from left to right the 1st, 2nd and 4th LED's are flashing. Those are the ones that I would normally press for Heavy Duty, Normal Wash and Glassware. Any advice you can offer? Thanks in advance. Cheers Davie


... Dishwashers

I have a KUDSO2FRWHO- this was the closest I could find to it. I think we had a power surge at the house- now my Normal button flashes constantly. If I push cancel, then the normal and cancel bottons flash together. I have tried unplugging it and replugging, nothing seems to help- what should I do?


Unfortunately the control board is faulty. you will need to open the top section of the door to gain access to the board. With door open, you will see 6 screws that need to be removed to pull top section away, There you will see the board. Take th ... KitchenAid 24 in. KUDS02FRSS Stainless Steel Built-in Dishwasher

No matter which cycle selection in pushed, the dishwasher only starts up in the "normal" 93 min cycle. If I try other cycle options, and persist, I get an ER message and the cycle stops prior to the soap powder door opening and never completes the cycle. Only with turning off power for several minutes and receiving the PF message, and resetting ONE TIME that message can I then select any cycle, at which time the machine "defaults" to the "normal" full cycle. If I do not disturb that cycle, it wi


Looks like you are having a good deal of problems with the dishwasher.\015\012\015\012It will be helpful if you provide the make and model no. of the dishwasher.\015\012\015\012At this stage I can speculate the controller (ass ... Dishwashers

Normal light is flahing unit will not go on sometimes time remaining indicator will flash started awhile back by not being able to change any settings but unit would work now nothing have tried disconnecting power still nothing


HiIf clean light is blinking 7 times then it may be an issue with heater circuit, door switch or wash pump. If yes then please reset the power to the dishwasher. After, 5 minutes check if you are still getting the same ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Gsd5500 ge dishwasher normal light flashes when locked and nothing happens. also the soap container will not lock closed, it just returns to its open state


... GE 24 in. GSD5500G - Multiple Color Built-in Dishwasher

Will not push any water thru was working night b4 but when turn on makes a clicking sound tries to run thru process but nothing happens still releasess soap power???


Is possible that some object is jam on the pump water inlet. ... Dishwashers

Dishwasher does not seem to have power. I have a Kitchen Aid, under counter unit, 9 years old, model KUDS01I. I used it 2 nights ago with no problem. When I push a button, nothing happens, no lights show, etc. It is plugged into the lower half of a duplex socket with disposal plugged into the top. Disposal works, so the problem seems to be with the dishwasher. That also eliminates any issues related to breakers or ground fault indicators, etc. Is there a reset button on the dishwasher? Is there


... KitchenAid Dishwashers

I loaded my dishwasher lastnight as normal closed it and hit the start button and nothing happend. its like it has no power! what can i try before calling someone?


First check electrical supply,second check switch continuity,3rd check door switch or reed switch if contact properly. ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1195 seconds