Having problems with your Bosch 24 in. SHX46A02 / SHX46A06 Built-in Dishwasher ?

We have a Bosch dishwasher SHX46A06 UC/21. It continually runs. We couldn't find a diagnostic test for our model, but we did for another model. We held down the power scrub and regular wash cycles then turned it on and pressed them again. The delicate/econo light started blinking. Looking at some of the blogs, most often it seems to be the heater or the control panel - does this diagnostic test help to pinpoint what could be wrong? Also, where can we find a good manual for our model - we're havi


Answers :

Here is a link to the service manual http://cgi.ebay.com/Bosch-Dishwasher-Service-Repair-Manual-/250480379703.
\015\012
\015\012Generally, when this happens, the control board is not turning on the water heater due to a bad control board, heater or limiting fuse.
\015\012
\015\012Joe
Repair Help & Product Troubleshooting for Bosch 24 in. SHX46A02 / SHX46A06 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We have a Bosch dishwasher SHX46A06 UC/21. It continually runs. We couldn't find a diagnostic test for our model, but we did for another model. We held down the power scrub and regular wash cycles then turned it on and pressed them again. The delicate/econo light started blinking. Looking at some of the blogs, most often it seems to be the heater or the control panel - does this diagnostic test help to pinpoint what could be wrong? Also, where can we find a good manual for our model - we're havi


Here is a link to the service manual http://cgi.ebay.com/Bosch-Dishwasher-Service-Repair-Manual-/250480379703. \015\012 ... Bosch 24 in. SHX46A02 / SHX46A06 Built-in Dishwasher

SEARS/WHIRLPOOL DISHWASHER Model 665.16014401. The CLEAN light keeps blinking and washer will not run. Op. instructions say to check the heater circuit. Heater element tests at 12.9 Ohms and thermo unit at 55 K ohm and the unit I beleave looks like overtemp cut out is less than 1 ohm. these look like good #s to me so I suspect the controller p/n 8564544. When I look up the number online I find it has been replaced with 8564546, but the only picture I can find of it looks like the connections are


... Kenmore Dishwashers

Whirlpool Gold Quiet Partner IV Dishwasher, Model GU1500XTKT0, Serial number FL4104935, Type 575-0, during a Rinse Only cycle suddenly the cycle light began constantly blinking, which could not canceled or stopped nor placed into diagnostic cycle or other wash cycle. The repairman checked everything and decided problem was Electronic Control Module, which he replaced; blinking Rinse Only went off, but Normal Wash is now constantly blinking and repairman seemed confused and is wanting to repla


... Whirlpool Dishwashers

Customer bought house with a Viking Dishwasher already there. He has no user manuals or documentation with the model number listed. None of the stickers on the side of the door have a Viking model number. This unit is a Quiet Clean System with Auto Water Heating and is (he thinks) about two years old. How can I find out what the model # might be or better yet how do I find out the part # to fix the main control board / interface. It just keeps blinking.


Check the back of the unit for a tag.... otherwise - removing the clock... it should have a part number on it.\015\012\015\012Thanks! ... Dishwashers

I HAVE A MAYTAG MODEL MDBTT59AWQ DISHWASHER THAT WILL NOT START UP. LIGHT ON CONTROL PANAL FOR HEAVY AND LIGHT LOAD LIGHTS, DELAY ONE DOESNT AND THE START/CANCEL ONE DOESN'T LIGHT EITHER. WORKED FINE A COUPLE DAYS AGO. TRYING TO FIND A MANUAL OR PARTS BREAK DOWN BUT CANT SEEM TO FIND ONE FOR THAT MODEL.


... Maytag Dishwasher

FDW60 Fault Hi, I have exactly the same problem. My dishwasher starts and washes ok but appears to get very hot during the drying phase and then the two lights fast and eco flash warning of a heater problem. I suspect either the heater, thermostat or control PCB. As the rest of the cycle seems of and the water gets hot then I'm assuming the heater and thermostat are OK. When the dishwasher attempts to dry is when the problem starts. Did anyone find out what there fault was? Thanks


Hold down the start key and you will re- set the D/W. Please Rate This !!! Thank YOU !!! ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

I have a Kitchenaid Dishwasher Model #KUDI01FLBL6. The heavy wash light is blinking on it. If I hit cancel, all the lights start blinking on the panel. I have replaced the control panel part #8564542 on it and it's still doing the same thing. The tech sheet is missing on it so I'm not sure if I should reset or how to do a diagnostic on it. Can you help with telling me what to do?


HI. The control board was actually not the issue here. The interface will be the lone culprit in this case. There is a stuck circuit or button that is causing this warning(blinking lights). The button is mounted on the interface and you will need to, ... KitchenAid 24 in. KUDI01FL - Multiple Color Built-in Dishwasher

I have this model dishwasher and last year I spent close to $300.00 having this control panel replaced and as soon as the warranty went p it stopped working again, but there is a green light that blinks next to right side where it says clean. It seems like it is blinking in sequence.. I cannot afford to spend this kind of money to have this fixed again. The co. that has the contract with kitchenaid is horrible and do not double check their work. The only thing tey care about is the bck.


Sorry to hear about the trouble with service. I have put together a sheet to show why the clean light blinks and how to reset the control so you can use it. Let me know if you have questions I would be happy to assist. Here is the link to the instruc ... KitchenAid 24 in. KUDP01IL - Multiple Color Built-In Dishwasher

I have a kenmore dishwasher model #655.1374 or 655.1384 which is only about a year old. I am having a problem with the controls. It will not allow me to use smartwash. The only control that can be used is quick rinse. I reset it by pushing Sani rinse and heated dry. All the lights come on and it seems to do a test. But after that still the same thing except if I push start resume it goes to normal wash which stays on a long time and periodically the cancel drain light comes on as well as the 4


... Dishwashers

I have a MDB5130AWW model dishwasher and it has worked extremely well up until a week ago. Now there is water sitting at the bottom of the dishwasher, and the "Clean" and "Rinse Only" buttons are blinking. I've read the manual, and ran the Automatic Function test, and it seems that these two buttons blinking indicates a Motor problem, specifically a low current problem. Please Help!


You may have a seized/stuck motor. Turn the electricity off and remove the lower panels. Take a flat head screw driver and carefully attempt to move the motor impellers. If the impellers feel hard to turn continue to try and free the impellers. I ... Maytag Dishwashers

The control panel on my Frigidaire Professional Series 24 is not working. The lights are all blinking and the letters Er s are flashing. The model number is FPHD2481KF1. I cannot find what these three letters mean exactly! Thanks.....


... Electrolux Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

My Frigidaire dishwasher, model #FD949GFT2 (12 years old) has a blinking "CL" on the control panel and will not operate. The door latch "seems" to be engaging properly, any suggestions?


Hi,You are absolutely Correct. It sounds to me like the latch switch is not registering that the door is closed.However, as PF is also there, i am doubt, it could be Faulty Pad or Control Board. Most of the times, i have seen ... Frigidaire Dishwashers

My Kenmore model 665-16919001 control panel stopped lighting up, nothing will come on. I can't seem to find reset codes anywhwere. Can you help?


... Kenmore Dishwashers

Extremely heavy limescale residue on all items after dishwasher has finished. water temp in house has been turned down. Had water tested by city water company and results were clear. 12 months ago maytag replaced heater element under recall, but dishwasher always seems too hot. Neighbours do not have this problem. Any advice would be most welcome.we only use quality powder and rinse aid. Have cleaned dishwasher numerous occasions. model MDB4651AWS1 SERIAL # NW5015848


Hi,The scum, film and white residueproblems have started since the reductionof phosphates in dishwasher detergents.Here is a tip that will help you to solve the problem of films, residue, and scum in your dish ... Maytag 24 in. MDB4651AWS Stainless Steel Built-in Dishwasher

No heat washing cycle completes normaly, exept no hot water or drying.i tested heater for resistance and seems ok,is there a fault with control pcb or is there a faulty sensor that im not aware off? can you make any suggestions? thanks steve


You should check for 115/220v on heater tags,\015\012In case you don't have it, your problem is a malfunction thermostat that should be replaced.\015\012\015\012Good luck! ... Zanussi 24 in. ZSF6120 Free-standing Dishwasher

We are working on a Whirlpool Dishwasher Model # DU915PWSS and need to find the "test sequence" aka "key dance" to run a diagnostic. Does anyone have this information? Thanks


Hi, well all this information is in your manuals, accordingly i include a link for your service manual, below.\015\012\015\012http://appliancejunk. ... Dishwashers

Bosch Dishwasher model SHU66C06 doesn't enter wash cycle


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

My maytag MDBB7100AWQ stops in mid cycle at the same place all the time (for background see robert920 problems) I tested the heater continuity and found no continuity between the heater and the outer skin of the heater and the resistance of the heater was fine. Then I run the diagnostics (Automatic function tests) and its indicated Keypad 2 which is Motor -low current. I then went on to test the resistance for the motor and found out that they were all within specs (Blue to Gray 7 ohms, Bl


\015\012Ok so your dishwasher won't do anything... it justs sits there and "Hums" you can't make it respond to any controls, and the ONLY way to Stop it. is to unplug the unit, replugging back in it simply "Hums" again and will do nothing. ... Maytag MDB7100AWB Dishwasher

I have a Whirlpool Gold Quietwash Plus (part # 9744480), due to a number of opening and closings of the door, the lights on the front panel now just blink. How can I reset the control panel.. I have tried power scour>air dry>power scour>air dry and only end up with both blinking instead of going into control diagnostics by pushing pots&pans. The unit will attempt to start then just go to blinking lights.. Thanks


I would cut the power to it for awile 5mi and try it that may do it ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

I purchased my Kenmore Elite dishwasher, model # 8542514, in 2003 & replaced the control board in 2006. Recently, I accidently opened the dishwasher during a wash cycle, but it continued working once I closed it. It seemed to work fine for a few more weeks. Now, however, I get nothing--no lights....just doesn't start up. I tried pressing all the code solutions listed on this site, but no luck so far. It seems to me that the control board/panel should last more than 3-4 years.


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Kitchen Aid Dishwasher model # KUDK03CTSS3 The control panel lights are blinking rapidly, several of them. Nothing works, even after powering off and on again. I see there are instructions to reset the control panel on these before calling for service. How do I reset the panel on this model?


... Dishwashers

I have a Kenmore Elite Dishwasher Model 665.13773K600. It seems to have no power to the touch pad (top) control panel. I have already checked the circuit breaker and the power to the dishwasher. A friend said that it may perhaps be the thermo fuse cut out that needs to be replaced. 1) Is this true? 2) How can I remove the 1" thick control panel touch pad after removing the six screws- it seems to be stuck, and I don't want to break the plastic touchpad.


... Kenmore Dishwashers

My Asko 1473 Superior dishwasher has just stopped filling. I've gone through the on-board diagnostics and find that the fill solenoid operation does not work. All other diagnostic tests are OK. I have no service manual but would like to find and replace the solenoid if that is all that's wrong. Can you help with advice or manual? cheers, Hal


Asko ... Asko 24 in. D3250 Built-in Dishwasher

Kitchenaid Superba (model # KUDS01FLBL6). The light by the control lock/sanitized/clean on the control panel keeps blinking. I called Kitchenaid and they recommended turning off the circuit breaker. I did this for 5 minutes and the light is still blinking. Washer won't run. Help!! Family is in for Christmas and I can't wash everything by hand...I'll never leave the kitchen!


... Dishwashers

How do you run the diagnostic on a bosch dishwasher model # SHE44C06Uc/22. it counts down to one on the timer and runs forever. can't find it model # diagnostics anywhere. thanks


Resoldering the relay, regardless of how proficient one is at soldering, will not be a long term solution. The melted/burned solder joint is a secondary result of the initial failure, which is the relay itself. There is a solution that is more perman ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1515 seconds