Having problems with your Bosch 24 in. SHX46A02 / SHX46A06 Built-in Dishwasher ?

SHX46A02UC dishwasher will not complete cycle. Just installed new circuit board. Will also run with door open. Seems to be stuck in drain mode.


Answers :

Test the door switch and its wiring. The dishwasher is supposed to stop when door is open.

About drain pump, check the pressure switch and eventually replace it(pressure is water level, this is not the float, that is usually overfill-if there is no pressure switch, check float). That is the device that detects if drain is over, stopping the drain pump.
Repair Help & Product Troubleshooting for Bosch 24 in. SHX46A02 / SHX46A06 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

SHX46A02UC dishwasher will not complete cycle. Just installed new circuit board. Will also run with door open. Seems to be stuck in drain mode.


Test the door switch and its wiring. The dishwasher is supposed to stop when door is open.About drain pump, check the pressure switch and eventually replace it(pressure is water level, this is not the float, that is usually overfill-if th ... Bosch 24 in. SHX46A02 / SHX46A06 Built-in Dishwasher

I have a bosch dishwasher SHE43C06UC22 (non-LED version). It's stuck in the drain cycle and continues to run even when opening the door (it should stop, but it doesn't). As a test, I poured a large glass of water in the bottom of the dishwasher and it drained it into the sink as it should, but it continues to run in the drain mode with no water in it. I've heard I either have a float stuck or an emergency drain switch or leak somewhere causing the dishwasher to continue in the drain mode. Ho


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012This can be caused by either faulty door switch or indeed the float you mentioned.\015\012\015\012This is where to look for the switch and test it ... Dishwashers

Asko 1585 Dishwasher. Lately the washer has not been completing it's cycle without going into the all lights flashing mode. Usually just opening the door, closing then pushing start gets it going again. Yesterday this happened and it was restarted as described, then it go stuck in what appeared to be a drain mode - all lights flashing, drain motor running. It was in this mode for several hours and could not be stopped by any means. Pushing buttons or opening the door had no effect. Even c


Hi\015\012\015\012\015\012\015\012Thanks for using FixYa. You are right it is related to a bad control board. The\015\012control board has gone faulty and needs a replacement. Please check this recall\015\012information--- ... Asko 24 in. 1585 Built-in Dishwasher

Bosch SHU4302 WITH REPAIRED PC BOARD has been working fine for several years now seems stuck in rinse/drain mode and is not quite pumping cabinet dry. I have removed the screens and located the small impeller at bottom below cover. The impeller rotates as though it has multiple spring loaded stop positions. When I turn on the unit and open the door water is trickling from the sprayer arms at low pressure. It seems stuck in rinse mode and will not advance cycles or reset when shut off.


... Bosch Dishwashers

After cycle completed, opened door and found water did not drain. i removed the screen at the bottom and used wetvac to **** all the water out. i was also able to hear suction from hose to sink P trap. i'm confident there is no blockage. i attempted to run again only to find out the pump was running but, no water was filling the machine. Yes! the valves are open! two different issues? one other thing; due to the no thought behind this, the name plate was stuck to the inner part of the door whi


Possible that the drain pump needs a closer look , clean and check if the pump is working. If there is voltage to the pump during the drian then the pump is faulty.\012The second issue if the inlet chocking , check the inlet filter , check the ... Bosch SHU9915UC Dishwasher

Control panel buttons don't work. Seem to be stuck in the "Lock On" mode. Can't turn off, and dishwasher won't run. When you open the door all lights go off, but as soon as you relatch the door, the "Lock On" light comes on, although sometimes it can be another light. In any case, it won't run.


... Kenmore Dishwashers

My GE Nautilus DW doesn't fully drain. When it is drained as much as it will it leaves water in the sump at the rear right. If you run the pump at that point, it sucks water out of the sump, but when you open the door and the pump stops water flows back into it. It seems like there is a check valve that isn't working. I have cleaned the sump and the screen which runs accross the rear. I also have taken the plunger out and cleaned it. Then I took the housing for the plugner off the bottom. I don'


HI. check the following areas for fualts.1. Air gap / Drain hosesIf there is an air gap (located in the sink, near the faucet), check to see if it is clogged. Unscrew the top cap and see if there is anything blocking inside. Note: I ... Dishwashers

Hi. I have a Siemens SE65E331GB Built in Dishwasher with an aquastop system. The problem is that it seems to be stuck at the end of a cycle. The pump is constantly running when stitched on. I won't top after a reset and it continues to run even if you open the door. The water supply light also comes on indicating that there is no water getting to the machine. I have tried resetting the aquastop as per the advice in other threads. This has helped in that the water supply light now stays


... Siemens Dishwashers

Good morning, I have a F&P dishdrawer ds605i (i think!) single drawer intergrated front. I dont know whats happened to it. The last cycle it decided not to empty the water out, so i manually emptied it. Now it seems stuck. All it does is run the fan. i can't start a new cycle. The start/pause button allows me to open and close the door as normal and i can hear the lid opening and closing.......... I have tried turning it off for a day at the wall switch. I have also noticed i can


Hi \015\012I guess the model no. you have sent is not correct,however given bellow are links from where you can troubleshoot your problem to your dishwasher which is related to your issue:-\015\012 ... Dishwashers

I have a kitchenaid dishwasher mod KUDK01TKBL1. It was running fine, opened the door and now the unit is dead,no lights nothing. It has 119 volts to it, the circuit board has line voltage and the door switch seems okay. I could not find any thermal fuse in this unit


... KitchenAid Dishwashers

Frigidaire dishwasher won't end cycle - will run on and on for hours. Sometimes it cycles through, usually it just endlessly washes and rinses. I have to CANCEL the cycle, which causes the dishwasher to empty and run a few RINSE ONLY cycles (which are consistent, cycle time wise) to rinse the soap off of the dishes. Also, the door for the soap seems to stick - how long into the cycle before the soap door should open? Also, does opening the washer during it's cycle (to add more dishes) change or


I would say the resettable thermostat has failed. There is a thermostat which senses the water temperature, and when it fails, it causes the dishwasher to run constant. Replace the thermostat underneath the dishwasher and that should cure problem. P ... Frigidaire 24 in. FDBB540 Built-in Dishwasher

Bosch SHX46A (6 years old) Selected regular cycle, pressed On and closed door. Cycle did not start normally. Pump runs, but no water is coming into the DW. I confirmed the water supply line is turned on. I opened door, turned off On/Off switch, then poured water into drain. Then turned On/Off switch on. DW began pumping water OUT of the DW. Also, it doesn't matter if the door is open or closed - if you turn the DW on, the pump will run. I suspect a problem with the electrical controls, or perha


From your description, I doubt that the problem is door latch is the cause.\015\012\015\012The first thing that a modern dishwasher does before it begins to fill with water is run the drain pump.  It appears that this DW is not progressing ... Bosch Integra® 500 SHX46A0 Dishwasher

My Frigidaire Dishwasher FDB1050RES2 gets stuck in a rinse cycle. The light on the front will be lit "clean" but the bottom of the washer is full of water. Opening the door does not turn off the "clean" light. For me to get it to run, I have to unplug it, plug it back in, push the start button until the ?washing? light comes on. I then push the start button once more and the dishwasher will begin to drain. I open the door as soon as I hear the water stop draining into the sink drain. This


By the descrition you are giving you will need to replace the main control board.Part number 154568401.you may also need to check the float switch.The part will run about 110.00 dollars from a local parts store ... Frigidaire 24 in. FDB1050RE Built-in Dishwasher

My Bosh dishwasher now runs well past the 105 minutes as stated in the manual, over three hours before I intervene. It gets stuck on the wash mode, it wont drain or rinse, just runs and runs in the wash mode (I know it's in the wash mode because when I open it up, theres suds inside). It will do the wash mode until I reset the wash mode to "Rinse & Hold". I appreciate whatever information you could provide.


Hello, welcome to Fixya.\015\012\015\012The problem you're describing is unfortunately a common one with B/S/H/ built dishwasher's. That includes Bosch, Thermador, Siemens, and Gaggenau. ... Bosch 24 in. SHX33A02 / SHX33A06 Free-standing Dishwasher

Gets to the end of the cycle (1 minute left on countdown) and just keeps running, does not start the "dry" mode. will run until i open it and when i shut it it goes 13 minutes left on the countdown but then gets stuck at 1 minute again. does not drain. has been doing this awhile, but until now it would simply finish the cycle when i opened, closed and reset it. now it just gets stuck again.


Hello,Welcome to FixYa.Based on your description ... Bosch SHU5315UC Dishwasher

My Omega Eurolux Dishwasher (mode: DW211P/1) won't stop cycling, It sems to get stuck during the wash cycle and continues for hours, until I turn it off. If I turn the dial to rinse it rinses fine. It doesn't seem to heat the water at all, there is no steam when I open the door. I have put a new heating element in, but this doesn't seem to be heating up at all. When I open the door mid wash cycle the element is cold to touch.


... Dishwashers

Gibson Furnace Hi and thanks for reading my question. I have a Gibson furnace with electronic ignition. When I turn on the power to the furnace it starts running with the batteries removed from the thermostat. It blows but does not produce cool or or stop running. The circuit board has a small red light that is flashing but does not seem to have a pattern. I would appreciate any input that you may have. Also are the relays located ont he circuit board itself?


... Dishwashers

Dishwasher starts and runs to 2nd rinse cycle, when pump starts to pump water out, all lights on front display flash along with key pab lights blinking. you can turn off and restart, but is does the same. Diswasher will also try to start when in off mode. Replaced circuit board and it does to same. Did I get a bad circuit board or is there another problem. Also when I try water service test, I get a Rinse aid fault.


U REPLACED THE CIRCUIT BOARD IN THE DOOR, THE ONE BEHIND THE CONTROL BUTTONS? THAT IS THE TIMER, IT IS KNOWN AS THE CCU OR CENTRAL CONTROL UNIT, THAT IS WHAT CONTROLS ALL TIMED FUNCTIONS, SO THAT REALLY IS THE ONLY PART THAT CAN CAUSE THIS PROBLEM ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

GU1500XTLS3 Periodically won't start. Dishwasher has power because pressing cancel causes dishwasher to start draining (even though there is no water). Door switch works because opening door prevents starting drain cycle. No other button on control panel will work except for the 'air dry' / 'lockout' button. Turning off circuit breaker for 15-30 minutes and then turning circuit breaker back on seems to fix the problems but only for a couple uses and then it stops working again. Need ad


This could be the 'fill switch', which is the level sensor. Could be a plastic tube that exerts air pressure into the tube as it fills, make sure it's clear and open. The dishwasher has a sensor that monitors the door being closed too. Some use a hig ... Dishwashers

Hotpoint LFT 114 dishwasher Cycle seems to run OK BUT water cold. No flashing of lights to indicate error, lights appear to behave as normal. Metered the heater element, not open circuit or short circuit. Metered the NTS resistance goes down as temp goes up Dismantled and checked all connections, all seem good. Ran the self test program and it seemed to get stuck in the wash stage, never seemed to move on BUT no error message. Now what, any suggesting please guys??


... Dishwashers

I have a Kenmore dishwasher model # 66513449K900 that will not stop running. I think it is stuck on the drain cycle. I can start the dishwasher on a cycle and it appears to clean the dishes, but after the cycle is complete, it continues running and running (on the drain cycle) until you open the door. What could this be?


It is possible that the machine does not move off the cycle because there are errors or back feedback from the inputs. For the program to end the main program controller must receive the feedback so as to switch off the circuit at the end o ... Dishwashers

Dishwasher - Bosche - SHV43A03GB - When the main power switch is ON, even with the door open the pump/motor continues to run (ie. Stop-cycle does not operate). However, the wash-program itself does not run, even with the door closed (ie. No water entering the dishwasher, even though water supply is on and feed lines are clear - not kinked). It is like the program is 'stuck' and I cannot seem to get it to reset.


Your door switch is likely faulty and should be replaced. You can get them at partselect.com ... Dishwashers

BOSCH Dishwasher Problem I have a dishwasher (SHV46C13UC/33) that when I start any of the three cycles it continues to run until I open it and do the 'cancel' function. The 'rinse/drain' seems to be running fine, but there is a film left after that mode. I've checked the water inlet, which is open and fine. And, it does drain properly. Is there a SENSOR I need to clean periodically? Or, is the man control module the problem? What's going on?


I would check the float switch in the bottom should be a mushroom shaped thing that turns the pump off after the water level in the machine has dropped to a certain level or has totally emptied. ... Bosch 24 in. SHV46C13UC Free-Standing Dishwasher

I have a Bosch shy56a05 dishwasher. It seems to be in a stall. IT will not run through any cycle. Also it used to turn off (meaning the buzzing etc) when I open the door, now it does not stop working (buzzing)when I open the door. Any ideas?


Hi.If the machine is cycling , and pump does not stop when you open the door, then to start, either the control board or the door latch micro switch is faulty.If the machine already started having different problems, like buzz ... Dishwashers

Motor runs when door is open- water does not come in- seems stuck


Depending on the brand and mdl the unit may be equipped with an overflow safety. If ther is water under the dishwasher in the floor pan then the sensors will trick the dishwasher into thinking it is leaking. Check under the kick plate . if it is moi ... Bosch Integra® 500 SHX46A0 Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1980 seconds