Having problems with your Bosch 24 in. SHX46A02 / SHX46A06 Built-in Dishwasher ?

The washer won't complete it's cycle. It just runs and runs. One time I got it to complete by turning it off, then switching to the Rinse and Hold cycle, but now nothing works. It doesn't drain the water, it appears to be stuck in the wash part of the cycle.


Answers :

Repair Help & Product Troubleshooting for Bosch 24 in. SHX46A02 / SHX46A06 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The washer won't complete it's cycle. It just runs and runs. One time I got it to complete by turning it off, then switching to the Rinse and Hold cycle, but now nothing works. It doesn't drain the water, it appears to be stuck in the wash part of the cycle.


... Bosch 24 in. SHX46A02 / SHX46A06 Built-in Dishwasher

I have a Kenmore Ultra 15895 or 15891. It fills with water then doesn't run. It will continue through it's cycles, but stays full of water. If I hit cancel before it completes the cycle, the number 2 shows in the display and nothing happens. If I let it complete the wash cycle, it will sometimes start and wash properly.


HI. The culprit will be the main control sector. This control fault may possibly be corrected by initiating a hard reset. the logic chips are scrambled, and this damage may be correctable by simply unplugging, or shutting off the appropriate circuit ... Dishwashers

Jackson jp-24b purchased this machine used, cant figure out how to work it. I flip the auto cycle on, and then the power switch. The fill light turns green and i assume water is filling up in the machine. In the meantime there are two small red external hoses that hot water comes and i currently just have those hanging in the sink. At the same time, nothing is happening during the wash cycle, the wash gauge doesnt even move only the rinse gauge. Also when i try to drain it nothing happends (begi


It needs a new drain relay box 120 volt the drain is stuck open the jp 24 were not very good machines the red lines are drain lines if you plug up the drian lines at fillup the machine will wash but now it will never drain a new drain box is not c ... Jackson JP-24B Built-in Dishwasher

ETNA ENF 18500A/5 type: 3.E1.181213221110 36 VLENNL 5 Dishwasher lights are on, and set for running, but the dishwasher does not do anything. Sometimes it makes a slight hum when closing the door, but most of the time, nothing. It stopped running after standard dish washing liquid was put into the machine by mistake. At that time, the machine started and ran through part of the cycle, but did not complete, and did not drain the water. Since then it has not started again. I have remo


... Dishwashers

Hello, I had a problem with my Bosch dishwasher not washing properly. I have fixed burnt out wires, replaced the water inlet valve, AND tested with a new control module. Nothing is helping. When I start the cycle, it completes the initial drain and water does flow into the unit for about a minute, maybe a minute and a half. I can hear the clicking of cycle changes but it is not washing. Eventually it will drain the inch or so of water in the bottom, but it never washes. Any help???


Hi,\015\012\015\012Welcome to Fixya.\015\012\015\012Can you hear the wash motor humming ? I`ve got a "pdf" I can send you regarding this if you want to contact me at ... Bosch SHU9925UC Built-in Dishwasher

I have a Bosch dishwasher that is about 4-6 years old (model SHU8805UC/U12). A few days ago I found clear water in the tub hours after the wash cycle had completed. I drained the tub by resetting the cycle as instructed in the user manual, but the tub gradually filled up with water again after several hours.. will replacing the inlet valve solve this issue?according to what I can tell for my model the water valve assembly (part No. AP3783031) is the part I need. How difficult and expensive


Just pulled mine out last night. You have a different model but it should be the same. Remove the bottom dress panel and detach your inlet hose from the water valve assembly (have a rag handy to catch a little water). Two torx screws on the front ... Dishwashers

Bosch Shu43C02UC dishwasher fills with water but the washing won't start. As the filling nears complete, a double clicking noise occurs to start the washing motor but nothing happens. The time continues to countdown but the machine is silent. When I open and close the door, the click click noise is heard but the machine is silent. I can cancel the cycle and drain the water but none of the washing or rinse cycles will activate but the timer works. The soap door even opens if the timer is left to


Have you checked the inlet water temperature is at the correct level for the dishwasher.\015\012\015\012Please provide the full model no. of your dishwasher -- Shu43C02UC /??\015\012\015\012I think the problem is linked to th ... Bosch 24 in. SHU43 Built-in Dishwasher

My kleenmaid dishwasher super silent model system DW5 doesnt appear to be heating the water on any cycle so it is not washing properly and leaving the powder etc on the glasses up the top particularly and also it does not go completely to the end of the cycle by itself(any cycle).Or completing the drying cycle. I have to switch to 0 cycle to make it complete the clicking to start again. What is the gauge on the inside of the dishwasher on the left that can be adjusted from 1-5 is this a heat


Http://frigidaireservicetips.com/pdfs/486_5.pdf\015\012\015\012\015\012\015\012Service manual, generic, use this to troubleshoot and repair.\015\012\015\012 ... Dishwashers

When starting wash cycle the dishwasher cda cw447 doesnt appear to be getting enough water in and is making a droning / whirring / electrical ? noise. pipes all connected ok inc aquastop water supply unit, no kinks etc. machine 3 1/2 yrs old, just started making this noise. appears to complete rapid cycle but still making unusual sound. water drains away fine from this cycle, dont believe pipes / hoses are blocked.


Try removing the inlet pipe, and refitting, might fix it, else likely that the \015\012Inlet water soleniod failing/failed or tiny mesh filter (it does come out for cleaning) behind the inlet hose clogged. Temporaily bypass the aquastop water s ... Dishwashers

Large amount of water remains in tub after completion of wash, water is draining out during cycle, dishes are cleaned, I can hear water being pumped out into sink drain as dishwater is going thru its cycle. The depth of the water is over one inch at the lowest part of tub. Water is not clean and has soap in it.


Hi.To start check the drain well, and also have a look at the drain hose at the back of the appliance.If the drain lines are OK, then you will need to replace the pressure switch, that determines when to stop pump from drainin ... GE Dishwashers

Water is running in and draining right back out. Leaving the dishes completely dry and dirty. I found a part laying on the floor when I took the cover off. I put it back where it came off of and now this problem. Yesterday it was the water not draining at all, now after putting that part back on it drains and doesnt wash.


Was it the float? try this empty machine put 1cup of vinegar or CLR and let it run through machine and clean jets and spray arm as well as soap dispenecer,You may want to try cascade they have rechanged it .Try this and let me know thanks ... Crosley 24 in. CDU600 Built-in Dishwasher

Machine starts fills Ok but when it clicks on to start the wash pump, nothing happens, I can hear a faint hum. When cancelling wash and starting new wash it pumps out ok too. After rinse cycle it indicates a completed wash, but no water has been pumped through washer arms.


Sounds like your main circulation pump is not working, if it is humming when it is supposed to start, sounds like it is getiing power, so probably not the control circuits, can you measure voltage to pump?if you are getting 120 there, probably pu ... Asko D1876 Dishwasher

I have a GE Triton XL dishwasher that is not spraying water onto the dishes. I just reset the power, and that didn't help. Putting it on the rinse only or wash cycle fills the bottom with water, but it sounds like a trickle vs. the spray. The heating element comes on and the soap door opens, but there's not spraying. I made sure there was nothing clogging the water line or other parts. What do you think is wrong?


... GE Tritonr XL GSD6260JCC Dishwasher

Westinghouse Virtuoso 922 dishwasher. Wash cycle completes, but water does not drain out. If I let the cycle continue, after a delay the rinse cycle starts, but of course no clean water is pumped in so the dishes are "rinsed" in the dirty wash water. The wash cycle itself is successful with water pumping all around the washer if I open the door mid-cycle. I have removed and cleaned all filters which were correctly fitted so I am confident there is no foreign matter inside pump. When the water sh


... Dishwashers

The dishwash is not washing, it's running but there is no water. The washing cycle is completed but nothing has happen, this recently started.


Sounds like a bad water valve or the water supply is cut off. If the water supply is not cut off then try hooking up 120 volts to the water valve. It should buzz or hum and let water in. If no water goes in then change the valve. ... Dishwashers

I have a Miele Turbothermic dishwasher which is nearly 3 years old. The Inlet/Drain (red) light is flickering and the washing cycle was not completed. I cleared the strainer but have not been able to clear the the dirty, stagnant water. I tried re-starting it with everything out of the washer but nothing has changed. Is there a way to clear the water and get this machine working again? Many thanks. Loretta


Please provide the full model number of the Miele dishwasher.\015\012\015\012Have you checked that there is no blockage in the kitchen drain especially if you use insinkerator (disposer unit) in the sink. ... Miele Dishwashers

KUDS30IXSS1 dishwasher will pump out water completely on the one hour wash cycle, leaves water in tank at end of all other cycles. Will completely drain when cancel/drain cycle is pushed. Is there a re-set code, or sequence; or is there a diagnostic code or sequence tohelp me? Like push Heat/dry, then normal wash, then Heat/dry, then normal wash within 6 or 7 secs? Or is my circuit board just shot?


... Dishwashers

Subject is Bosch dishwasher SHU6800. There is a soap residue left on dishes. Residue is not visible. Using two glasses taken from a recently completed wash cycle I rinsed one under tap water and then filled glass with tap water. The second was just filled with tap water. There is noticeable soap bubbling and foam in the second glass. Starting the 10 min rinse/hold cycle following completion of a full 60 min wash cycle results in considerble soap foam in the bottom of the tub. Have tried thr


WHAT IS WRONG WITH YOUR DISHWASHER? \015\012\015\012\015\012\015\012 \015\012For a detailed Dishwasher ill ... Dishwashers

Hotpoint dishwasher machine go's through wash cycle, through to the end, after dry cycle ends there is always 2 inch's of water left in it that doesn't drain out' but some water is added when new cycle is started, then throughout wash cycle whenever water drains it never drains completely, always leaves 2 inches of water before adding more water to begin rinse cycle. what do I need to do?


... Dishwashers

Kenmore dishwasher My Kenmore dishwasher model 630.16302401 is not successfully completing wash cycle. When I hit "normal" and turn it on, water enters the d/w, and the sprayers (both top and bottom), spray water. Approx. 10 mins. later, the water is drained. At that point, it appears that water never again enters the d/w to complete the wash cycle. In fact, the soap in the dispenser does get released, and the door opens. However, the soap will just run down the inside of the door and pool on th


... Maytag Dishwashers

Kenmore elite dishwasher model 665.13153k701 At end of wash cycle, water does not drain completely. Intemediate drains during wash do drain completely. rinse and hold drains completely. watching water at end of wash thru disposal, water flow cuts off like valve closed. other drains taper off


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

When dishwasher is turned on to the cycle mode - it fills with water - heater heats water to the proper temp - pump starts - washer goes through it's complete cycle - even pumping out the wash water and the drying cycle,then shuts down. the problem is that it does not circulate the wash water thru. the spray heads-even though the circ,pump is running.Even though the unit is 8 yrs.old and hasn't run for 6 yrs,my wife&i do our dishes by hand. our unit is a GU1200XTKB0 Serial# FL4617501


The impeller on the wash pump is worn out or the disposer screen is obstructed. Disassemble as needed to investigate the cause. ... Whirlpool 24 in. GU1200XT Built-in Dishwasher

Washer goes through complete cycle but doesnt totally drain. there is about 1 inch of dirty water left in washer. this washer is over 1 year old, kenmore ultra wash


Make sure your Drain Pipe is properly fixed . any Blockage in the Drain Pipe Creates the above mentioned Problem ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

After wash cycles are completed there is about 1/2 gallon of water remaining in the bottom of the washer. I checked the drain that exits into a disposal and that is clear. All around the bottom of the washer base is clean and I can find no obstruction. Nothing in the owners manual gives me a clue as what else to do. I don't want to start taking things apart unless I have to.


Hi and welcome to FixYa. I am Kelly. Most dishwashers are connected to the sink / garbage disposal via an Air Gap. The Air Gap gets debris inside it that blocks the drain passages. Check out this video on how to clean it: ... Maytag 24 in. MDBH950AW Built-in Dishwasher

New dishwasher (Beko 2542F slimline model). Put it on for 1st time last night -when I got up this morning, the cycle which should have taken just over 2 hours hadn't finished. There's soapy water in the bottom of the machine which hasn't drained and the "wash" light is still on. Looks like the dishes are clean but hasn't moved onto the rinse/dry part. Followed instruction in manual to drain it (hold start stop button till lights flash and should drain in 45 sec) but nothing happened.


... Beko Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2152 seconds