Having problems with your Bosch 24 in. SHX46A05UC Built-In Dishwasher ?

I have a Bosch SHX46A05UC/33 5-cycle dishwasher whose labels on the cycle buttons have also worn away. While the Macmarkus post was helpful b/c I have some of the same buttons, can you tell me the labels of the five-cylce buttons? Sue A


Answers :

Hi,
\015\012
\015\012Some SHX46A washers have 4 cycles and others have 5 cycles.
\015\012
\015\012I'm fairly sure your model has the hidden buttons on the top of the door and you stated you have five-cycle buttons, in which case they will be as follows.
\015\012
\015\0121. Top Rack only cycle or Sanitize
\015\0122. Power Scrub Plus
\015\0123. Regular Wash
\015\0124. Delicate Wash
\015\0125. Rinse and Hold.
\015\012
\015\012These buttons are also used for cancelling a wash cycle. Hold down "Power Scrub Plus" and "Delicate" at the same time to cancel a cycle and drain the water out.
\015\012
\015\012If your washer does have 4 buttons, it means you don't have a Top Rack / Sanitize cycle, in which case the button configuration (from left to right) will be:
\015\012
\015\0121. Power Scrub Plus
\015\0122. Regular Wash
\015\0123. Delicate Wash
\015\0124. Rinse and Hold.
\015\012
\015\012I hope this solves your problem. If you need any additional information, please post back.
\015\012
\015\012Regards,
\015\012BElectric
Repair Help & Product Troubleshooting for Bosch 24 in. SHX46A05UC Built-In Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Bosch SHX46A05UC/33 5-cycle dishwasher whose labels on the cycle buttons have also worn away. While the Macmarkus post was helpful b/c I have some of the same buttons, can you tell me the labels of the five-cylce buttons? Sue A


Hi,\015\012\015\012Some SHX46A washers have 4 cycles and others have 5 cycles. \015\012\015\012I'm fairly sure your model has the hidden buttons on the top of the door and you stated you have five-cycle buttons, in which case ... Bosch 24 in. SHX46A05UC Built-In Dishwasher

I have a maytag dishwasher mdb5601awb. when I hit the start button nothing happens. I have found the instructions to do a manual test which is hitting the heated dry button 5 times and then the start button. Thinking it will run some test which I have no idea what to look for, it actually runs the machine's wash cycles and clean, dries and tells me it clean with the green light goes on. How do I reset/reboot the machine so it starts by just hitting the start button again?


... Maytag Dishwashers

Dishwasher does not start, on any cycle selection. the only button that works is the cancel button which tells me the unit has power. this has happened before and a service tech was called and it "magically" started after he pushed the cancel button, not so this time??


Make sure the floor is dry where you are standing. \015\012 \015\012Push the cancel button twice in quick succession to attempt to turn the washer off.\015\012 \015\012Open the door all the way and look over t ... Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher

Bosch dishwasher SGS46E22. Making strange noise as soon as the appliance is switched on and cycle not progressing or progressing very, very slowly. Ran test cycle (held in Auto and Eco buttons together and pressed start) - E6 appeared in display. Suspect pump or motor problem - how do I tell which needs replacing? Thanks.


... Dishwashers

I have a kitchen aid dishwasher model # kudso1ij and it just blinks the rinse cycle button. if you try to push the cancel button it won't work. when you close the door it blink the 2 for just a brief second then goes back to the dashes. One night it just started on its own. Can you tell me how to reset it or fix this problem.


... KitchenAid Dishwashers

Overload button could you please tell me where overload button is on a nouveau dishwasher got stuck mid cycle now wont run properly


If it is stuck you can turn of the power at the electric box for 5 minutes and the restart it . this should reset the systemhuumplease remember to leave a good rating ... Dishwashers

My Miele G641 displays the Salt PC light even after filling it with salt. I have to cycle the main power switch 3 or 4 times before the Start light will come on. Then when I press the Start button it momentarily pumps out water and then stops. Sometimes the Start light stays on and I can get it to give the pump another brief spurt, but often the Salt/PC light comes on again and the Start light goes out. I then have to re-set the power switch. How do I tell if the logic board is fried?


Hi.This is not a PC, when logic board is fried the machine does not start at all rather than doing weird thing.The logic board is not fried, in the worst case the salt sensor is jammed. Try first pouring a couple of litres of hot wa ... Miele 24 in. Novotronic G641 Plus Built-In Dishwasher

Labels have worn off operating buttons from my Integra model. can you tell me what they are supposed to say?


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

I have a Bosch SHX43M05UC Dishwasher. To wash, you select the cycle and then close the door to start the wash. Now when I push the on button, the pump turns on. I can't tell if it's pumping water or not but it's not supposed to start until the door is closed.


... Bosch SHX43M05UC Built-in Dishwasher

Control Panel The control panel labeling on our SIEMENS hydroSensor, SL84A305UC/01 rubbed off right away and no one remembers which wash cycle is which. This dishwasher is in a Fire station and has multiple users. The quality of cleanliness is vital to our health. Please send or e-mail us a diagram of what the buttons are supposed to do. Thanks, B.Brewster


See:http://www.siemens-home.com/pdf/sl84a30xuc_manual.pdfThere is a pic with the buttons in there. ... Siemens 24 in. SL84A305UC Built-in Dishwasher

Maytag 24 in. MDB8951AWS intermittent button problems and incomplete wash cycle. The buttons work sometimes ... sometimes not. We also have experienced incomplete wash cycles when the buttons do let us start a cycle. Sometimes it completes correctly. Suspect control board, as I expect a membrane failure to cause incomplete cycle unless it is making a Stop/Cancel contact by itself. Can anyone chime in on thoughts?


... Maytag 24 in. MDB8951AWS Stainless Steel Built-in Dishwasher

I have a Kitchenaid Dishwasher M/N KUDS25SHWHO. Had to replace the control board because the unit would not start. Installed the new board and the unit now operates, but not correctly. Once in awhile on the Normal cycle, it will get a third of the way through the cycle and just stop. Used to be, you could hit any of the Wash Selection buttons and than any of the Options butons and then hit the Start button to begin the cycle. Now, as soon as you hit one of the Wash Selection buttons, the un


... KitchenAid 24 in. KUDS25SH Built-in Dishwasher

I used the "rinse only" cycle on the dishwasher a little while ago. I've never used this cycle before. After dinner I tried to start the dishwasher, but no other buttons on the panel respond except the last one I used, which is the rinse only cycle. I push and push, I tried pushing and holding, nothing works, I get no lights no anything. I've been using the "light wash" cycle for a long time and I normally just push the start button and the last cycle used starts automatically, so I wasn't a


Try un-plugging the dishwasher (check for cord under the sink) or turn off the breaker to it to re-set the control board. If this does not resolve your issue you may have a defective key panel. ... Dishwashers

Model #665.1746 The Smart Wash and Normal Wash buttons are blinking, and neither wash cycles begin when the Start button is pressed. The Cancel button drains and sometimes turns off the Normal Wash button from flashing, but it seems no matter what I do the Start button does not start any of the wash cycles.


... Dishwashers

Hi I have a problem with my Bosch SHU43CO6UC/22 dishwasher. using "power scrub plus" and "regular" cycles it will continue to fill and overflow the door, after the cycle has run even when the power button is off. I am using the quick wash cycle at the moment .After the cycle has run i open and check if the water has drained or not,If it has it does not continue to fill and flood.If there is water in the bottom after the cycle has finished it will keep rising untill I push the rinse hold button


The bosch dishwashers use a fill valve that is attatched to the inlet hose. yours is stuck in the open position. this usually happens when you have hard water, as the minerals build up on the sealing surface of the water valve. there is no easy ... Dishwashers

DU1145XTP The buttons don't all work--for a while the normal wash and heated dry were the only functions that worked--now the start button doesn't work. I took the panel off and clicked the door switch and held it and got all the cycle buttons to light up except rinse only and only heated dry in the cycles would light up. The delay buttons don't work and neither does start. Also the panel seems hot.


You need to replace the circuit board inside the machine, technically it is possible for you to do it, how long have you had the machine, if it is under warranty you can have it serviced without any cost or less cost to you contact Whirlpool ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

My Maytag steam dishwasher # MDBH980AWS won't do anything when I hit the start/cancel button. Nothing happens no lights go on. When I his the cycle select button only a few of the lights go on - steam clean, High Temp wash & Sanitize. The heated dry button, or the Heavy, Normal, Light cycle buttons won't light up. How do I get it started?


My Maytag dishwasher # MDBH950AWW wont turn on no light but it has power in the outlet no power to the control board ... Maytag 24 in. MDBH950AW Built-in Dishwasher

I have model GU3600XTSY2. Sometimes the pots and pans light flashes for no reason. Sometimes I can push that button and it stops. However, the cycle I select to wash the dishes is constantly interupted by the pots and pans (P&P) light flashing. If I push the P&P button, the wash cycle usually starts where it left off. Sometimes it will go back to the beginning of the cycle and begin all over again and get caught in a loop; start washer, P&P flashes, push P&P, begins cycle from beginning, P&


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Whirlpool dishwasher model GU2-400-XTB7 Problem started with display cycling through delay times. (1 hr, 2hr, 3 hr and so on.) Was able to cancel that for short periods and then it would repeat the cycle. Was able to run dishwasher by pressing different buttons. Then it would start a cycle but did not run full cycle. Now control panel doesn't work at all. When buttons are pushed, lights do not light up and nothing happens. Is stuck in lock mode.


... Whirlpool GU2400XTP Built-in Dishwasher

Kenmore 665.15912001 DISHWASHER RUNS BUT DISPLAYS ERROR MESSAGE Instead of displaying the number of minutes in the cycle when I push the cycle selector button and then the start button, it starts as soon as I push the cycle selector, without waiting for me to push start; meanwhile, it displays "_J" instead of the number of minutes in the cycle. It washes the dishes but not well, lots of food debris. Some people in this forum have described running a diagnostic on this machine; how do you do that


... Kenmore 15912 Built-in Dishwasher

I have an LG dishwasher Model LD-O5AW2 Benchtop. IT has been going perfectly until now. I push the button in and then the start button, when the wash cycle has finnished it wont empty until I push the stop button off and then on again. Then it empties and goes to rinse but wont come out of the rinse cycle, just keeps rinsing, until I turn it off and on again.Up until now its been a great little dishwasher. JOAN


... LG Dishwashers

In order to reset my dishwasher i was told to alternatively press the clean and rinse button. my dishwasher has no button that says clean, rinse, or clean and rinse. my button choices are as follows: Front: CANCEL and START/RESUME Cycles: HEAVY DUTY, NORMAL, LIGHT/CHINA, QUICK CLEANUP, or RINSE ONLY Options: PROSCRUB, HI-TEMP SCRUB, SANI RINSE, HEAT DRY/Lock symbol, 4 HOUR DELAY. Does anyone have the correct sequence for initiating the diagnostic cycle?


If you want to reset the computer in that dishwasher you can just unplug it for a half hour. if it is a built in just locate the fuse in the or breaker that the dishwasher is on and pull it for that length of time. ... KitchenAid 24 in. KUDS02FRSS Stainless Steel Built-in Dishwasher

Kitchenaid dishwasher model KUDS01FL I press normal cycle button and then start button. Normal button stays green does not blink and cycle does not begin.


... KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher

Dishwasher stuck on rinse cycle. Have three yo son who plays with buttons, but I've been unable to get washer to finish (rinse went for three hrs prior to me realizing it was still running). Tried the front panel buttons w/o effect other than able to turn unit off, but it resumes in rinse cycle. Turned power off to machine from circuit breaker ( w/ machine off) then restarted and still in rinse cycle. How do I reset?


... Miele G892SC SS Dishwasher

I have a Whirlpool Gu180 ESJQ with a blinking green start light. If I clear this light (hold the start button for 5 second to place it in the end of cycle) then I can get it to start another wash cycle. However, the next wash cycle ends with a blinking start button again and the dishes aren't dry. I had an appliance service man come to check it out and he could not detect any problem! Now I have a leak!


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1308 seconds