Having problems with your Bosch 24 in. SHY56A05 Stainless Steel Built-In Dishwasher ?

After working perfectly for years, I came home yesterday and the dishwasher had gone through it's whole cycle (including drying) but the bottom was fully filled with water. I emptied the dishwasher and tried to put it through a "rinse and hold" cycle to see if it would drain, but that didn't work. I pulled out the filter--it's clean as a whistle. Any thoughts? PLEASE?? thanks!


Answers :

Hi,\012
Here is a tip that I wrote that will help you with your dishwasher not drainingproblem...

Dishwasher Problems - Water will not drain out

heatman101
Repair Help & Product Troubleshooting for Bosch 24 in. SHY56A05 Stainless Steel Built-In Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

After working perfectly for years, I came home yesterday and the dishwasher had gone through it's whole cycle (including drying) but the bottom was fully filled with water. I emptied the dishwasher and tried to put it through a "rinse and hold" cycle to see if it would drain, but that didn't work. I pulled out the filter--it's clean as a whistle. Any thoughts? PLEASE?? thanks!


Hi,\012Here is a tip that I wrote that will help you with your dishwasher not drainingproblem...Dishwasher Problems - Water will not drain out ... Bosch 24 in. SHY56A05 Stainless Steel Built-In Dishwasher

I have a dishwasher that hasn't been draining properly. For a while I could hit cancel drain cycle again and it would clear 1/2-1 of water out. But now that doesn't always do it. Someone told me to take filter out and see if it needs to be cleaned. Otherwise we have no other sink/plumbing problems with other kitchen areas. Please help! one handyman told me no use to work on dishwashers they are just throwaway with parts/service being so expensive.


The advise you recieved is correct. You will need to pull the unit out of the cabinet and disconnect the drain hose from the rear. Then remove the cover, There is a filter inside. If its clean then its time for a replacement unit. You could have a ... Whirlpool Dishwashers

My SHE4402UC/36 dishwasher malfunctioned all the lights were flashing and the machine was trying to drain. The guy came out and replace the control board. The dishwasher now read 199 on all cycles except the rinse and hold, the santitized light does not come when its done. The repair guy told me the count down timers were flakey on the the Bosch dishwashers and it would learn my dishwashing patterns in time. So 6 cycles later the dishes are still damp at the end of the cycle-the length of the cy


Well its not baloney but it is cheesey. normally changing the module is the cure but it has to be programmed correctly. bosch has a recall so check it out and see because the recall is free and the tech is suppose to know how to program it. go to the ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Kenmore 17369 When cycle starts... it sounds terrible (crackly sounding).... doesn't sound like the water is coming into the dishwasher. If I add water to the machine during a rinse cycle...it will wash and drain on its own.... Then I hit cancel. Please help.. I can't locate the owners manual.. Do you know where I can get one.. I understand that you can open the bottom up and see if there is anything lodged in the bottom of the dishwasher. Please help! thanks Cheryl


The problem is your water inlet valve. If you remove the panel at the bottom of the dishwasher you will see\015\012either a copper hard pipe, or a flexible steel hose leading into the\015\012water inlet valve.BE SURE TO CUT OF ... Kenmore 24 in. 17362 / 17364 / 17369 Built-in Dishwasher

Draining problem Water left in dishwasher after end of cycle. Have a disposer, don't have a drain air gap that I can see. Tried to do a cancel/drain, showed 2 minutes ended and water still there. Disposal works fine. What is really interesting is that there is only two of us and at most we've only used the dishwasher thirty times since we had it. Of course- service plan ran out last year (July 07) Please help me. My name is Donna


There is a flapper in the drain hose just where the hose attaches to the pump assembly it has been know to get dislodged and cause a partial drain. With towels underneath hose remove drain hose and stick you finger in and see if it is free moving. ... Kenmore 24 in. 16539 Built-in Dishwasher

Dw44zp fithe bottom was full of water and would not drain, fixed the drain issue with new hose and clan out of basin. Next I restart the dishwasher to see it run and NOW the drain pump runs forever and wont go thru the cycles ??rst


... Thermador DW44Z Built-in Dishwasher

Dish washer does not drain after the cycle is complete. The last few months when the dishwasher is done their would be a small amount of water left in the bottom. It didnt create any problems but would smell after a few days. So we would just run the drain cycle and it would empty. Well i got home to and the wife said the it was really full. The water was dirty and when you run the drain cycle it didnt drain. She said the dishes were clean. So i cleaned the vent, and filled the sink with


Check drain hose and drain pump.End of drain hose must be in same level with machine.Try it. ... KitchenAid KUDR01TJ Dishwasher

I have the Siemens SL84A305UC Dishwasher. All of a sudden it stopped cleaning dishes, but everything sounds normal and it fills and drains water, and sounds like it is completing the cycle. In the past when I opened the door while it was actively washing the water would spray out aggressively. Now, when I opened it while it was supposed to be washing I see just a small amount of water coming from the bottom wash blade, and not even enough to turn the blade very far. I thought it was just a c


... Siemens 24 in. SL84A305UC Built-in Dishwasher

Hi, we have an aquarius hotpoint df61 and it goes through the cycle but does not drain out the last few inches of water and the wash is not as good as it should be, have unscrewed the plastic bit under the filter thing to see if there is a blockage there but nothing, have now taken off the top and side panel to try and get to the pump, currently on it's back but hard to access underneath and not sure how to remove the solid bottom of the dishwasher..please help!


... Hotpoint 24 in. FDW60 Free-standing Dishwasher

My bosch dishwasher will not reset after holding cancel and drain. It seems to want to run a cycle but will not...help please!!!


My bosch dishwasher wouldn't start up i don't know where the reset bitton is ... Dishwashers

My GE Nautilus dishwasher keeps PUMPING water "out" of the machine during the entire wash cycle. I have removed all covers in the bottom of the unit to see if anything is stock. Used vinegar and CLR to remove mineral deposits-- yet nothing solves the water being pumped out the drain hose.. what's next, please.. a solution !?!


If this convert-able dishwasher is permanently installed, you will have to take off the lower access panel to get to the pump area. If it is still in a portable configuration, it may be easier to lay the dishwa ... GE Nautilus 24" Built-in Dishwasher

Dishwasher won't drain. (Kenmore 3380957Rev A) It's been not draining that well for a couple of months, but then a couple of weeks ago, it just won't let the last inch of water out. --I can't see in the center area under the plastic to see if something is clogging it. --I tried running it on three different cycles to see if that changed anything (Pots and Pans, Normal, and Water Miser). No difference. It never seems to overflow, but when the cycle is over, it has a couple of inches of


The problem could be the pump, the drain hose or the timer. It will not drain if left to sit. The thing to try first is to put a cup of white vinegar in the machine and let it wash. This may remove sludge or scale blocking the strainer. 2nd take the ... Dishwashers

I have been interacting with Daniel about my Dishwasher Smart Dispenser problem. The last thing he had to say to me was that I needed to replace my drain pump. Before doing this, I would like an explanation of why a new drain pump will solve my problem since my dishwasher is draining just fine...it is my Smart DIspenser that is clogged up and not working ?? See the discussion here: Dear go4t9ers, There is a new Comment for the I would like to run the Smart Dispenser Purge Solution on


Ok first this is the schematic for your entire machine http://www.s ... Dishwashers

Dear Sir/Madam,I have owned a Beko DW450 slimline dishwasher for 13 months and used it only twice, i wanted to use it last night but when i switched it on the drain pump activated and would not switch off. I powered down the dishwasher to see if that would reset it but unfortunately when i started it again it did the same thing - drain pump activated but would not stop running, it is impossible at the moment to carry out a wash programme. Does anyone have any idea on this problem. Thanks, Patric


... Bosch SHU5315UC Dishwasher

My bosh dishwasher SHX55M06UC/46 will not drain. A new disposal was put in and the dishwasher drain plug was not punched out and the dishwasher was ran that way. Now it just holds water in the bottom. I've tried resetting or canceling the wash cycle but that doesn't work and the washing cycle works fine. I'm hoping there is a reset or a safety for the pump if it gets clogged.


... Dishwashers

My dishwasher will not drain after cycling. I have check the drain hose connected to the disposal. All is in good order the hose is not cinked and the air hole is unblocked. I have also checked the screen at the bottom of the dishwasher, there is no debris or blockage here either. I can run the dishwasher on normal, it cycles but I still have stagnat water left beneath the bottom rack. How do I check my pump to see if it is working or could it be a short of some kind? It is a Kenmore Quite


The problem is a solenoid under the unit. It is a small black cylinder that operates a valve to change from the wash cycle to the drain cycle. You can probably order a new one from Kenmore for pretty cheap. ... Kenmore 24 in. 15252 / 15254 / 15259 Built-in Dishwasher

GE GHDA485N 10CS Dishwasher that has standing water in the bottom after the cycle completes. I pulled it out and reconnected power and ran a rinse cycle. I could see that water was pumping out the clear drain pipe but there was still about an inch of standing water in the bottom. Any thoughts as to what part has failed. Does the system use a water level switch or a timed drain cycle to determine when the water has pumped out. If it is a timed cycle could a slow drain cause the problem. Thank you


... GE Dishwashers

My Dishwasher starts, then stops after 30secs and won't continue draining. Everytime I turn it back on it comes up on the steam cycle and won't go to any other cycle, drains for 30secs and stops again. Power light is flashing. Have tried holding power button down for 10secs with no effect. Filter is clean, pipes are straight-no kinks. How do I get it to start working again? It is a whirlpool dishwasher, ADP5550.


... Dishwashers

Not draining caloric dishwasher is not draining...was working fine before i stopped it mid cycle to take out a glass...then the next time i used it i put it on the pots and pan cycle and after it dialed to off i opened up and found a "block" of detergent and it hadnt drained... i just put it back on the normal cycle and am trying again... we'll see ?


Does the motor come on when it is supposed to drain? If it does then by stopping the unit mid cycle you could have had a freak instance of food particulate blocking the air gap located on the back of your kitchen sink (if you have one) It would loo ... Caloric 24 in. CDU210C Built-in Dishwasher

I have a hotpoint dishwasher model# HDA1000G00WH. until recently never noticed rinsed water not drained after washing/rinse cycle completed. water level just above the drain cover. i removed the cover to see if i might find something clogging the drain screen but found nothing. i removed the plastic water "return" line & it was not plugged. thinking about pulling the dishwasher out, disconnect the plastic line connected to the bottom of the dishwasher, then remove the "bowel-like" container wher


Take out the pump. You should find a broken rubber flapper indide blocking the outlet tube. Cheap to repair. ... Hotpoint 24 in. HDA3740G Stainless Steel Built-in Dishwasher

WE have a LG dishwasher model LD-14AW3. It recently stopped working properly and stopped draining the water. WE called our dishwasher repair man in and he said he thought it would need a new board and we would be better off to discard the dishwasher.I took the dishwasher downstairs to discard but left it there for awhile as I still had reservations about it. I took it in and hooked it up again it worked very well doing the whole cycle. We brought the dishwasher back up into its place and it con


Hello, welcome to FixYa.\015\012\015\012The OE code is designed to indicate an overfill error, however there has been a revision made on these dishwashers since they can often incorrectly display the error. I doubt if there is anything very serious w ... LG Dishwashers

I cannot figure out how to advance a cycle without having to go through the entire cycle. For example, I had a drain problem with my sink and the plumber put the rinse and hold cycle on for about 10 minutes; now every time I want to turn on the dishwasher it is in the rinse and hold cycle. How can I change it???


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012Your post doesn`t specify a model number, however on most Bosch dishwashers in order to change from "rinse & hold" to "regular" ( or any cycle ) simply turn t ... Bosch Dishwashers

KENMORE MODEL # 363.16222100 Hello - my dishwasher (model# above) is currently filled with H20 and will not drain/work. When the knob to select the dishwasher cycle to begin is turned, it just 'clicks' and does not engage the washing cycle. When I tried to just let it run the cycle as is to 'restart', it had an electrical odor to it., Currently the knob is at the 'Rinse & Hold-(Heated Dry Off)' part of the cycle and all dishes have been removed. I would appreciate any assistance available. Thank


Either the motor is locked up or the control failed. You will need a service visit. If it is over 10 years old, I would buy new. ... Dishwashers

Kitchen Aid dishwasher Model# KUDP01FLSS. 2 problems #1 Won't run unless you press in on the door and hold it for a few minutes then it runs through cycle normally. Problem #2 It won't drain water out at the end of the cycle when I open the door there is water laying in the bottom of the tub. I have checked the drain hose for clogging and it appears normal. I am able to remove the hose from the disposal and suck the water out of the tub using a shop vac this indicates to me that the drain is ope


... Dishwashers

Kenmore Dishwasher Model 665.11643300 Cycle will not run. Normal Wash light blinking Cancel light will also blink (but can be cancelled by holding button down) I tried shutting down the power and resetting at the breaker. I tried other buttons like Air Dry, etc to see if there was some sort of sequence Note* last cycle ran was rinse cycle many months ago - house has been vacant and dishwasher has not been in use.


I will look a bit further in detail about your dishwasher problem. I am assuming you have checked the inlet water tap to the dishwasher is turned on. ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2425 seconds