Having problems with your Bosch 24 in. SHY56A05 Stainless Steel Built-In Dishwasher ?

Need to replace on/off push button on Bosh shy56a dishwasher

\015 Push button broke, How do we remove the fascia panel to replace the push button\015

Answers :

Repair Help & Product Troubleshooting for Bosch 24 in. SHY56A05 Stainless Steel Built-In Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Need to replace on/off push button on Bosh shy56a dishwasher


... Bosch 24 in. SHY56A05 Stainless Steel Built-In Dishwasher

Unable to start dishwasher, only functioning light on the panel is the cancel/drain light. push that button the machine funtions for a minute or two and shuts off,also the light above normal wash is blinking. When the machine last functioned it would start with a very high decibel level.If its the circuit board I need an approximate replacement cost. Bob


If you go to searspartsdirect.com you can get the exact cost of the module. ... Dishwashers

DU1055XTPQ3 built in Dishwasher... panel has power "cancel" button when pushed you can hear the pump running but on wash the light blinks about 3 times and goes out, nothing happens. Is there a sensor or something in the panel that needs replaced? Jim


Hi\015\012\015\012First try resetting the dishwasher by pressing the AIR DRY button and hold it for 15 seconds. After this if it blinks again 3 times then the control needs replacement. Hope this helps...please post back for further assistance. ... Whirlpool Dishwashers

I have a Maytag QuietSeries 300 dishwasher. My original problem was with the control panel lights not coming on. Another repair website recommended replacing the circuit board. We replaced the board, but it did not solve the problem & the dishwasher would not work. Replaced the control panel. Lights come on, but when the start button is pushed "21" flashes on the time display. What do I do?


HI,Just visit this link HERE and your problem will be solved.Goodluck,Please don't forget to rate the solution. ... Dishwashers

BOSH DISHWASHER SHU5300: DOESN'T DRAIN COMPLETELY, WATER DOES NOT SIT ON THE BOTTOM BUT POOLS UNDER THE FINE FILTER. THE WATER HAS A BUILD UP AND THEN BEGINS TO SMELL. UCK!! I HAVE DONE ALL OF THE CARE & CLEANING POINTS FROM THE MANUAL. THE DRAIN HOSE DOES NOT HAVE AIR GAPS, THAT ISSUES WAS ADDRESSED. PLUS SEVERAL OF THE BUTTONS DO NOT WORK. THE BUTTONS DEPRESS BUT DO NOT FUNCTION. BEGINNING TO QUESTION IF I SHOULD REPLACE THE DISHWASHER? (10 YEARS OLD) THANKS FOR YOUR HELP!


Def replace .....time to put the old girl down ....whirlpool is a good choice ....or another bosh ... Bosch 24 in. SHU53 Built-in Dishwasher

Hello, We need some assistance with our Kenmore dishwasher. Last night after I started a load, the dishwasher just stopped and then the washing and drying lights started flashing red, sanitized and green are flashing green and the 6 hour delay button is flashing red. I have pushed the start/cancel button but to no avail. My husband shut the power from it to see if it would reboot, it does not help either. It runs a little bit then quits and does not clean the dishes. Could you give us sugg


Hold the start button for 3-4 seconds and see what that does ... Dishwashers

I have an Asko 1805 Dishwasher. I've looked at some of the other responses and have this sinking feeling after tonight's series of unfortunate events. Tonight, I pushed on the On/Off switch on the left and it appears to have broken. The dishwasher no longer turns on. If you push in and hold the button, the lights come on, but when you let go, they turn off. This appears to be Part 763255 on RepairClinic.com. I also need the overlay/decor insert across the top of the control panel which app


Hello Rick,\015\012 \015\012Welcome to FixYa.\015\012 \015\012The "very instructive, but poor resolution" info you've referred to in your post was indeed a previous solutio ... Asko 24 in. 1805 Built-in Dishwasher

Dishwasher will not start when pressing the start button. Timer light flashed numbers and went off. None of the lights and buttons work. Circuit breaker in electrical panel is working. Does the on/off switch need replacing, or is it possible a mini circuit board is bad? Dishwasher installed in 2000 and is used on the average once per week.


As it is nearly 10 years old i would suggest you replacing the circuit board. To test exactly we would need the help of an continuity tester and multimeter. ... Bosch 24 in. SHU53 Built-in Dishwasher

I have a kenmore dishwasher model 66516362300 and i just replaced the electronic control after replacing it flashes the pots and pans button if you push any of the other cycle buttons or cancel they start to flash too.


Yes, its the control panel (interface) that is bad, not the control board. Here is a website link to the one for your model. ... Kenmore Dishwashers

Whirlpool Quiet Wash Plus dishwasher Model DU920PFGZ3. Worked fine until I replaced the insinkerator and forgot to punch the drain plug leaving water standing on the bottom of the machine. I punched the drain opening, and pushed the cancel/drain cycle button. It drained fine but since no water comes from the spray arms. I have removed the arm all the way down..NOTHING!! Some research indicated it could be the water inlet valve. When the buttons are pushed, it cycles but no spray or water.


... Dishwashers

KUDP01ILBS6 Kitchenaid dishwasher Doesn't work, except flashing lights on front panel. I have the normal light flashing. When I push any other button the cancel light starts blinking as well. I replaced the fuse, the main control board inside and it still doesn't work. Push button panel next fix? This is getting expensive. Could it be something minor? The troubleshooting papers didn't provide much guidance.


The first thing I would check is if the dishwasher is properly connected\015\012 to power input. There is a junction box under the dishwasher. To get \015\012access to it you have to remove the bottom panel. The power cord should \015\012be connected ... Dishwashers

My kitchen aid dishwasher will not start I replaced the interface control board thinking that was the obvious problem. When you go to set the dishwasher to start some of the settings don't always light up then when you push the start button the lights will flash then start but it's not flashing and won't start. I get lucky once in a while and get it to flash then start. I don't know where else to look. I don't want to start replacing parts one at a time till I get lucky. My model # is KUDIO1F


Check all cables especially the ribbon cables from the user interface to the electronic control assembly as steam from dishwashings will create small amounts of corrosion and inhibit signals to and from these 2 components,unplug each,inspect,and reco ... KitchenAid Dishwashers

Matag MDBH940AWS dishwasher: Push start and light comes on but dw doesn't start - push again and light goes out but pump starts running but no water enters, push again , it shuts off ;; past problem never addresses is delay feature stopped working , no lights come on when delay buttons are pushed, so... control head in door replacement in order? Thanks , [email protected]


... Maytag 24 in. MDBH940AWS Built-in Dishwasher

Frigidaire Dishwasher gld2440reb1. After removing filters, cleaning and replacing them I had three flashing lights ie Sensing, Clean and Sanitized. all buttons were inoperable. after unplugging and reconnecting I had a PF or power failure indicator. after pushing the start button the PF went off but no further action from any button. Help!


Usually if you get a PF error that means you have received a power failure usually from the control board shorting out on this model. Typical reasons the control will short out is from either the circulation motor shorting or pump motor shorting. If ... Frigidaire Dishwashers

My KitchenAid dishwasher model # kudp01ilbl2 won't start. It is the first time we're trying to start it since we had our water heater replaced (three, maybe four days ago). Not sure how much that may matter. I tried turning off electricity to the dishwasher at the fusebox (overnight), but that did nothing. Normally, you just need to hit the start button and the washing begins. Now, nothing happens. The dishwasher is about six years old.


... KitchenAid Dishwashers

My KichenAid KUDS011 has functioned well until this morning. When I push any of the buttons on the keypad, nothing happens. I noticed there is still water in the bottom of the dishwasher from the last dish washing. Also, I've heard there is a screen or similar part in the bottom of the dishwasher that needs to be cleaned occasionally. I haven't figured out how to remove the bottom center of the dishwasher to access this for cleaning.


If the drain or screen are clogged, the machine may no operate.Unscrew the the 2 long screws on bottom, remove the basket, there may be a flapper under the basket, For pics, see here: http://www.contractorssolutions.com/dishwashers. ... Dishwashers

Kenmore dishwasher 665.13749K601 will not start. Wash selection button lights but pushing start button does nothing. I have had nothing but problems with this piece of junk.


... Kenmore Dishwashers

I need to remove a broken heating element from my Whirlpool dishwasher and install the replacement part. I was hoping it would just "pop" out and the new piece would push in, however, it seems that it is not that simple. I need instructions.


Depend on how the heating element goes through the tub you do have to go underneath (if it goes down through the tub in the front) or even remove the dishwasher from the cabinet (if it does it on the back of the dishwasher). The tub is made of ... Whirlpool GU1200XTLS Stainless Steel Dishwasher

Neff dishwasher our dishwasher is six years old and have had no problems till now . there is power to it but when you push the on button the impeller starts up even when the door is open , and it wont go through the cycle , its asif there is no water going in and it is not draining away i have checked and cleaned the filters but nothing, then pulled it out from undre the sink and it started working . i put it back , it went through the cycle then the next day it would'nt work again . do i need a


You have a faulty door switch. It can be replaced and may be available at youre local appliance parts dealer. ... Dishwashers

I have a Kitchen Aid KUDKO1ILBS1 which is constantly blinking clean. I have replaced the circuit board once because the capacitors were bulging blown out. After replacing the board the dishwasher has a mind of its own and will start when it feels like it. Now it will not start at all. Buttons do light up when pushed but it always retruns to blinking clean. Got a solution?


Hi\015\012 \015\012If the clean light flashes 7 times, pauses, then repeats...When the dishwasher doesn't sense a water temperature increase, it stops working and locks the functions (clean ligh ... KitchenAid KUDK01TK - Multiple Color Built-in Dishwasher

I added 3 cups of water to the dishwasher DD24DT top drawer as directed to check the rinse cycle. I pushed the start/pause button, I hear some noise, but the dishwasher does not completely turn on., there is an icon with two arrows, like a cycle symbol. I did not get a manual with detailed instructions so need help!


... Fisher and Paykel DD24DT Builtin Dishwasher

Our whirlpool dishwash is not cleaning the dishes very well so I pulled it out from the wall and un hooked the electrical and the water lines. After looking at it I hooked everything back together and I have no electricity or power to my washing machine. Is there a reset button or something on the dishwasher that I need to push?


I've installed many DW's and haven't seen a reset on one. Take in mind, not saying that they're couldn't be one, but I doubt it IMHO. I've been installing all appliances proffessionally for 10 years and it just doesn't seem like there could be one. ... Whirlpool GU2400XTP Built-in Dishwasher

I have a Kenmore Type 575-0 Dishwasher, model number 665.16033401, Style 16033. It runs trough the cycle, once the cycle is complete the clean mode light is on but most dishes are still dirty. I had someone here to repair this about a year ago. All he did was press alternating two buttons, which I have tried, it resets and lets you start a new cycle. However, the problem remains. Last time there was only button pressing involved, no need to replace anything. So, I would hate to have to pay ag


You need an electronic control and heating element ... Dishwashers

I have an electrolux edw5505eps dishwasher. The control panel start button does not function, the delay button does noy cycle thru the delay time. Does the panel need to be replaced?


Check out my thread on a similar issue. If your power button doesn't light and delay button does not light? Is the LCD screen display anything? check out my post several really good check lists. ... Electrolux 24 in. EDW5505EPS Stainless Steel Built-in Dishwasher

My Bosch dishwasher model SHE 4AM 16UC /03 is not washing correctly. All wash cycles ( regular/ quick etc) stop before completed There is dirty dishwater remaining in the tub. This happened also a couple of months ago, I can't remember exactly what I needed to do, but as I remember I needed to reset the unit, by pushing some of the buttons. please help


... Bosch Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2374 seconds