Having problems with your Bosch 24 in. SMU40 Built-in Dishwasher ?

Opened door on cycle, will not continue cycle after closing door

\015 I opened the door of my bosch smv4403gb/18 dishwasher during a cycle. i must have forgotten to close the door again and a couple of hours later i noticed the door slightly open. so i shut it expecting the cycle to continue. this did not happen and has been like this for over six hours. please help\015

Answers :

The most common problem for a dishwasher to not restart after the door\015\012being closed is a failed door latch interlock switch. Adjusting /\015\012repairing it is not too difficult.

Of course this assumes that the Dishwasher power circuit from the circuit breaker remains powered up.

Post back here if you are looking for more details.

Good Luck!
Repair Help & Product Troubleshooting for Bosch 24 in. SMU40 Built-in Dishwasher

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a GE Quiet Power 3 built in dishwasher. With 1 min. left in a cycle, I opened the door, removed an item, then closed the door again, but it didn't finish the cycle. The machine continued its single beeps to indicate the door was open. Reopened and closed the door. None of the buttons on the control panel respond. Have unplugged and left overnight, plugged back in, beeping continues.


... GE 24 in. GLD6500L Built-in Dishwasher

Opened door on cycle, will not continue cycle after closing door


The most common problem for a dishwasher to not restart after the door\015\012being closed is a failed door latch interlock switch. Adjusting /\015\012repairing it is not too difficult.Of course this assumes that the Dishwasher power cir ... Bosch 24 in. SMU40 Built-in Dishwasher

Bosch Shu43C02UC dishwasher fills with water but the washing won't start. As the filling nears complete, a double clicking noise occurs to start the washing motor but nothing happens. The time continues to countdown but the machine is silent. When I open and close the door, the click click noise is heard but the machine is silent. I can cancel the cycle and drain the water but none of the washing or rinse cycles will activate but the timer works. The soap door even opens if the timer is left to


Have you checked the inlet water temperature is at the correct level for the dishwasher.\015\012\015\012Please provide the full model no. of your dishwasher -- Shu43C02UC /??\015\012\015\012I think the problem is linked to th ... Bosch 24 in. SHU43 Built-in Dishwasher

My FDB2810Ldc1 dishwasher won't stop going thru the cycles. We have to open the door to stop it. When the door is closed again it starts and will continue for hours if the door is not opened again.


I tried this and it did not work I shut off the main breaker, and still continued now it fills up with water. itrn for 48 hours until i rubber band the door and I never turned anything on1 go figure I got rid olf a small perfect fine dishwasher becau ... Frigidaire 24 in. PLD2850 Built-in Dishwasher

My wife opened door during cycle. When she closed door it would no longer run. Looking at problems and recomendations on similar models, I replaced the board. Did not fix the problem. I have checked the fuse and the door switches for continuity and all seem ok. The only lights on the panel that come on are: under cycle- Pots & Pans, Light. Under Options - Heated dry. No other lights work and the dishwasher does not operate.


Hi,\015\012\015\012First off, sorry to hear that you replaced the control board for nothing..in hindsight. So if I understand what you're saying is this, You cannot select any cycles and the unit won't start...because the start button is ... Dishwashers

My 6 year old dishwasher seems to be washing continuously. This has happened since the electrics tripped out last week. Cycles continue on and on and don't finish. also I don't think it's heating up at all. When I open the door there is water in the bottom but not tonnes of it, close the door again and it continues on but you never hear the drying stage.


... Neff 24 in. S5543X2 Built-in Dishwasher

Hi, I have a Whirlpool ADG 7540, started to run normal cycle, water began to filter through, and then beeping continuously. When door opened, light is on left hand side of controls, on the spray water button. Close door and beeping continues, Please help.


... Dishwashers

Champion dishwasher we have a champion freestanding dishwasher at my church. after the cycle is completed, the pressure guage behind the washer still shows 25-30 and it contnues to spray water. not forced by the motor, but more like a stuck open fill valve. if i turn off the water and run it, then turn the water back on, the valve is closed and does not let water freely in. butif i run it with the water on, it will continue to spray in freely after the cycle light goes out and you open the door.


If you turn the unit off from the circuit breaker will the water still run?if so the guts inside the solenoid valve are worn.you can call champion and get a kit to replace the worn parts and its not difficult to do.hope this helps. ... Dishwashers

Have Whirlpool dishwasher Gold Series, Model GU9805CGB1 which stops part way through wash cycle with the led indicator blinks on the normal cycle.....if we ope nthe door and shut ...it continues until part way through rinse cycle...stops again....led indicator blinks again.....we open the door & shut and it continues....but then continues to run through the normal wash cycle continuously.....until we open the door again.....what's wrong???


Sounds like the door is losing contact with the door switch, first thing i would check is the door strike.Metal strike plate located on the tub itself that the door latch catches as it closes. its a spring metal striker, i would try bending it down ... Dishwashers

Dishwasher - Bosche - SHV43A03GB - When the main power switch is ON, even with the door open the pump/motor continues to run (ie. Stop-cycle does not operate). However, the wash-program itself does not run, even with the door closed (ie. No water entering the dishwasher, even though water supply is on and feed lines are clear - not kinked). It is like the program is 'stuck' and I cannot seem to get it to reset.


Your door switch is likely faulty and should be replaced. You can get them at partselect.com ... Dishwashers

Kenmore Ultra wash makes a loud vibrating noise during the rinse cycle. Early on the noise stopped when you opened and closed the door. Now the noise continues throuhout the rinse cycle.


... Kenmore Dishwashers

AEG Diswasher Model / Favorit 44080IM PNC 911925601/01 (located in UK) Wash cycle finish light flashes 5 times in sequence then starts again - please advise the meaning of this error signal ? History Machine started running immediately door was closed before any programme selected filled with water and main was motor runs and circulates water Water is not heated and detergent door has not opened Machine will continue to circuluate water until turned off If reset used then


1 blink is machine is having major power supply problem.the power supply board needs replacement.\015\012-----------\015\0122 blink is CCU error.that control board problem.\015\012-----------------\015\0123 blink is the CT error.that is ... Dishwashers

Bosch SHX46A (6 years old) Selected regular cycle, pressed On and closed door. Cycle did not start normally. Pump runs, but no water is coming into the DW. I confirmed the water supply line is turned on. I opened door, turned off On/Off switch, then poured water into drain. Then turned On/Off switch on. DW began pumping water OUT of the DW. Also, it doesn't matter if the door is open or closed - if you turn the DW on, the pump will run. I suspect a problem with the electrical controls, or perha


From your description, I doubt that the problem is door latch is the cause.\015\012\015\012The first thing that a modern dishwasher does before it begins to fill with water is run the drain pump.  It appears that this DW is not progressing ... Bosch Integra® 500 SHX46A0 Dishwasher

My soap cap remains in the closed position at all times. The clasp mechanism works fine, if I cycle through with the door open I can see and hear the catch release when it should. But the door remains closed at all times. I leave it open to run, and sometimes it's closed when the wash cycle finishes! Is there an easy way to take the cap off and clean it? Or do I need to WD-40 around it?


There is a little spring in there that flips the door open, just take the screws off of the side of the door, you'll see the broken spring by the door, make sure power is off to dishwasher ... GE Nautilus 24" Built-in Dishwasher

Machine cannot finish cycle and is stuck in pumping out mode. Only tiny amount of water in drain basin at bottom, no excessive water. Was set at 10pm, still attempting to drain 8am! Has no diagnostic dials or manual over rides so continues on whether door is open or closed, even if I switch off and on again. Possible related issue, recently finish at end of washes has been "grainy", far from perfect, surfaces slightly sandy feeling.


... Bosch 24 in. SGV43A03 Built-In Dishwasher

Soap dispenser The soap dispenser door does not open automatically as it should... stays closed throughout the cycle unless we stop the cycle, open the dishwasher door and then open the soap dispenser door any suggestions? This is a Maytag DWU 9200.


A wax motor controls the opening of the lid. Also a seal that fits around the latch lever may be deteriorating and obstructing the function of the lever. Follow the link below for images and part numbers with cost.\015\012Item# 1405...$20.30 ... Maytag 24 in. DWU9202 Built-in Dishwasher

Short in door,touch control all light up when door is partially open,but goes out when door is closed and unit will not work. kitchenaid dishwasher.when door is open all lights are on for the cycle you press,but if you close the door the lights go out and dishwasher will not work


You have a broken wire in the harness that comes up through the door. It will be found by carefully moving individual wires till the symptom is duplicated. Not an easy thing when all the wires are tied together and moving one moves several. Been ther ... KitchenAid 24 in. KUDI02IRBS Stainless Steel Built-in Dishwasher

Maytag model mdbtt70aww. After the end cycle. open the door and found detergent tab on the bottom and the main wash cover is opened. Maytag diswasher model MDBTT70AWW. Put dishes and so forth in the dishwasher. Put detergent tab and jet-dry rinse agent in the pre-wash section. and close the cover. Start wash cycle after done over door and found the detergent tab on the bottom new the heater. The cover to the main wash is opened. Dishes are are clean. Wish someone would tell me


... Dishwashers

My Omega Eurolux Dishwasher (mode: DW211P/1) won't stop cycling, It sems to get stuck during the wash cycle and continues for hours, until I turn it off. If I turn the dial to rinse it rinses fine. It doesn't seem to heat the water at all, there is no steam when I open the door. I have put a new heating element in, but this doesn't seem to be heating up at all. When I open the door mid wash cycle the element is cold to touch.


... Dishwashers

My whirlpool dishwasher type 280-2 detergent door will not open during wash cycle. Yes the compartment, springs and door are thoroughly clean. Will not open if I just close the door and remains empty. I'm wondering if perhaps I knocked off some random part that makes it open. So please tell me how darn thing opens and perhaps a pic of the parts so I could see if ones missing. Thank you for any help offered for this, its driving me nuts.


... Dishwashers

Close the Maytag dishwasher, cycle starts, but I noticed a leak! Dishwasher door can be opened by putting your fingers on the edge and pulling it open. Tried it again, door clicked, thought it was ok but still could open door with fingers. Emptied the washer, door locked. Put in a few dishes, same problem


Your problem appear to me like it come from your upper basket .\015\012pleas try 1st to ensure the basket goes inside\015\012untill the end it is important..\015\012 thank you ... GE Dishwashers

Good morning, I have a F&P dishdrawer ds605i (i think!) single drawer intergrated front. I dont know whats happened to it. The last cycle it decided not to empty the water out, so i manually emptied it. Now it seems stuck. All it does is run the fan. i can't start a new cycle. The start/pause button allows me to open and close the door as normal and i can hear the lid opening and closing.......... I have tried turning it off for a day at the wall switch. I have also noticed i can


Hi \015\012I guess the model no. you have sent is not correct,however given bellow are links from where you can troubleshoot your problem to your dishwasher which is related to your issue:-\015\012 ... Dishwashers

My Frigidaire fghd2433kf1 starting flashing PF occasionally. I would open and close the door and it would go away. It became more frequent until two days ago when the dishwasher stopped mid cycle and flashed PF. When I opened and closed the door, everything went dead and the dishwasher no longer works. It acts like it has no power coming into it. I checked the breakers and the wires connecting the power into the dishwasher. No luck. I replaced the control panel, but not the control board. It did


... Frigidaire FGHD2433KF Builtin Dishwasher

Item: Whirlpool Ultra Dishwasher Age: 3 yrs Problem: Not enough water to effectively wash the dishes. State: When the dishwasher is started, the fill valve opens as normal. Only about 1/2 the amount of water is let in when the pump turns on and the washing cycle begins. Opening the door shows that the water level does not reach the bottom of the float. When I close the door, the wash cycle begins again but stops after a few seconds. This is when the water begins to fill again. This time, the wat


Larry,The float is generally for overflow conditions and will interrupt power to the fill valve solenoid. If you are not filling completely in the time allowed by the timer, it is most likely a flow restriction in the water ... Whirlpool GU2400XTP Built-in Dishwasher

My dishwasher has stopped cleaning plates properly. It makes everything wet but at the end of the cycle the detergent block is half dissolved at the bottom. I have just run a cycle and opened the door during this. The bottom is full of soap suds and water and the top spray bar is dripping water after I open the door but when I close and then reopen a few secs later the top spray bar has definetly not rotated. The water is also not hot, this dishwasher is a cold fed only machine so I guess the el


Hi, \012 \012I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms onli ... Zanussi 18 in. ZSF4123 Slim-Line Free-standing Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0893 seconds