Having problems with your Bosch ascents 300 ?

When washing dishes do lights stay on

No lights stay lit when washing dishes

Answers :

Repair Help & Product Troubleshooting for Bosch ascents 300

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We have a commercial Hobart dish washer Model # AM-8T2; Serial # 240461. We cannot get the wash temperature to go above 120' to 150' as the burner does not light. The pilot is on. A new thermocouple was installed but made no difference. The rinse temp goes up to 180'. How can we get the gas burner to light and stay on. Thank you. Gery Spory


Hello Gery - get the repairman back who installed that thermocouple as that repair includes making sure the unit is working properly. Most likely the thermocouple is simply not warming up enough to operate correctly. It may be that the pilot light ... Hobart Dishwashers

F&p dish washer mod dw60csx1 starts but won't wash, beeps 10 times and then 3 lights stay on, followed error code e5 all ok, but still won't washt


... Fisher and Paykel 23 in. DS603H W Built-in Dishwasher

We just bought a house that has a Kenmore diswasher model# 587.15173400. I started a load of dishes and the dishwasher ran for 1 1/2 hours. It stayed on the wash cycle and the sensing light would come on occasionally. I am not sure what is going on. Any suggestions?


... Kenmore 24 in. 15173 Stainless Steel Built-in Dishwasher

The clean light is staying on and we can't wash the dishes


Cut the power for 30 seconds to let it reset. ... Kenmore Dishwashers

I rinsed my dishes first, then i put in a tablet to wash the dishes ad never thought any more about it untill the following morning i went to empty the dishes and discovered that the dishes had not been washed and the tablet was still in its compartment, i also noticed that there is dirty water in the bottom of the dishwasher, on the panal there are two lights CHECK WATER, AND THE ACTIVE LIGHT is on, i would be very grateful if you tell me what is the problen. thank you ANNETTE BECK


Sounds like the drain is clogged, so the dirty water is not draining and the dishwasher won't cycle because if it did it would overflow (causing a mess). So I would suggest trying to remove the obstruction (could be food or a utensil, etc.... at the ... Dishwashers

I have a magtag quiet 100 series that has a broken handle but still shuts tight and seems to lock yet. Problem seems to be that the rinse only light will stay on for quite a long time and won't let me hit the wash button. When the rinse only light does go off, if I hit the wash button it starts but then switches to rinse only. Sometimes I can get lucky and get it to stay on wash after the rinse button is off for some time. Any suggestions?


... Maytag 24 in. DWD1500A Built-in Dishwasher

I have a maytag dishwasher and the light wash light stays on even after a wash cycle. Tried to press normal wash and goes back to light wash. What could be wrong?


I have had numerous problems with the conyrol panel on this particular unit. Runs about $95 ... Maytag 24 in. MDBH950AWS Built-in Dishwasher

I have the Whirlpool Quiet Partner 1 the wash cycle starts and about 20 Min.'s into it the clean light starts flashing or the the start light, one or the other each time and it wont dry the dish's anymore we have already replaced the panel once and it has always popped when it is filling with water or changing cycles. HELP!!!! I hate washing dish's and I am beginning to hate all Whirlpool Appliances.


If the clean light blinks 7 times thats you heating circuit. Test the heater with an ohm meeting to see if it has open. If so order the heater kit and it comes with the control board. ... Whirlpool GU2400XTP Built-in Dishwasher

AFTER RUNNING MY DISH WASHER I OPENED THE DOOR THERE WAS ST HALF IN OF WATER IN THE BOTTOM SO I WAS GOING TO WASH AGAIN BUT HAD NO LIGHTS ON CONTROL PANEL HAD POWER TO THE DISH WASHER BUT NOTHING WOULD LIGHT UP? DONT HAVE 10 WASHES WITH THIS UNIT .? MODEL #655-13443K900


Hi Bennie, Try http://www.manualowl.com for free PDF for troubleshooting the issue you are having. I hope this helps. ... Kenmore Dishwashers

My dishwasher will not start just these three lights are flashing at the same time. What should I do? The three lights that are flashing are smart wash , normal wash and cancel drain. The dish washer


Try turning breaker panel for that off, and back on. might just need to be reset. If that doesn't work, call the repair man ... Dishwashers

When I press the start/resume control, the dish washer start/resume light blinks 2 to 3 times, then turns-off. then the dish washer beeps several times; however, the dish washer does not start. when turned the breaker switch off and on, and then I press the start/resume control, the dish washer go through a normal wash cycle. The next day when I press the start/resume control, the same thing happens. 2 to 3 blinking lights followed by beeping for several seconds. Dish washer does not start


... KitchenAid KUDC10IXSS Builtin Dishwasher

Salt light stays on, dishes taste of salt


... Siemens 24 in. SE25T250 Free-Standing Dishwasher

Kenmore elite dish washer model 630.1390installed new kenmore dish washer and the power light always stays on,, is this normal


... Kenmore Dishwashers

Water not fully draining during washing dishes. Stays approx 2 inches.


I did check out the Drain Hose. It is not clogged. I also pulled out the dishwasher from the cabinet and replaced the Drain Pump. You mentioned the Drain Valve. How and Where can I check out the Drain Valve??? If I hit Start/Restart twice ... Dishwashers

Kenmore Ultrwash, limited wash cycles, dishes not the best clean, red drain light on during wash


... Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103

Water softener Salt residue remains on the dishes. The water softener is going throught salt like crazy. I fill the salt and make sure that the light is off before I start the cylce. Within the first 20-45 mins the salt light comes on again and the dishes will not wash properly. We have come to the conclusion that the salt is being distributed to quicky but cannot figure out why the light keeps coming on. The switch inside the cap for the salt is set a the min.


Just a thought, I hope the lady did not use table salt :-) ... Danby 17 in. DDW1802W Designer Series Built-in Dishwasher

Kenmore 665 17033400 Elite dishwasher clean light flashes 7 times and it wont run. i used the reset combination, all lights lit and stayed lit until i pressed reset. Then it started a wash. now the wash seems to be finished, though i am not sure and the clean light is flashing 7 times, pause, 7 times, etc.


That signals an issue with a faulty heater &/or heater drive circuit.(that info comes from their troubleshooting guide)I ran into it this weekend and discovered that the heater coil in the bottom of the washer was broken. ... Kenmore 24 in. 17032 Built-in Dishwasher

I have a Triton dishwasher. Last cycle, it completed washing then started drying and started beeping and the drying light is flashing. When I finally opened the latch, the beeping stopped, but the drying light is still flashing. The dishes were clean and warm - they air dried the rest of the way. I have not been able to get the drying light to go off. I have turned the breaker off over night, and flipped back on. The dishwasher goes back to flashing washing, and then clicks to drying and th


Hi,\015\012Make sure the salt level is ok - add 1Kg of salt if you have not done it in a while, and check rinse-aid level if apliccable.\015\012\015\012If this does nothing, then remove the lower kick panel for access to a data shee ... GE Dishwashers

Wash leaves a white film over dishes and wash / dry lights flash


The film is actually caused by hard water. There is a new product out at www.dishwasherfilter.com that solves this problem once and for all. ... Dishwashers

CDW60W10 Dishwasher - Drying light and rinse light are on and stay on and don't release tablet during wash


... Dishwashers

My Kenmore model 665.16022401 has the problem w/ the clean light flashing. I tried the bottom combo of hi temp wash, heated dry, high temp wash, heated dry and it re-set my dishwasher but then after I tried to run a new load it doesn't seem like it finishes all the way through because there is still soap left in the soap dispenser and the dishes arn't all clean, plus the green clean light begins flashing again. Don't know what to do.


... Kenmore 24 in. 16022 Built-in Dishwasher

Dishwasher is not drying. At end of cycle, dishes are still wet and damp, as well as the inside. Buttons are all pushed. Also, it seems to wash for more than one cycle. Did a light wash and after 1-1/2 hrs., it was still running. Purchased a couple of months ago. Dishes don't seem to be as clean as my old dishwasher.


Hi,Check your heating element.. A bad heating element causes many problems in dishwashers…Dishwasher Problems The ... Whirlpool MDBH969AWB Builtin Dishwasher

I have a Kenmore Elite dishwasher (model 665.1315), and the dishwasher will run through the wash cycle as expected, but when it gets to the heated dry cycle , it doesn't appear to dry. It will then flash a fault code 81 (8 short flashes of the 'clean' light, pause, and then 1 more short flash of the 'clean' light, longer pause, and repeat the code). The dishes seem to be somewhat dry, but there is certainly water on the dishes and on the tub (there is never any water standing in the tub, and t


Hi,Check your heating element.. \012A bad heating element causes many problems in dishwashers...Dishwasher Problems The ... Kenmore 24 in. 15932 Built-in Dishwasher

We have a Beko DWD5410W dishwasher that has worked fine...until today - the 'wash' light is on but it is not wasing. I have pressed in the 'start' button and held for 5 seconds to reset and it then springs to life draining out or whatever that noise is, and then if I turn the dial to a setting (even the cold prewash) and press 'start' again it starts whirring away, then after about 10 seconds just stops, with the 'wash' light staying on. Not blocked, I have checked - this likely to be a frozen p


... Dishwashers

I have a Whirlpool Gu180 ESJQ with a blinking green start light. If I clear this light (hold the start button for 5 second to place it in the end of cycle) then I can get it to start another wash cycle. However, the next wash cycle ends with a blinking start button again and the dishes aren't dry. I had an appliance service man come to check it out and he could not detect any problem! Now I have a leak!


... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1283 seconds