Having problems with your Bosch Dishwashers ?

We have a Bosch dishwasher. The manual says for models SHV46C13, SHX43C0 so I guess it is one of those. It stopped working and when I opened it there was a bunch of cloudy soapy water on the bottom. The power was not coming on at that point. I have noticed that lately when I go to push the on button, the light will go on and when I shut it it doesn't start. After a couple times of turning it off and on it will run normally. This has only happened a couple times though....


Answers :

Repair Help & Product Troubleshooting for Bosch Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We have a Bosch dishwasher. The manual says for models SHV46C13, SHX43C0 so I guess it is one of those. It stopped working and when I opened it there was a bunch of cloudy soapy water on the bottom. The power was not coming on at that point. I have noticed that lately when I go to push the on button, the light will go on and when I shut it it doesn't start. After a couple times of turning it off and on it will run normally. This has only happened a couple times though....


... Bosch Dishwashers

My Maytag dishwasher goes for long stretches when it won't turn on even though I push the proper buttons. The buttons won't light either. It turns on by itself after a couple of weeks of sitting idle. Some of the lights may blink on the start panel while the dishwasher doesn't work, but only on occasion will it fully operate. I have turned off the power and turned it back on, hoping to reset the computer part of the dishwasher. It didn't work.


The Control Touch Panels like to fail on may brands - especially Maytag. They are sensitive to humidity - and a lot have the vents out the front - right by the control panel.Please reply using "continue with this expert ... Maytag Dishwashers

The clean light on my kitchen aid dish washer kept blinking and would not stop. after reseting it by pushing the buttons 2-3 times it cycles though and stops. then nothing works when i push the buttons. model : kudpo2crbl4


The electronic control looks for a temp. rise of 2-4 degrees. If no temp.rise control assumes a heater fault and blinks clean light 7 times. Bad heater. Water fill when completed can be no less than 1/2 inch below heater. If so, water valve probably. ... Dishwashers

Kenwood Elite Dishwasher Mod#665.13779 K600 "Normal Wash " light blinks continuously with NO washer action. No other wash modes light up when pressed. Washer does not do anything. However, a couple of times I got it to make a noise as if it was draining, but then nothing happens. Push "Cancel" and it blinks in unison with Normal Wash light. Open door and close it, "Cancel" light goes out and Normal Wash light continues to blink. Have tried various combination of buttons to try to "Reset"


... Kenmore Dishwashers

I just bought this house with this dishwasher built in. I have pushed the door shut, pressed the heat dry button to lock the door and pressed the start button. Nothing happens. Now I can't even get the lights on front to turn off. The lock button flashes as though the door is open, but its not as far as I can tell. I have to press the latch in to open the door. I'd like to use it... any ideas. Its a Kenmore Elite model # 665 17052 402. Thank You


... Kenmore 24 in. 17052 / 17054 / 17059 Built-in Dishwasher

Dishwasher model# FGHD2433KBI. washer was purchesed mid July, used 4 times. I just put in some dirty dish's and closed the door. A couple minutes later the washer turned on. No lights were on. After a few minutes I pushed the cancel button. Nothing happened. I opened the door and it sounded like a sucking sound and the pump stopped. No water in unit. I closed the door it started again. I cut the power at the circut box. Waited a few minutes and turned power back on. Power failure light came on.


... Frigidaire 24 in. PLD2850 Built-in Dishwasher

One day the diswasher was working fine...the next time it turned it on it ran for about 3 min. then shut off and seemed to have no power. I checked the breaker...it was fine. A few days went by and all of a sudden the lights were blinking on the panel. So I pushed the cancel drain button. The water drained out and I then proceeded to load the dishwasher and turn it on again thinking it was just a fluke when it shut off earlier in the week. It did the same thing...ran for about 3 min and then shu


... Whirlpool GU2200XTSS Built-in Dishwasher

I have a Kenmore 665.1373 Ultra Wash dishwasher that will not work. In the past few weeks, it stopped mid-cycle, the the clean light began to flash. Sears sent out a technician who told us that the latch was not catching. He adjusted it, did something with a computer and the dishwasher worked for a couple of days. This time, it would not start a cycle, it would only show heated dry if you pushed the smart wash button and nothing if you press start. It looks like some of the lights are continuous


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Smeg Dishwasher Hello I have a smeg dishwasher - built in, push button. It has stopped working - the program start and you hear it drain but that's as far as it gets, no water appears to be getting in. A couple of times the last 2 program buttons flash or the rinse light is on when we open it. let me know if you have any thoughts on this - I'd really appreciate it. thanks Diane


Replace the timer/control board ... Dishwashers

Our AEG Favorit 50620 dishwasher won't start. When I push the power button, the power light comes on, but none of the other lights. Pushing the function buttons has no effect. The door is fully closed, and it was working perfectly before. I have tried turning it off and on, unplugging it etc. Nothing works. Interestingly, if you push more than one function button at the same time, some of the function lights come on, but then when you try to start the cycle it still won't work. Help!


... AEG 24 in. Favorit 40650 Free-Standing Dishwasher

Kenmore Elite Dishwasher, Model 665.15979992 No Heat Dry Button/Light: The dishwasher will not work. Have tried to no avail the various alternatives listed in this thread and others. Here's what the dishwasher is doing: To start off, the red light on the "No Heat/Dry" button is on - sometimes it's on steady; other times it blinks depending on whether other buttons have been pushed. Pushing any other button also causes the "Lock On" red light to come on. Pushing the "Cancel" button causes all


Have you checked the thermal cutoff switch located inside the door by doing a continuity test to it if this is sounding like where your problem are is coming from on this diagram ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have a Kenmore dishwasher, model 665.16039. Over the past month (we were on vacation 8 days over Xmas, but I assume it would have happened then, too) it has required rebooting using the Normal Wash - Heated Dry reset about 4-6 times. It would then do a couple loads okay, then need resetting. Now, however, it's refusing to reset to a point at which the Start buton will work. When I reset it, it flashes all the lights (incl. Start), and it fills, sprays, empties, etc. just as though it works


Make sure there is no water damage. ... Kenmore 24 in. 16039 Built-in Dishwasher

Electrical expert Replaced our dish detergent dispenser cup. Everything was fine with that. However, the display only lights up for two cycles and the start button is not functioning. We have re-done the two wiring harness pieces and shut the power off via circuit a couple of times now, but the problem remains. Any suggestions?


... GE 24 in. Profile PDW7800 Built-in Dishwasher

I have a hobart lx-g model which i purchased used a month ago. At the start everything worked great...then when ever i would push the "off" button it would shut down and restart by iteself... lately i've been getting lots of error msg's (one was E4...) and now it overflows all the time, its as if it's gone banana's... what do I need to do to fix my problems (chane the cpu???)


Hi,Initially would suggest to check that the power supply requirements are satisfied. You might also need to check the breakers. Depending on the exact model number, the AC supply can be as shown below: ... Hobart Dishwashers

I have a 8 yr old model 16879 that stops apparently during the drain cycle. At this point the lights on the panel flash in what appears to be a coded sequence. Pushing the cancel button seems to try to start the motor for draining but immediately shuts off. Do I have a controller problem or something in the motor/pump area? David


Hi,It could be either...I would tear into the drain pump first and verify that nothing is stopping it from turning, then go for the controller if that seems to be okay...\015\012Dishwasher Problems - ... Kenmore 16879 Built-in Dishwasher

My KitchenAid model number KUDSO2FR-SS hs blinking lights that won't shut off. The Pro Scrub light blinks on and off and won't shut off. I can sometime lock it out with the heat button but it lights right back up. After a couple of minutes the normal button starts blinking as well as the clean button. The dishwasher does not turn on. I tried unplugging it but it just reverts back to the same thing


... KitchenAid 24 in. KUDS02FRSS Stainless Steel Built-in Dishwasher

Maytag dishwasher mdb7601 will not run- light doesn't come on and nothing happens when you push the buttons. Earlier it would work but if you pushed the light cycle button the longer cycle would light up and it would run. Then the time running light did not light up.


... Maytag MDB7100AWB Dishwasher

THe ProScrub light is steady, and the dishwasher does not work. When I push buttons, the light keeps going off, and with the next button push, it goes on. If I leave the dishwasher like this for a while, then a couple of the other lights, I think the Normal and Heated Dry lights will blink continuously. In either state, the dishwasher does not work.


... KitchenAid 24 in. KUDS02FR Built-in Dishwasher

Our whirlpool dishwasher will only go on the light wash, just or a short time and then shut off. the other cycles, heavy and pots and pans will not go on at all. when we press the light wash button, both the light wash and rince and drain light all go on, for just a short time, then shut off. help!!


The membrane or touch pad is bad. Most of the time you need to replace the whole control panel. Usually one of the buttons has failed causing this symptom. ... Dishwashers

I used the "rinse only" cycle on the dishwasher a little while ago. I've never used this cycle before. After dinner I tried to start the dishwasher, but no other buttons on the panel respond except the last one I used, which is the rinse only cycle. I push and push, I tried pushing and holding, nothing works, I get no lights no anything. I've been using the "light wash" cycle for a long time and I normally just push the start button and the last cycle used starts automatically, so I wasn't a


Try un-plugging the dishwasher (check for cord under the sink) or turn off the breaker to it to re-set the control board. If this does not resolve your issue you may have a defective key panel. ... Dishwashers

Have a kitchenaid dishwasher KUDS25SHWH1 - the child-lock light came on and will not go off. It is a light and no button to push and hold except all of the select buttons for the type of wash you want, no air dry button. How do I get this light off?? The Child Lock light has come on by it's self and I cannot get it to turn off. I have never used this feature before. I have tried to hold the Energy Saver button for several seconds but the Child Lock light will not shut off. The dishwasher is loc


Unplug the unit for 15 minutes then plug it back in. This should reset all your computer system and make everything work again ... KitchenAid 24 in. KUDS25 Built-in Dishwasher

I have a kenmore dishwasher mdl#665.16022401the clean light blinks all the time and i push the cancel button and then wash and the start and the start button light blinks 3 times and nothing happens.the clean light is still blinking.


... Dishwashers

I have a magtag quiet 100 series that has a broken handle but still shuts tight and seems to lock yet. Problem seems to be that the rinse only light will stay on for quite a long time and won't let me hit the wash button. When the rinse only light does go off, if I hit the wash button it starts but then switches to rinse only. Sometimes I can get lucky and get it to stay on wash after the rinse button is off for some time. Any suggestions?


... Maytag 24 in. DWD1500A Built-in Dishwasher

I HAVE A WHIRLPOOL DISHWASHER AND THE LED LIGHT FOR CLEAN KEEPS FLASHING AND IF I PUSH THE CANCEL BUTTON IT PUTS IT IN TO A DRAIN CYCLE THEN THE LIGHT KEEPS FLASHING I CAN SELECT ANY CYLCE I WANT BUT WHEN I PUSH THE START BUTTON ITS LED FLASHES SEVERAL TIMES AND THEN STOPS AND THE CLEAN LED LIGHT STARTS FLASHING AGAIN


Check out it there is a water leak to the bottom housing. Usually this happens when there is a leak activated the flood sensor causing LED light turned on. Dry out the leak then leave it unplug for 24 hours so the sensor dry out by itself. Make sure ... Whirlpool Dishwashers

Matag MDBH940AWS dishwasher: Push start and light comes on but dw doesn't start - push again and light goes out but pump starts running but no water enters, push again , it shuts off ;; past problem never addresses is delay feature stopped working , no lights come on when delay buttons are pushed, so... control head in door replacement in order? Thanks , [email protected]


... Maytag 24 in. MDBH940AWS Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1377 seconds