Having problems with your Bosch Dishwashers ?

The tablet is still still in the door when the cycle has finished. It is wet and part disolved and the litle door has opened. I have checked the rinse aid and salt and cleaned the spray arms but they were clear. I always check nothing is in the way of the arms spinning. Any suggestons?


Answers :

It actually sounds like maybe the packet is getting partially melted to the inside. Have you tried washing with no heat at all? Or maybe change brands on detergent packets. The main thing is your door is actually opening all the way, if so, then the only other thing I could see being wrong is the tablets. Hope this helps.
Repair Help & Product Troubleshooting for Bosch Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The tablet is still still in the door when the cycle has finished. It is wet and part disolved and the litle door has opened. I have checked the rinse aid and salt and cleaned the spray arms but they were clear. I always check nothing is in the way of the arms spinning. Any suggestons?


It actually sounds like maybe the packet is getting partially melted to the inside. Have you tried washing with no heat at all? Or maybe change brands on detergent packets. The main thing is your door is actually opening all the way, if so, then the ... Bosch Dishwashers

Doesn't appear to be washing the dishes like the spray arms are not working. I can hear water filling and it does drain but soap is still on the door and in the bottom of dishwasher itself. Ran diag on it and it came back clear (0). I have a Bosch SHU5315U6.


Sounds as if the pump motor has gone out in the machine. What happens is once the water reaches a certain level the machine goes into clean mode. This means the pump the forces the water into the machine isn't working. The timer actuates this pump ... Dishwashers

Dishes don't get clean. soap still on inside of door. . . water coming up to fill line and hot enough and dishwasher drains after cycle, spray arms are clear. . . help!


Water from the wash arms must be able to reach the detergent cup during the wash. It sounds as though the machine may be over-loaded during the wash and water does not cause the detergent to mix with the wash tank water. Try washing a cycle with noth ... Dishwashers

My detergent is always still stuck in the dispenser. The water temp and pressure are both fine, the machine is clean as well as the spray arms, and the door opens but water just isn't dissolving it. I have tried powder, gel, tablets, and gel packs!!! Please Help!!!


Hi,\012There are three common problems that cause the Soap Dispenser or Cup not toopen. I have a tip that will explain these problems in detail....Dishwasher Repair Problem ... Magic Chef 24 in. DU2500 Built-in Dishwasher

Poor washing The soap door opens but soap still in there after wash cycle. We got lower spray arm off and one plastic piece but can't get all the way to the pump. Pump appears to possibly be cracked so we suspect it needs replacing, but we can't get it out.


Before you suspect the pump and motor assy, do you hang the silverware basket on the front side of the lower rack or if not did one of the holders for the rack fall off and you replaced it? I have found that id the basket is hung on the rack that tal ... Whirlpool 24 in. GU1500XT - Multiple Color Built-in Dishwasher

We used our LG diswasher to clean our grill grates, which was a bad idea, because now the unit will not clean the dishes. We cleared the washer arms of debris, but the unit still is leaving the dishes on both racks dirty and is leaving the liquid soap dispensed into the unit undissolved on the door of the unit. There are no kinks in the water inlet, and water is getting into the unit, but the dishes are not getting cleaned.


Hi\015\012\015\012\015\012Thanks for using FixYa. Please make sure the dishes are loaded properly or\015\012dishwasher is not overloaded. Also check that the dishwasher is filling\015\012properly. It will fill with water up to ... LG LDF6810ST Stainless Steel Built-in Dishwasher

I have a GE Profile, GSD4930X73WW, dishwasher. The upper wash arm is not spraying well at all. I checked the water line from the pump to the upper arm and it's fine. I cleared the filters and cleaned the float. I also took the inlet valve off and cleaned the screen. Although the washer works better overall, the upper arm still does not work well. Nothing appears to be in the upper arm assy to clog water from spraying out. All seems clear from the turbid sensor (next to the pump) through t


... GE Dishwashers

My power button cover broke on the dishwasher and I figured out the part number I needed, but when I put it back together I got the wires crossed on the board and door switch. Now the control lights up , but the dishwasher will not run a cycle. THe question is does the plug on the door switch have to be a certain way, because there are three wires and you can connect the plug both ways. I did turn the plug, but it still does not run. Did I break the switch? Bosch SHU9956uc/14


The wires do have to be a certain way on the door. Otherwise a door open can tell the board that's it shut and vice versa. The easiest way to do it, is test the switch with an ohmmeter, place the meter on the switch, push button in and see if the rea ... Bosch SHU9956 Built-in Dishwasher

Mod #: MDB6600AWB Ser #: 16505148CG No water comes out of spray arms, checked and cleaned filter-OK. Wash impeller is cracked where it slides onto the hexagon rod but it you take the filter flow plate off and put the impeller back on, when you put the unit on rinse only and quickly open the door you can see it is still turning and moving the water. The unit still fills and drains. it just does not have enough force with the impeller to force the water into the spray arms.


Hi,\015\012 \015\012Please check the bellow link regarding your query....\015\012 \015\012 ... Maytag 24 in. MDB6600A Jetclean II Built-in Dishwasher

Whirlpool ADG993, door fault: Hi, a few weeks ago soemthing broke on the door to my diswasher and it falls open wide with no stopping half way as usual. That was fine as the machine could still work, but now the door won't close. All seems fine until you get all but closed and then the door raises slightly from the bottom right corner, preventing it from closing. It looks like something may be jammed in there which pushes the door up at the last minute. There's a man coming out on Friday,


... Whirlpool Dishwashers

Prima lpr601 problem- filled dishwasher up sa normal set the wash pressed button on far right (dont know what it is but needs to be done), closed door and loud raattling so i opened door to make sure all spray arms were clear which they were, closed the door , again the rattling . now the green light has gone out on far right and cant get it back on so program wont start at all. Any advice?? please help


... Dishwashers

Hi I have a Blanco dishwasher BFDw8 which is having poor wash results in the top tray I have tried all the trouble shooting things in manual. Investigated further by opening door during wash cycle several times and discovered the top arm is not moving although water is still coming out of the arms. I did get a split pea particle out of the arm approx 2mm and have since had a mildly better wash and have used superior wash powder and rinse aid to try and help. Also have put a cleaner through di


\015\012\015\012Check the water temperature. Should be 125 to 140 F. \015\012\015\012Check pump re-circulation., Listen, see if it sounds like it is spraying the water around with enough pressure. ... Dishwashers

Frigidaire dishwasher 15 months old. just started not washing dishes very well. set it for high temp wash. put plenty of fresh dishwashing liquid in. the unit goes thru a full cycle. you open the door and dishes are still dirty. there is always lots of dishwash liquid in the door. some of it runs down the inside of the door of the unit. just does not use all of it so dishes dont get cleaned. what could it be?


First I would check to see if it is getting enough water. There is a screen in the water inlet valve that tends to pick up debris. Follow the links Di ... Frigidaire Dishwashers

Dishwasher, nautilus, doesn't spray water out the top arm? I'm haivng to wash dishes 2 times, and still no better results. I've tried opening the door fast during a water cycle to see which is the problem - can only figure it is the upper arm, the lower arm seems to have water coming out, can't tell if the tower raises completely up.


The jets on the arms can sometimes get blocked with food bits that have got past the filter. This reduces the water flow and rotation of the arms.The arms are easy to remove without tools (they are intended to be removed by the user). ... GE Nautilus 24" Built-in Dishwasher

Bosch Exxcel model number SGS46E12GB had the check water light on a week ago, checked supply and cleaned filters, all good. light still on, got upset and slammed the door, light off. since then the unit will either wash stuff, or not. didn't seem the arms were spraying very well when I opened the door, so I bypassed the door switch tonight and put it through a pre rinse cycle. (I ran it with the bottom filters removed) upshot is the pressure of water was really poor. also, when I first turned


... Bosch 24 in. SGS47E02 Exxcel Free-standing Dishwasher

The upper rack side rail is loose where it attaches to the side wall of the dishwasher. It allows the upper rack to wobble. When the dishwasher is turned on, the force of the water pushes the rack forward so it detaches from the water supply and the arm does not rotate. The arm and connection are all clear and the arm is able to rotate, so those problems are not a factor. The wheels are in good condition. The left rail is a little loose; the right one is very loose. There must be a way t


Hello melinda.... Here is a link to searspartsdirect.com ... Bosch 24 in. SHX46A02 / SHX46A06 Built-in Dishwasher

I have a maytag MDB600AWW dishwasher. the top spray arm doesn't turn. it wouldn't even turn if i removed the to middle trays. I took the accumulator out and cleaned it. the fine mesh filters were clogged. unfortunately, birthday candles found their way into the machine sometime back. i cleared as much as i could. when i put it back together, the top arm would spin only when i had the 2 middle arms disconnected. It seemed there was an increase in pressure. i ran a diagnostics test and there were


First check to see if the washarm itself is clogged, if so clean it out.\015\012\015\012If the arm has a bearing it may be shot.\015\012\015\012You may have a clogged manifold on the output side of the pump. I sometimes run a ... Dishwashers

The detergent dispenser [Main Wash] door doesn't stay closed. It seems like there is something wrong with the latch, but we can't what. We've cleaned it, but don't know what else to try. There don't seem to be pieces missing or broken. But no matter what, when we put in the detergent [we use the cubes] the door always just pops open and the detergent ends up falling to the bottom on the dishwasher. The dishes are still getting relatively clean, but we want to solve the problem with the door


... Frigidaire FDB1200RG 24 in. Built-in Dishwasher

Dishwasher Repair Dishwasher is a Stoves/Newhome DW616 Rotating spray arms do not always operate. This is an intermittent problem - will sometimes work normally for a few days then arms will not move at all with no water coming from them. Machine appears to go through its normal cycle. Some times cycle starts normaly and spray arms stop working part way through.


It could be a motor or a pump issue. The dishwasher has a motor that attached to a pump which forces the water up into the sprayer arms and during the drain cycle, it pushes the water out of the dishwasher. \015\012The motor (and pump) located beneat ... Dishwashers

It always seems like it never gets enough water to even make the spray arms work. I have even tried to make sure I am not running any hot water in the house. It is about 7 months old and has always acted this way. Could there be something wrong with the installation? My old Sears never had this problem.


Sounds to me as if there is a blockage in the water line supplying the dishwasher or a kink in the water line supplying the unit. Since the water is supplied from the angle stop under the sink there could be blockage at that point. What I would sug ... Dishwashers

3 PROBLEMS 1. SPRAYER ARM LIGHT ON BUT WHEN I OPEN THE DISHWASHER THERE IS NOTHING BLOCKING THE ARM FROM SPINNING. 2. SALT LIGHT IS ALWAYS ON. HOW DO I ADD SALT. 3. I NEED NEW TRIM FOR THE OUTSIDE OF THE WASHER. WHERE CAN I GET THAT. OH ONE MORE 4. IS THERE A WAY TO HAVE THE WASHER SERVICED SO I KNOW IT'S IN GOOD WORKING ORDER. LIKE A CAR TUNE UP? WHO DO I CALL? THANKS!


This is just to let you know that the internal water softener needs water-softener salt. If you do not use the softener (I do not at my house) then the light serves as a convenient on/off light.The other issues you have can ... Miele 24 in. Incognito G843SCVi Built-In Dishwasher

Dishwasher has always had a knocking noise, very annoying. Has nothing to do with dish placement. sounds like something is hitting the door. But I tied clothes around the racks and started it and it still knocked, so I don't think it is the racks hitting the doors.


CHECK THE SPRAY ARMS ROTATE FREELY AND ARE SECURE--DOESN'T WOBBLE TO HIT TRAYS-- DOES IT DO THE KNOCKING WHEN DRAINING OR JUST WASHING. ... GE 24 in. GSD2120C Built-in Dishwasher

My Asko D1606 doesn't seem to be filling/retaining enough water to pump actively through the swing arms. When I add a litre or so of water in manually and hold in the door catch, I can see it appear to start working properly. The tablet is still sitting on the bottom of the dishwasher after the cycle has ended and the dishes are still dirty. The pump sounds all right and it is emptying fine. Also, probably due to the lack of water, the cutlery basket has melted right through, and I am sure any p


Check to see it the dishwasher has been pushed back ever so slightly. The water coming into dishwashers and exiting are on timers and if the hose is pinched this can affect it. Your dishwasher may appear to be in the same place but just pull it forw ... Dishwashers

Double dash on display and when put in service/maintenance mode, all the lights came on and stayed on overnight. Still not working until I tested the door switch. It looks like poor engineering on the design. Plastic bar that depressed the door switch was not pushing all the way. It appears that the bar was bent to compensate for the too close tolerances and after the depressing of the switch for six years it did not reach anymore. So I got hair dryer, heated the plastic bar and bent it down to


... Kenmore 24 in. 15932 Built-in Dishwasher

I have a Frigidaire Dishwasher, model #FDB635rfs It is not that old, but appears to have quit working. It sounds like it runs the water gets pushed in by the tube on the side but goes straight to the bottom of the washer. It looks like the spray arms are not spinning. Water is not circulating. Element still heats up. Detergent just runs down the inside of the door and doesn't dissolve since water is not circulating through arms. I have just replaced the water inlet valve and it did not hel


Don't know about yours but many of the rotating spray-heads are turned only by waterpressure, not a separate motor.\015\012The rotator is normally pretty loose and should turn willingly by hand; if it seems stiff and your water pressure is normally l ... LG LDF6810 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0882 seconds