Having problems with your Bosch Dishwashers ?

Hello, I have a Bosch SGS43A42UK dishwasher with a problem in that the cycle does not seem to end - it seems like the dishwasher is still trying to remove water long after it has been extracted. I pressed both buttons together and the *End* light flashed and then the cycle ended. Help, please?


Answers :

Repair Help & Product Troubleshooting for Bosch Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hello, I have a Bosch SGS43A42UK dishwasher with a problem in that the cycle does not seem to end - it seems like the dishwasher is still trying to remove water long after it has been extracted. I pressed both buttons together and the *End* light flashed and then the cycle ended. Help, please?


... Bosch Dishwashers

When I press the start button, Bosch dishwasher (model SHY56A 05UC) just keep running the motor pumping the water out of dishwasher, irrespective of: 1) the wash cycle it is on, 2) whether the door is closed or open, 3) whether I cancel drain cycle, as told by Bosch Cust Svc in following steps: - "Cancel Drain" by pressing 'Quick Wash' and 'Regular Wash' buttons together for a minute until it shows 0* - Shut power off for a minute and wait for a minute - Restart on Quick Cycle. Paid


What is happenig i believe and has happened to me 2 times is that the water level float that is on the left side of dishwasher is stuck.\015\012\015\012Either remove side panel and flick lever or pull dishwasher out and tap lower portion ... Bosch SHY56A02 / SHY56A06 Built-in Dishwasher

I have a kenmore Ultra Wash Dishwasher, Model 15825691. We were recently hit by lighting. Once hit, the dishwasher started up. Since then, all cycles work, however, at the end of any cycle, the dishwasher continues to run and fill the bottom of the washer up to about two inches and then cuts off, so when we open the washer, there is approx 2 inches of water inside no matter what. I have pressed the "Cancel/Drain" button, in which drains the water after two minutes, but when that is finished, the


There must be a problem wit the fill valve. Check which valve the water enters. Check first the wiring to the valve of the water inlet or where the water comes out to fill the washer. Check for physical evidence of damage on the solenoid (or contr ... Kenmore 24 in. 16539 Built-in Dishwasher

Hi, My dishwasher end of cycle light flashes on when i press the power button. then when i release the on/off button to select the cycle the dishwasher powers off. Can you please help? Thanks Dermot


... Electrolux 18 in. ESL4114 Slim-Line Built-in Dishwasher

I am having problems getting dishwasher to restart after I interrupted a cycle. I have done the cancel cycle pressing Normal and Delicate together. The dishwasher emptied then showed a PF signal. Now is it showing a LE signal and all Front display lights are flashing.


You should be able to reset it by tripping the breaker and waiting about 10 minutes. Then reset the breaker. Best regards, --W/D-- ... LG LDF8812 Stainless Steel Built-in Dishwasher

I have a Whirpool DU1145XTPQA dishwasher... It has started "Not Draining the water" at the end of the cycle. Dishwasher is only 2-3 years old. I have completly disconnected it and have taken it to my garage so It could be tested in a more userfriendly envoronment... I have found no blockage of any line..... The screen in the dishwasher is completely cleen...yet , when you press drain, It drains at a very very slow rate. I have noticed a small 40 Watt pump (drain pump) that attaches to the mai


There is only one motor that drains the unit.it seems to me that the impellar wheel is not turning fast enough to do the job,you have eliminated all other possible cause with the exception of the main board.\015\012\015\012replace the dra ... Dishwashers

I have a Beko DE2431FW Dishwasher which has stopped working. I select a cycle and then press start, the green light starts to flash and the cycle begins to start but after about 30 seconds it stops and the red 'end' light comes on. this happens no matter what cycle I chose. Can anybody help me with this please?


... Dishwashers

Asko d3120 i hear the dishwasher running ( the cycle i s not running just the sound of it )and it wont shut off unless i unplug it i cleaned out all the water and the drain hose is clear i pressed the on/off button together with the cycle on button to no avail.


If what is mentioned is correct to me, the motor or pump is running at times and you can hear the humming when the machine is plugged on. Your resetting also does not help to get the machine to run the program. It seems to me that the error is in the ... Asko 24 in. D3120 Dishwasher

Kitchen Aid dishwasher Model# KUDP01FLSS. 2 problems #1 Won't run unless you press in on the door and hold it for a few minutes then it runs through cycle normally. Problem #2 It won't drain water out at the end of the cycle when I open the door there is water laying in the bottom of the tub. I have checked the drain hose for clogging and it appears normal. I am able to remove the hose from the disposal and suck the water out of the tub using a shop vac this indicates to me that the drain is ope


... Dishwashers

Bosch dishwasher SGS46E22. Making strange noise as soon as the appliance is switched on and cycle not progressing or progressing very, very slowly. Ran test cycle (held in Auto and Eco buttons together and pressed start) - E6 appeared in display. Suspect pump or motor problem - how do I tell which needs replacing? Thanks.


... Dishwashers

Our whirlpool ADP 6565 dishwasher stops very close to but short of the end of the cycle, with the on-button flashing. If we press that button for a few seconds, it starts again and completes the cycle. I have cleared the filter on the inlet hose because we use tank water which does have particles in it frm time to time, but this made no difference.


It appears that you have a timer malfunction. at the point that the timer stop, you need to listen closely to any sound from the timer. if no sounds emerges, repalce timer ... Whirlpool Dishwashers

Bosch dishwasher SHE44C02UC, serial # 13693156: Does not cycle. I turn off and drain by pressing "Regular Wash" and "Rinse and Hold" together (need several of these to completely drain), then rinse by starting cycle and repeating above sequence. Slight burning smell also - motor? Is there a way to initialize the sequence, and if there is, is it advisable, given the slight smell? Robert Langridge


Hi\015\012\015\012First, try to hear a hum like sound from the motor however, the burning smell indicates that the motor is unable to work. You can also check that the motor is work ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

We have a Nautilus dishwasher which we kept during our kitchen renovation. When the dishwasher was installed back in it was tested and all was okay. However when the guys left and we started the machine it was for 98 minutes as against the usual 90 minutes. We were happy with this but now we find that at the end of the full cycle it does not turn off and continually beeps. It will not turn off by pressing the off button and you have to open the door. When you start again it immediately starts wi


Hi\015\012\015\012To reset you can leave the unit unplugged for 1hr, then plug\015\012it back in, you can also reset the controls by pressing the AIR DRY/RINSE\015\012ONLY/HEAT DRY button for 15 seconds. If the issue returns then the circ ... Fisher and Paykel Dishwashers

Hi I have a problem with my dishwasher not emptying the water at the end of the cycle. I have to empty the water by pressing the start the button and this empties the water out.


... De Dietrich 24 in. DVI300X Built-In Dishwasher

Hi I have a bosch classix maxi been great for the last couple of years but it has failed for the first time yesterday. The dishwasher did not start it just kept making a groaning noise and would not start the wash cycle. I can press end a noise changes but the noise just keeps goin for hours if not manually stopped. Any suggestions?


Completely unplug the dishwasher and leave disconnected for at least 10 mins.\012\012Also be sure to check the drain pipe is not kinked or obstructed and that the filter is also clean and empty ... Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

I have a Siemens aquasensor aqua stop dishwasher. At the end of a cycle there is dirty water left at the bottom of the machine instead of draining away. I have checked the filters and all are clear. My daughter pressed a button the other day and then I turned it off - could this have caused the problem?


... Siemens Dishwashers

Miele Dishwasher Model G1040, Type HG03, NR: 32/65143704 The machine is three years old. The cycle reaches almost to the end, then all three LEDs merge together, and the pump runs continuously, even with the master switch off. I have taken the machine out and removed the base plate. When I first took the machine out of its position, I tipped it backwards and water came out of the bottom. All hoses and parts in the bottom section seem perfect in every way but the inside of the bottom plate indica


... Dishwashers

WATER DOES NOT COMPLETELY DRAIN FROM DISHWASHER. TOOK APART DRIN VALVE OTHER NIGHT AND PUT BACK TOGETHER AND IT STARTED WORKING FOR ABOUT 5 LOADS. NOW THERE IS ABOUT 1/2 INCH WATER STANDING IN BOTTOM THAT IS NOT NORMALLY THERE AT THE END OF THE CYCLES.


It is likely that the water pump is feeling its age. Replace the pump. ... GE 24 in. Profile PDW7800 Built-in Dishwasher

Hello, I have a Neff Dishwasher S5453X1GB/74 and it's not draining the water out at the end of the cycle. I have unscrewed the filter and released the impeller. I have also cleared the waste pipe that runs to the sink waste and put loads of cleaner in the dishwasher. The pipes seem to be clear as water goes somewhere during the cycle but backs up at the end. A few times when I started a cycle the water did not spray out but I could here the drainer or motor? running. I jetted water through th


... Neff 24 in. S5453X1 Built-in Dishwasher

Dear sir In an attempt to dislodge a blockage of my sewer line using Draino and a plunger some of the Drano ended up in the dishwasher and now the dishwasher will not run. My dishwasher is a SHU3036UC/U12. When starting the unit up it empties the unit but the cycle newer ends, in other words the timer does not advance to the next cycle, I have determined that the timer motor works by removing it from the unit and supplying it with power. One thought is, can the water level switch be stuck in


HiCheck this video and clean the drain pump assembly: ... Bosch SHU3036UC Dishwasher

GE PDW7300 dishwasher - must slam the door shut to get a light on the panel and when the START button is pressed, it looks like the dishwasher is cycling thru a wash, but there is no water. When I press the START cycle again, it seems like it thinks its pumping the water out for a few minutes, then the light will go off. If I start it again and push really hard against the door, I can hear the water go on. But if I stop pushing the door, the water stops. The dishwasher was installed in 2001, but


... GE 24 in. Profile PDW7300G Built-in Dishwasher

Our dishwasher is no longer cleaning dishes very well and usually the detergent tab that we put in does not dissolve completely. Our dishwasher is a General Electric Model # PDN7800G00WW and several years old. The water here is very hard. On a separate note and a new development is the control panel seems to be messing up. When we press the ''speed cycle'' which is normally 37 mins it goes to 86mins and lights up the ''speed cycle:'' button. pressing the ''glass cycle'' lights up the adjacent '


Hi,\015\012\015\012There are various reasons for the Dishwasher not cleanig the Dish properly, From your query we can understand that, it must be issue with the Dishwasher selecter switch..\015\012\015\012DISHWAHER SELEC ... GE 24 in. Profile PDW7800 Built-in Dishwasher

My SHE4402UC/36 dishwasher malfunctioned all the lights were flashing and the machine was trying to drain. The guy came out and replace the control board. The dishwasher now read 199 on all cycles except the rinse and hold, the santitized light does not come when its done. The repair guy told me the count down timers were flakey on the the Bosch dishwashers and it would learn my dishwashing patterns in time. So 6 cycles later the dishes are still damp at the end of the cycle-the length of the cy


Well its not baloney but it is cheesey. normally changing the module is the cure but it has to be programmed correctly. bosch has a recall so check it out and see because the recall is free and the tech is suppose to know how to program it. go to the ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

Frigidaire dishwasher won't end cycle - will run on and on for hours. Sometimes it cycles through, usually it just endlessly washes and rinses. I have to CANCEL the cycle, which causes the dishwasher to empty and run a few RINSE ONLY cycles (which are consistent, cycle time wise) to rinse the soap off of the dishes. Also, the door for the soap seems to stick - how long into the cycle before the soap door should open? Also, does opening the washer during it's cycle (to add more dishes) change or


I would say the resettable thermostat has failed. There is a thermostat which senses the water temperature, and when it fails, it causes the dishwasher to run constant. Replace the thermostat underneath the dishwasher and that should cure problem. P ... Frigidaire 24 in. FDBB540 Built-in Dishwasher

Omega Technowash Dishwasher. Model DW 2005 WH. The electro-mechanical timer stops just after the dishwasher powder is released and again near the end of the cycle. Also the water is not heated and no drying heat at the end of the cycle.


HiYou most likely have a fault with the Thermostat. That is common on Omega Technowash which is similar to a Smeg dishwasher. More often than not the Thermostat fails rather than the heat element. However, not to completely dismiss a fail ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2184 seconds