Having problems with your Bosch Dishwashers ?

I have a Bosh Logic dishwasher SGS65L12GB/04 The other day it got to 1 min left and would not stop pumping out water and continued even with the door open. After 5 mins playing around it started working again for a further 2 washes. Now when switched on the pump for pumping out the water works continuously. Reset it time seem to count down but does not do anything reset time goes to 0 and beeps but still the pump runs even with the door open. all buttons seem to work fine but no washing and pu


Answers :

Hi Jonathan,
\015\012
\015\012Welcome to FixYa.
\015\012
\015\012Your float may have got stuck or it's possible that you have water leaking into the bottom of the washer. In the bottom of the wash compartment, next to the drain you will find a plastic dome/mushroom (the float). You might need to rotate the bottom spray arm to see it.
\015\012
\015\012Turn the washer on so that the pump starts to run, open the door and push down on the float. This should stop the pump running. When you let go of the float, if it rises back up on its own, then it's almost certain that you have water in the bottom of the washer. If this is the case please post back for further assistance. If the float stays down, then it may have simply got stuck.
\015\012
\015\012Please try this simple test and post back with the results.
\015\012
\015\012Regards,
\015\012BElectric
Repair Help & Product Troubleshooting for Bosch Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Bosh Logic dishwasher SGS65L12GB/04 The other day it got to 1 min left and would not stop pumping out water and continued even with the door open. After 5 mins playing around it started working again for a further 2 washes. Now when switched on the pump for pumping out the water works continuously. Reset it time seem to count down but does not do anything reset time goes to 0 and beeps but still the pump runs even with the door open. all buttons seem to work fine but no washing and pu


Hi Jonathan,\015\012\015\012Welcome to FixYa.\015\012\015\012Your float may have got stuck or it's possible that you have water leaking into the bottom of the washer. In the bottom of the wash compartment, next to the drain yo ... Bosch Dishwashers

Hi. I have a Siemens SE65E331GB Built in Dishwasher with an aquastop system. The problem is that it seems to be stuck at the end of a cycle. The pump is constantly running when stitched on. I won't top after a reset and it continues to run even if you open the door. The water supply light also comes on indicating that there is no water getting to the machine. I have tried resetting the aquastop as per the advice in other threads. This has helped in that the water supply light now stays


... Siemens Dishwashers

Miele Diamante G 2150 SCU Dishwasher problem ----The program cycle indicators "Rinse", "Drying" and "End" flash at the same time. The drain pump is running when the door is open. I have reset the power and cleaned the drain pump and non return valve and Spun the propeller several times in both directions to check for obstructions. Still has the same problem. Water is being drained continuously even with power switch on dishwasher turned off.. Had to shut the breaker off to get it to stop. A


Hi\015\012\015\012Plugged system or a jammed drain pump can cause these issues, also make sure the drain hose is not blocked. Check the drain hose for any visible clogging, remove if present. If no visible lint is present then remo ... Dishwashers

Bosch Dishwasher model : SHV4313GB/17 The machine won't switch off and the pump is still trying to drain water ( there is no water left in machine ) The cycle seems to have finished as it has made the beep sound as if it has finished. The dishwasher is still working even when you open the main door. Have tried to reset it but to no avail. Even after turning it off at the mains it still starts up again as if in mid cycle ! HELP PLEASE


I have a SHV. My sink drain backed up, and the water accumulating in the sink then migrated to the dishwasher, through the drain pipe, causing the dishwasher to fill up and, it turned out, overflow a little. When I turned on the dishwasher, the wat ... Dishwashers

We have a neff dishwasher and the pump is draining all the time (even when the door is open) but there is no water in the dishwasher. Is there a way to stop the pump and reset the setting for the flood overflow


Hi there, our neff S54T09 doesn't seem to want to fill with water, it starts to fill for about 5 seconds then stops, then stops & starts filling for about 10 seconds then stops completely & nothing happens!! Have checked the water inlet & ... Neff 24 in. S5409X0 Built-in Dishwasher

[email protected] My problem: I have a GE Quietpower2 dishwasher. The normal wash and heated dry lights continiously blinks, the pump seems to be operating with no water present. I've tried turning the power off and using the reset button with no results. The lights blink even with the door open.


Hi,It sounds like the main control board has gone wacky....replace the control board.\012That is not that hard to fix and you can easily buy the partsyourself online...Here is a tip that will help you with the onli ... GE Dishwashers

My thermador dw44zs dishwasher: drain pump runs continuously when turned on even when the door is open. I can't seem to reset the cycle to allow for water to come into the dishwash


There are a few possibities...if you remove the lid and take the two t20 screw off the left side panel at the front you could check the pressure chamber and its hose are not blocked. Use the link and go to page 4, part 0426 and 0424. You can al ... Thermador DWU244 Dishwasher

Bosch Dishwasher SHV4313GB/17 Wont switch off ! The machine keeps running even when you open the door The pump is trying to drain water away (even though there is no water left in machine ) Have tried to reset it as instructed but to no avail. It has beeped like it has finished cycle but the pump wont switch off HELP PLEASE !


Introduction: This may work for your problem, but only if you're finding that you cannot get further water to flow into your machine. If your machine fills OK, then this ISN'T a solution to your problem. If your machine doesn't fill but your drain m ... Dishwashers

Full model number is SGS45E08GB/56 Will pump out water if you pour it in manually. Takes in water - sometimes. Main pump runs but no water flowing out of arms. Float switch is not operated and is not defective (tested off the machine). Intake solenoid valve seems to work properly (tested off the machine). Pump continues to run even if door is opened.


... Bosch 24 in. SGS45E02 / SGS45E08 Exxcel Free-standing Dishwasher

Good mroning after starting any program first the pump will run followed by water intake. After a while the machine stops and the light intake/drain starts blinking. Most of the time water will stay in the machine. After pressing the on/off bottom first switching the machine on again and starting a new program the machine pump start running emptying the water but than stops after a short water intake again. I opened the water stop but it seems to be ok. The filter inside the machine is cle


Good morning don't get shocked because ullu ki to abhi subah hi hui he ... Miele 24 in. G892SCU Plus Built-in Dishwasher

Dishwasher - Bosche - SHV43A03GB - When the main power switch is ON, even with the door open the pump/motor continues to run (ie. Stop-cycle does not operate). However, the wash-program itself does not run, even with the door closed (ie. No water entering the dishwasher, even though water supply is on and feed lines are clear - not kinked). It is like the program is 'stuck' and I cannot seem to get it to reset.


Your door switch is likely faulty and should be replaced. You can get them at partselect.com ... Dishwashers

Hi. I have a Siemens SL84A30 dishwasher. It runs to a point that the drain pump stays on and will not shut off even if you open the door. Even reset the power yet the unit still trys to drain with the door open. There is no water sitting in the machine..


Hi -\015\012\015\012\015\012The pump running continuously even with the door open means the anti-flood protection system has been activated. This is caused by one of the following:\015\012\015\012\015\012- Defective or stuck f ... Siemens 24 in. SL84A305UC Built-in Dishwasher

Dishwasher does not start it seems there's no water coming in the tub. I got a trouble shooting manual from ejunkie.com and tested the coil of the water valve which read 1000 Ohms, which means it's OK. Then I hot wired the coil while connected to the water line and the valve opened and I had water flowing [ in a bucket] I have tried to start the test program [hold power scrub plus and regular switch at same time then start button] and lights start flashing you hear drain pump come in then the un


... Bosch SHV4803 Dishwasher

MyTecnik dishwasher, TKD795/3 is draining out as soon as you switch on and continues doing this even with the door open. If you reset and try to start a new programme ot continues to drain and the water tap symbol comes on. I have disconneted to water supply and checked the little red filter and it was fine. The water pressure seem fine and not sure what to do now.


... Tecnik 18 in. TKD7000 Built-in Dishwasher

My maytag quiet series fills with water and then starts for 5 seconds then stops. This happens 4 times and then the entire system just stops. To help troubleshoot I used a screw driver to trigger the closed door so that I could leave the door open when the cycle starts and the pumps seems to be working and water sprays all over the place. I also took apart the impellar blade to make sure there was nothing jammed and everything is clean. Maytag MDB7500AWW


... Maytag 24 in. MDB7600A Jetclean® II Built-in Dishwasher

Have a Bosch shy56a05uc dishwasher that suddenly stopped working to a point. I believe it is related to the door latch switch, because I don't feel the door securely latch shut when I close it, and I also don't get any cycle lights or times registered on the LED readout. If I depress the on switch, the drain pump will start even with the door open, and, depending on how long I leave the switch on, water will start to fill in the dishwasher, open or not.


Does your dishwasher electronic control or mechanical timer? if mechanical timer, I encounter a similar problem n change the mechanical timer. that problem solved.\015\012\015\012Prince P ... Dishwashers

Dishwasher malfunction MOST OF THE TIME it shuts itself down before fully filling with water - SOMETIMES it doesn't shut down until the minute the wash pump starts - SOMETIMES it washes for 10 or 20 minutes before shutting down - SOMETIMES it will even run a whole cycle, BUT it doesn't open the soap dispenser door - tried doing a diagnostic run but after it turned on all the lights on the panel it started to fill with water and shut itself down......... HELP


Follow this steps and fix it. God bless youFloat Switch\012\012\012The float switch may be hung up and this can cause the dishwasher to be stuck in a cycle. Check the ... Dishwashers

I have a GE Quiet Power 3 dishwasher that was working fine last week. Over the weekend I ran it and we could hear a banging noise, so my boyfriend opened it three or four times in a row (during the cycle) to figure out what it was. The fourth time, it went dead. I checked and it had tripped the breaker. I reset the breaker and the dishwasher seemed to be working again, however the lights on the front were flashing (they hadn't previously), and now it will run for about 10 minutes but no water ru


Were you able to figure this out? We have the same problem here! ... Maytag Dishwasher

Hi I have a Troy-Bilt Pressure washer 2200 psi model 20292. I've used it only 4 or 5 times. It ran great for an hour today then it lost pressure. Seems like the pump is not working. The engine runs fine but no pressure. The water runs through the nozzel and I blew air in the lines to make sure there is no blockage and found no blockage even in the pump lines. Any ideas. Tom


... Briggs & Stratton Gas Pressure Washer 20244

Tecnik DW2677 Hi, my dishwasher regularly starts to bleep after starting a wash program. When the door is opened it stops bleeping and the right hand light flashes 7 times repeatedly in sequence. By holding down the start and program change buttons together for a few seconds, it will reset. If you then close the door all is well for a few seconds the pump sound like it expells some water and then it starts to bleep again. The above process can happen several times before it decides to do what it


Check your water intake- i had the same issue - a leaky fitting wasn't supplying enough water to the dishwasher. had exactly the same symptoms you describe. fixed the leak, reset the dishwasher & it's working fine.\015\012\015\012\015\012\0 ... Tecnik TDW2677 Built-in Dishwasher

I have a Bosch SHU43C05UC diswasher. Last night, I put it on before going to bed as usual. I was awakened a couple of hours later to a loud grinding sound (like a pump being run dry), and found the noise coming from the dishwasher. The display read "0" time remaining, so I opened the door and the dishes seemed clean, so I left it shut off. Tonight I have been trying to troubleshoot the problem. The dishwasher will turn on, but it will not seem to fill with water. I have verified that the


Ok well before you can do anything you must obtain a service manual, link below.\015\012\015\012http://allrepairmanuals.com/bosch ... Dishwashers

Bosch SHU4302 WITH REPAIRED PC BOARD has been working fine for several years now seems stuck in rinse/drain mode and is not quite pumping cabinet dry. I have removed the screens and located the small impeller at bottom below cover. The impeller rotates as though it has multiple spring loaded stop positions. When I turn on the unit and open the door water is trickling from the sprayer arms at low pressure. It seems stuck in rinse mode and will not advance cycles or reset when shut off.


... Bosch Dishwashers

Noticed dishes on top shelf not entirely clean. Ran machine empty and opened many times during wash. Noticed that Lower Spray Arm works as expected, but Middle Spray Arm turns only 1/8 or less, then Lower Arm spins again. Schematic with Use and Care manual just says pump motor switches from one to the other in certain cycles, but I don't see this happening. Looked for obstructions to water flow and pressure seems normal. Is control for this function part of the pump, or in the control panel?


Something could be in that checkball, see page 5 ... Frigidaire 24 in. GLDB653A Built-in Dishwasher

Hi. Our DS603I dishwasher starts on the Rinse cycle on its own - it beeps, red light flashing and no water entering the tub. It does this even if it is open. Similarly, when we try to turn it on to do a normal or heavy cycle, it starts (making quiet a loud noise) and then goes to the Rinse cycle, beeping, red light flashing, no water going into the tub. The pump wheel is turning. We can't find any blockages in the tubes. We have power-cycled it many times. Please help!


Dishwasher Repair Guide: How To Fix a Dishwasher - ACME HOW TO.com\015\012\015\012\015\012\015\012 ... Fisher DS603W / DS603B / DS603I Dishwasher

My Frigidaire Model FDB2810LDC1 dishwasher will not stop running. Seems to complete a normal cycle and different cycles can be selected with normal time countdown but at end only rinse agent low light remains lit and sounds as if pump is still running. If opened, water appears to be streaming from rotator arms. Have cycled power but symptoms remain.


... Frigidaire Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1364 seconds