Having problems with your Bosch Dishwashers ?

THe PUMP IS CONTNIOUSLY ON. i NEED TO RESET THE SENSOR FOR THE PUMP BUT WHERE IS THIS SENSOR RESET??


Answers :

Repair Help & Product Troubleshooting for Bosch Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

THe PUMP IS CONTNIOUSLY ON. i NEED TO RESET THE SENSOR FOR THE PUMP BUT WHERE IS THIS SENSOR RESET??


... Bosch Dishwashers

Hi our nemo dishwasher starts a cycle and fills but does not start cleaning cycle. Light under start button flashes. If start button is held on it resets and pumps out. We live in an area with high clacium in water. At first the machine only pumped out and did not start filling. I have cleaned the level sensor ( membrane switch filled with calcium) and it at least stopped pumping and started to fill. It does not proceed from here. I checked the level switch it seems to be working OK (NO and NC c


Hi.You need to move the appliance and check the height of the drain hose. If there is water in the tub you may have a syphoning problem (water refluxing in the tub) because of incorrect height of the drain hose elbow.The led t ... Fisher and Paykel Dishwashers

On my bosch shu66 diswasher the error code indicates a number 1, aqua sensor I think. There is a screw missing in the soap dispensor and it's been letting water into the door interior. could this be repaired by replacement of the screw and drying out the interior insulation and wiring The solution I tried didn't clear the error code on the panel. Is there a reset or do I need to replace the aqua sensor or ? The machine still won't start and displays a #1 on display. There is no water in the whi


... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

Starts cycle, drains ok, then "intake/drain" LED comes on solid for 4 seconds, flashes 4 times, solid 4 seconds, flashes, etc. no water coming into dishwasher. DOUBLE CHECKED the intake filter its all OK ! how do i 'reset' the machine? Im pretty sure the sensor is goofed up and needs to be reset but i have tried holding various buttons, start, power etc, cannot figure out how to do it


... Miele G2430SC Dishwasher

Electrolux Dishwasher DX403SJ - 30 Overfill fault but unit is dry. Overflow sensor intact and all looks good. Think we need a reset code. Can anyone help?


... Dishwashers

Bfd46w dishwasher my dishwasher keeps pumping but there is no water is coming in is this something to do with the overflow sensor can it be reset or is it broken


... Baumatic 18 in. BFD46 Free-standing Dishwasher

Dishwasher problem Hi We have a Whirlpool GU 2300, the machine has stopped and is the clean LED on the control panel is showing a 7 pulse sequence which I guess is a fault alarm. I have tried resetting, checked the door switch and looked at the pressure sensor at the drain pump outlet. I changed the heating element and fitted an uprated control card earlier this year. Any ideas?


I solved the reset by pressing the air dry and reset buttons 6 times in sequence, the whole panel array lit and I was then able to reset. I have had no problems since and have used it 6 times. I initially thought that the chipset had a volatile memor ... Dishwashers

My DPD 3100 is leaking from a brass fitting on the side of the pump (opposite of the white ??reset?? button. The brass fitting has a star shaped whole in the center. When i remove the fitting, there's a heavy duty spring behind it. Do i need to replace the fitting, or is there another problem? Where do i find parts for this?


First things first, before replacing I would wrap this valve with teflon tape and then retighten and see if the leak stops, I checked the entire schematic and found no listing for a spring so this is part of a valve assembly of some type. It might b ... Dewalt DPD3100 Gas Pressure Washer

Kenmore model 665.15829 Air dry lock button light is on. Washer won't start. tried different codes to reset. no luck. when I pushpots pans button and start it goes into sensor mode and tries to pump out. after one minute operation it stops. The tub is dry no water in unit.


I have reviewed your problem and have the fallowing for you to aces.\015\012First, believe it or not, in some cases, when you get a power urge the unit will lock out and continue until a full reset is completed.\015\012Try di ... Dishwashers

LPR600 Prima Dishwasher When starting washer the pump sounds to be working then the light flashes a sequence of 6 beeps. I have tried resetting by depressing the start button but cannot clear the fault. My original thought was the temp sensor but not sure.


... Dishwashers

DU1055XTPQ3 built in Dishwasher... panel has power "cancel" button when pushed you can hear the pump running but on wash the light blinks about 3 times and goes out, nothing happens. Is there a sensor or something in the panel that needs replaced? Jim


Hi\015\012\015\012First try resetting the dishwasher by pressing the AIR DRY button and hold it for 15 seconds. After this if it blinks again 3 times then the control needs replacement. Hope this helps...please post back for further assistance. ... Whirlpool Dishwashers

Viking professional dishwasher DFUD142 panel lights flashing, and cannot turn of pump, need to cut power, will not go on? worked perfectly 4 yrs. what to do? repair man did not fix.


... Viking DFUD142 Built-in Dishwasher

I have a Bosh Logic dishwasher SGS65L12GB/04 The other day it got to 1 min left and would not stop pumping out water and continued even with the door open. After 5 mins playing around it started working again for a further 2 washes. Now when switched on the pump for pumping out the water works continuously. Reset it time seem to count down but does not do anything reset time goes to 0 and beeps but still the pump runs even with the door open. all buttons seem to work fine but no washing and pu


Hi Jonathan,\015\012\015\012Welcome to FixYa.\015\012\015\012Your float may have got stuck or it's possible that you have water leaking into the bottom of the washer. In the bottom of the wash compartment, next to the drain yo ... Bosch Dishwashers

My bosch dishwasher sgs09a15 is leaking on or from the pump assembly can i repair the pump or do i need to replace the pump motor assembly completely en which do i need


I consulted another website ... Bosch Dishwashers

Dishwasher front panel lights are all blinking in unison. Pump has removed all water from bottom including sump. Pump and lights will not shut off or reset with dishwasher door closed or OPEN. I have shut the circuit breaker off to keep from burning up the pump. Problem continues if I reset circuit breaker.


It would help to know what the make and model of the dishwasher is.\015\012\015\012Most likely the flood switch at the base has been activated. ... Dishwashers

Honda Trash Pump Model WT30X Stalling - 8hp engine runs for approx 5 seconds that shuts down, restarts after I hear a relay click ? oil is fine - so I do not believe that it is an oil pressure sensor. Are there any other sensors ? Does water have to be pumping through it??


Their is an oil level sensor that lasts around 3 months of use. unplugging it would solve your problem But replacing it is a night mare. and if your oil runs out It's all over. if not the oil sensor, and your spark is constant Check your fuel system ... Honda 8 HP Engine

Maytag Dishwasher I need the reset sequence for my dishwasher. The power comany had turned off the electric to the house to make chages elsewhere in my house. When the electric was turned back on all appliance came back on except the dishwasher. The dishwasher has a front panel touch pad and three of the panel lights are flashing. I know there has to be a sequence to reset the machine. I also need the peace and quiet in the house since I am the husband and am suppose to know it al


We have a model mdvtt53aww1 and you can push three buttons and will light up the hi temp wash, heated dry and sanitize is there a code make it start ... Dishwashers

I have a G 2400 HH-R and I need to replace the pump oil, I know I need Karcher Pump Oil 6.288-050.0 but I don't know HOW to drain and replace the oil. Thanks, Bill


... Honda Karcher G2400HH-R Pressure Washer

Dishwasher has stopped partway through cycle, not pumped out


Not a moisture sensor, a water depth sensor to gauge fill level.  Not the problem here.  There is a solenoid valve under the machine.  It routes the water either to the wash arms or to the drain.  It is likely  jammed so that ... Whirlpool 24 in. ADP5966 Free-standing Dishwasher

Noisey pump a rattling noise is heard during drainage when the pump is running and all water is not pumped out of tub. A second cancel/drain cycle seems to empty the tub, but pump makes the same rattling noise. Do I need a new pump?


Take the drain pump apart and look for debris, or broken pump impeller. Remove the lower spray arm and filter assembly, check for debris in the sump and check the drain check vavle to make sure it is sealing properly. While in there make sure the foo ... Whirlpool 24 in. GU1500XTLS Stainless Steel Built-in Dishwasher

Wash pump motor removal to clear wash pump of a large object.we have washer out of cabinet on it back on the floor. Need to remove wash pump motor to access wash pump to clear a large object from the pump rotors.


... Whirlpool GU2300XTS 24 in Builtin Dishwasher

I have a bosch dishwasher model she46c. the float stuck and the pump ran and almost burned out smelled burnt. got washer to restart everything works but pump is noisy. replaced pump but it is still noisy. What do I need to check? nothing is stuck in pump. thanks ron


... Dishwashers

My Troy Bilt power washer (using Honda GCV160 engine) has no pressure coming from the pump. I checked the water flow, everything seems fine. I believe the pump needs oil added, however, I can't seem to firgure it out (how to add oil to the pump). I did notice that previously, I used to see drops of oil coming from under the pump. I I have a bad seal, can I add oil and test the pressure before I change the seal? Please advise.


I had a similar problem. Turns out I had left the hose disconnected and some sort of wasp built a paper type nest inside the washer tube that the hose connects to. I had to take the pump off and take apart and then cleaned it out with a screw driver. ... Honda Black Max 2600 PSI Pressure Washer

The unit fills up with water but the circulation pump wont turn on. if i jump the pump it works. the pump is connected to the timer board. is there any sensor that would cuase the timer board not to turn on the circulation pump. this unit seems to be manufactured by ASKO mod. DW20.3 i dont want to replace the board ($375.00) if not nessary. thank you


Hi\015\012\015\012\015\012Thanks for using FixYa. There is no sensor on your dishwasher for drainage purpose however, it uses a drain solenoid to open and close the dishwasher drain port. If this \015\012solenoid ... Dishwashers

Have GE Dishwasher model GLD6700N20WW,unit has stopped draining! Took apart and pump was running when check, but no water coming out. Checked drain line and pulled apart pump housing, all clear. Thought maybe pump has a silinoid built inside of it and was stuck shut, so bought new pump and same thing, no water will go thru! Please help me? Is it control module, or turbitity sensor possibly?


... GE Profile PDW8600J Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1099 seconds