Having problems with your Bosch Dishwashers ?

Bosch dishwasher SHU3032 UC/14. The soap dispenser does not open. In the past I've used dishwasher magic or similar to clean the dishwasher of hardwater deposits and that solved the problem. The cover opens and closes manually. The springs seem fine. I removed the door skin and the linkages look good. I checked the resistance on the Wax motor and it is with in spec, approximately 2150ohms. I 've watched the cycle and the wax motor never seems to actuate. I put my meter on th


Answers :

Repair Help & Product Troubleshooting for Bosch Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bosch dishwasher SHU3032 UC/14. The soap dispenser does not open. In the past I've used dishwasher magic or similar to clean the dishwasher of hardwater deposits and that solved the problem. The cover opens and closes manually. The springs seem fine. I removed the door skin and the linkages look good. I checked the resistance on the Wax motor and it is with in spec, approximately 2150ohms. I 've watched the cycle and the wax motor never seems to actuate. I put my meter on th


... Bosch Dishwashers

I'm trying to fix a whirlpool du980qpdq6 dishwasher. The door on the soap dispenser won't open. I've checked the latch and it works...no blockage. I've taken the door apart and looked at the Wax motor in the door. Apparently that is what actuates the mechanism that opens the door. Does anyone know how to test the wax motor to see if it is functioning?


... Dishwashers

Water leak have the Ge triton dishwasher (Model # GSD5320D02BB, bought it n 2001) and currently have very small amount of water leaking out of the door during a run cycle. I did check levels when running and that seems to be fine......meaning the dishwasher is level and not an over-flow problem. My next thought is maybe it is a faulty door gasket. So my question is, where is the door gasket located and how do I replace it? (and where do I order this part from?). Looked for diagrams to follow and


They are in the bottom left and right of the door opening. GE likes to use L-shaped, molded and ribbed seals on most of their models - hopefully also on yours. Typically these can be removed by hand and easily replaced without taking anything apart. ... GE Tritonr XL GSD6260JCC Dishwasher

I have a General Electric Potscrubber dishwasher. When the cycle is finished, the water does not drain into the sink.I turned the unit upside down to look into the bottom. The motor turns freely. The instruction sheet I found in the bottom of the unit said to remove the filter screen and check the piston valve. I looked at what I thought was the piston valve, but I'm not sure how to check it. The line to the sink seems to be clear. The model of my unit is GSC3230Z03WW. The serial number is AZ627


... GE Dishwashers

My wife opened door during cycle. When she closed door it would no longer run. Looking at problems and recomendations on similar models, I replaced the board. Did not fix the problem. I have checked the fuse and the door switches for continuity and all seem ok. The only lights on the panel that come on are: under cycle- Pots & Pans, Light. Under Options - Heated dry. No other lights work and the dishwasher does not operate.


Hi,\015\012\015\012First off, sorry to hear that you replaced the control board for nothing..in hindsight. So if I understand what you're saying is this, You cannot select any cycles and the unit won't start...because the start button is ... Dishwashers

Smeg dishwasher model dw1612c type 12043 seems to be stuck. program lights 4 & 5 are lit up solid and theres also a beep beep audio warning.it will not reset this is with the door open wen you close door the pump goes on and off / on and off have checked all pumps pipes and motor there are no blockages and everything is turning freely. can it be fixed. ?


... Smeg DWD612C Built-in Dishwasher

The dishwasher stop during the wash cycle. It did finish draining the water from the tub. The machine is not showing a power signs, I check the circuit breaker and the fuse is not tripped. I open and closed the door and the door latch seems to be working fine. There is just no power to the washer. Usually when a machine breaks down, there still is power or buttons that light up on the front of the machine. I looked on the internet and many say that the fuse could be tripped. No where can I find


... Whirlpool DU912 Dishwasher

Hello, I have a Kitchen Aid (model # KUDMO1T JWHO) dishwasher that runs the motor in all cycles, with water fill & drain working fine, but the pump is not pumping water during any cycle, as the spinners and the inside of the washer are dry when I open the door, except for the water sitting in the bottom. Also, no normal swishing sound of water when the motor runs in any cycle. Looks to me like a mechanical break in the pump drive. How do I check the pump drive on this model? Do you have any


... KitchenAid Dishwashers

Whirlpool Dishwasher detergent door not operating properly. Main wash door opens immediately after starting dishwasher. No pre wash cycle. Loud humming noise coming from bi-metal switch or wax motor attached to the detergent cup assembly. I just replaced detergent cup assembly including the wax motor and I still get a loud vibrating humm from the actuator. model number du1055xtp3


Pdemaio,ngafm at your serviceI believe the loud humming you describe is an electronic problem. And is not worth changing parts randomly and spending unnecessary funds in this fashion!my advice is a hands on experi ... Whirlpool Dishwashers

About a 3 year old maytag stainless steel inside dishwasher, not cleaning, often soap resdue on dishes or silverware, I use fresh new cascade, checked to see if washer fills with hot water, seems to up to the bottom of the door when I open durning cycle, arms go around, no obvious plugging of the screens, no junk in the foot chopper propeller, no paper or plastic or food in the jets of the arms. Motor went out on it 9 month ago and I had it replaced by appliance repair station here in Missoul


Water must be 130 Deg F to wash properly. ... Maytag Dishwashers

Our dishwasher doesnt seem to be cleaaning the dishes properly. After the cycle soap residue remains on the door and bottom of the unit and the dishes are not getting clean. I have checked the supply line and discharge for blokage but both are clear. what should I be looking for?


Hi, \012I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in minutes...now the thing works li ... LG 24 in. LDF 7811 Stainless Steel Built-in Dishwasher

FDW60 dishwasher Hi My dishwasher is about 15 months old and the problem I have is that it seems to stay on pump and the Ecco45 light is flashing.  A repair company looked at the machine and said that the motor looked like it was leaking and water was getting in the bottom setting off the micro-switch.  He contacted Hotpoint who fitted a new motor today at a cost of £89.85.  Went to use dishwasher tonight and we still have the same problem.  The dishwasher started the washing programme for about


I've just (as of 10 minutes ago) had the same problem. I followed the advice given elsewhere in this forum and removed the bottom cover - water running out so needed a big towel to mop it up. I stood the machine upright and restarted it - no problem! ... Hotpoint 24 in. FDW60 Free-standing Dishwasher

My Hotpoint diswasher suddenly stopped working last night. It seems like it has no power to it, as the motor or pump does not seem to come on at all. Obviously when I get home from work, I will check the obvious first - making sure it has power to it, connections are secure etc. (I had a wire break before) If it does have power, I would assume checking the door switch and timer is next. Any suggestions, and any suggestions for checking the door switch and timer??


Sounds like your on the right track. I would use an ohmeter to check the resistance of the door switch by placing the meter probes on each side of the switch. Test while opened and closed position. Same with timer ... Hotpoint Dishwashers

I have a Bosch SHU8805UC/14 dishwasher. I took the front door panel off to install it better but ended up with two extra pieces that look like either part 935400 Door Guard, or 935526 Support. I cannot seem to find any place on the inside of the door where these pieces would fit. The dishwasher works fine but seems like it got noisier after I put it back together without these two parts. Can you help me locate the proper place for these 2 plastic parts?


Hello, \015\012\015\012Welcome to FixYa.\015\012\015\012I believe the parts you are referring to are likely the blocks in each corner of the outer door panel. These have been a sticking point for many I tech over ... Bosch Dishwashers

Dishwasher model: se6 tie1 Fitted under kitchen work-top. Problem: After setting a program & switching on & closing door ? there is a normal sound from within but if door is opened there is no evidence of water being pumped in. I previously cleared food debris from the drainage pump area (including under the pump cover), checked the spray arms and checked the water supply was getting as far as the long in-take pipe. As it seems problematic to remove the (screwed in) dishwasher, I have not che


... Dishwashers

I own a KUDS01FLSS3 KitchenAid dishwasher. The lights on the control panel do not come on and a cycle can not be started. There is about an inch of water in the bottom of the dishwasher basin and it looks like the previous cycle did not complete. I have checked the wall outlet that the washer is plugged into and the washer is receiving power from the wall. And ideas? My next thought was to take the door off and check the power supply running to the door panel and control panel.


Servtek06 writes:\015\012check connections @ control board/module. May be Control Board/Module. ... KitchenAid 24 in. KUDI01FLSS Stainless Steel Built-in Dishwasher

GE PDW7300 dishwasher - must slam the door shut to get a light on the panel and when the START button is pressed, it looks like the dishwasher is cycling thru a wash, but there is no water. When I press the START cycle again, it seems like it thinks its pumping the water out for a few minutes, then the light will go off. If I start it again and push really hard against the door, I can hear the water go on. But if I stop pushing the door, the water stops. The dishwasher was installed in 2001, but


... GE 24 in. Profile PDW7300G Built-in Dishwasher

Hello! I have a Kenmore Dishwasher Model # 665.15805890. The dishwasher came with the house and I'm guessing it is around 10 years old. My toddler was having a great time flipping the door to the soap dispenser back and forth until he pulled the door off of the pin. Now, I can't seem to position the spring in a way so that the door will spring back. I never looked closely at the hinge before, so I don't know if that is the only reason the door will not release the detergent, or if something


Hi.Please see if the diagram here can help you. Check if the spring is that indicated with nr ten in diagram. ... Kenmore Dishwashers

I have the E3 error on my Smeg DWI614 dishwasher which would indicate a heater error, however it is heating the water in the bottom of the machine but it seems to time out. The main issue seems to be that the recirc. pump is not running during the heating phase. I have taken the pump out, checked the connections etc. twice now and everything seems fine (the motor runs when tested). When I have done this (both times) the dishwasher has started again and run for 20+ cycles fine, then the issue com


... Smeg DWI614 Built-in Dishwasher

Hello, My GE dishwasher stopped draining. Model Number: VSD2304JOOWW I emptied out the dishwasher of the liquid, removed the cover and checked the filter. (Didn't look bad.) Checked the drain pipe under the sink and there was a little debris (slime) but very minimal. The garbage disposal was installed at the same time as the dishwasher 3 years ago (brand new place). What else could it be? Any advice would be helpful as my new home seems to be falling apart and it is getting pretty e


Drain pump either disconnected or jambed ... GE Profile PDW8400J Built-in Dishwasher

Ge model # gsc3200j01ww dishwasher. when the door latch is closed, nothing happens. motor does not start. if the timer is advanced to the next part of the cycle, water will spray into unit until float valve is triggered. water will not pump out, motor does not start. bailed out water, checked for stuck float valve-ok. removed drain screens and filters, cleaned. no motor, drain, or start. what parts should i check? always rinsed dishes before putting in washer. unit is portable or undercounter


... GE 25 in. GSC3200J Built-in Dishwasher

DISHWASHER I have a problem with my CDA - CW494 dishwasher (6 ½ years old) You can switch it on and the lights come on. Then when you go to shut the door the lights switch off and the dishwasher doesn't start. If you move the door up and down the lights switch on and off. My husband has checked all wiring connections and they seem fine.


One of the switches in the door latch are not making contact properly. before you take the door apart make sure the dishwasher is 100% level. this can affect the door lat switches ... Whirlpool 24 in. DU1100XTP Built-in Dishwasher

Working on a Whirlpool dishwasher DU915PWSS0 - The soap dispenser won't open automatically. We have replace the wax motor and have installed a new control board. When you pull up on the draw bar manually the dispenser door opens perfectly. I don't have a schematic and I don't have the test sequence so I can't run the diagnostic test. It's a blind assy process so you can't really tell if you have the draw bar over the wax motor and coupled. I need the schematic and or test sequence for the E


Please confirm if this is the model you have.\015\012\015\012I might have some access to th ... Dishwashers

Dishwasher The dishwasher detergent door opens during cycle but powdered soap remains in tray. At end of cycle glasses and dishes are wet. a little water is left undrained at bottom. This is a Frigidaire model FDB510LCS1. Checked upper and lower spray arms and they seem ok and pump seems to be working


I have seen this problem before on a couple of dishwashers.\015\012\015\012How are the dishes doing? Are they coming out clean, or do some of them "fail". \015\012\015\012If you rinse the dishes before putting them in the di ... Dishwashers

The dishwasher doesn't seem to have nearly enough water in it. The upper sprayer arm doesn't seem to be spinning when running (I open the door and look really quick) and the lower one looks like it barely spins and barely sprays water. The dishes are barely wet and the soap is just laying on the bottom. The water is on, there are no kinks in the supply line. It sounds like it is running, and pumps pumping, but being brand new I am not sure what it should sound like. It certainly doesn't sound li


I would lift the drain pipe higher. approx. 1/2 the height of the dishwasher . also rechack incomming water supply. Make sure no blockages and the like. Try again. ... Bosch Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.2728 seconds