Having problems with your Bosch Dishwashers ?

SHU 531 5UC/U11 Dishwasher goes to 2H Delayed start and also will continue to run at the 1 minute left mark. We replaced the circuit board within the last 2 years.


Answers :

Repair Help & Product Troubleshooting for Bosch Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

SHU 531 5UC/U11 Dishwasher goes to 2H Delayed start and also will continue to run at the 1 minute left mark. We replaced the circuit board within the last 2 years.


... Bosch Dishwashers

We have a n eight year old fully integrated asko dishwasher. Only the rinse cycle works, so I rinse many times - last rinse with detergent and then run the short program which does not wash, but will dry the dishes. The circuit board was replaced once before under warranty($500.00 labour) and I suspect that we may have to do the same again. Can we find this on the internet and do it ourselves; we have good electrical knowledge. Thank you in advance.


This is most likely an issue with the timer. Timers\015\012don't often fail. But if every other part of the dishwasher seems to be\015\012working properly and the timer knob seems to be stuck in one\015\012place--doing one function continuously--the ... Asko Dishwashers

I have a Bosch Dishwasher SHU5302. A year ago it just kept on running. I ran a diagnostic test and replaced the circuit board that had a burn spot. The unit washed after that but would not drain wa


... Dishwashers

I have the above dishwasher shv57c03uc just less than 5 years old. The door latch does not engage solidly. when i pust start button left side lights on indicator right does not come on and i have to push on button twice for washer to come on. When it does come on the cycle is real short and it does not complete a full cycle. I an asuming the circuit board is defective!! does this sound right? if so how can i replace the board?where can i get troubleshoooting instructions?


Hi\015\012\015\012You are right it is the ... Bosch 24 in. SHV57C03UC Built-in Dishwasher

Our Maytag MDBH985AWSO dishwasher is 2 years old, and the start button will not work. It just started up on its own and ran an empty cycle 48 hours after our last attempt to get it running. All other buttons appear to be working. Should we replace the control board its like 200$ for the part alone.


... Maytag MDBH985AWW 24 in. Built-in Dishwasher

I HAVE A 8 YEAR OLD KENMORE ELITE (WHIRLPOOL) DISHWASHER . THE THERMAL FUSE BLEW AND I REPLACED IT AND THE MAIN CIRCUIT BOARD. NOW THE UNIT APPEARS STUCK IN CANCEL 2 MINUTE CANCEL/ DRAIN/MODE AND THE RELAY CLICKS ON AND OFF TO THE DRAIN MOTOR. I HAVE BENCH TESTED THE DRAIN MOTOR AND IT WORKS FINE WHEN IPT 120VOLTS DIRECT TO IT ANY SUGGESTIONS . WHAT AMPERAGE SHOUD DRAIN MOTOR DRAW?


Hi\015\012\015\012\015\012The drain motor is of 120 V, 50-60Hz and 0.6 amp rating. Dishwasher not draining issue usually occurs due to kinked drain pipe, clogged drain filter or drain pump. Check the drain hose for any visibl ... Whirlpool Dishwashers

Unable to start dishwasher, only functioning light on the panel is the cancel/drain light. push that button the machine funtions for a minute or two and shuts off,also the light above normal wash is blinking. When the machine last functioned it would start with a very high decibel level.If its the circuit board I need an approximate replacement cost. Bob


If you go to searspartsdirect.com you can get the exact cost of the module. ... Dishwashers

I have a Briggs & Stratton Pro 3400 pressure washer that I got new last year and used for maybe 5 hours and it worked great. Have had it stored since then with stabilizer in the gas (I didn't run it dry) and now it won't run for more than a minute or two without dying. A dealer said it was probably bad gas and I now know that even with the stabilizer I should have run it dry last year before storing. Everything is like brand-new including plug and air filter so it must be the gas/carberator gunk


... Briggs & Stratton Prosumer 20324 Gas Pressure Washer

My G865 Miele dishwasher goes partway through the cycle then gets hung up and runs without advancing. We left it running when we left for vacation and it was still running when we came back. I'm assuming it is the timer mechanism. The dishwasher is ten years old but has been run only every other day or so. Is it worth fixing or is it better to replace?


It will cost alot to get repaired,10 years old you got money out of this one. ... Miele 24 in. G865 Built-in Dishwasher

The dishwasher cycle starts and gets 20-30 minutes in and then stops giving me the - - - like the door was opened, but it was not. If I use extra heated wash, the cycle stops at 63 minutes left. If I use the regular wash cycle, it stops at 43 minutes left. I have to click the resume button to get the dishwasher to complete the wash cycle. This has been happening evey time I use the dishwasher the last 2 weeks. It is Whirlpool dishwasher model GU2700XTSS! and is only 3.5 years old.


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I suspect based on your description...\015\012\015\012"stops giving me the - - - like the door was opened, but it was not, I have to click the res ... Whirlpool Dishwashers

PLD2560LCC1 Frigidaire Dishwasher...Control Panel shows 65 minutes left on lower rack, works for about 1 minute, shuts down. None of the buttons work. I changed the control (major circuit) board, same problem. I wonder if it's the control "panel"? I took that off and looked at it. Seems okay, but could the problem. I've heard this model has control problems, but I'm not sure if they mean the major control board or the control panel that has the buttons.


... Frigidaire 24 in. PLD2560LCC Energy Star® Built-in Dishwasher

SHU 5316 UC dishwasher by bosch. I think it is from about 1998 or 99. It blew a circuit breaker yesterday. I reset the circuit braker, but it won't even power on. It may have burned something out. We replaced the control board 2 years ago. Please tell us: 1. Is it worth fixing again, or just replace? 2. Any suggestios? Maybe the pump has shorted? THANKS SO MUCH!! Mark


Hi Mark -There's no internal fuse in this dishwasher, so if there's no power you may well be looking at a new control unit and probably another major component as well, depending on what caused the overload or short. The most likely ... Bosch SHU5316UC Dishwasher

Pld2560lcc1 Dishwasher...Control Panel shows 65 minutes left on lower rack, works for about 1 minute, shuts down. None of the buttons work. I changed the control (major circuit) board, same problem. I wonder if it's the control "panel"? I took that off and looked at it. Seems okay, but could the problem. I've heard this model has control problems, but I'm not sure if they mean the major control board or the control panel that has the buttons.


Pulled the touch pad, go after the middle third with a very small screw driver, cleaned the flex circut with contact cleaner\015\012\015\012powered up fine seems to be working again ... Frigidaire 24 in. PLD2560LCC Energy Star® Built-in Dishwasher

Dishwasher starts and runs to 2nd rinse cycle, when pump starts to pump water out, all lights on front display flash along with key pab lights blinking. you can turn off and restart, but is does the same. Diswasher will also try to start when in off mode. Replaced circuit board and it does to same. Did I get a bad circuit board or is there another problem. Also when I try water service test, I get a Rinse aid fault.


U REPLACED THE CIRCUIT BOARD IN THE DOOR, THE ONE BEHIND THE CONTROL BUTTONS? THAT IS THE TIMER, IT IS KNOWN AS THE CCU OR CENTRAL CONTROL UNIT, THAT IS WHAT CONTROLS ALL TIMED FUNCTIONS, SO THAT REALLY IS THE ONLY PART THAT CAN CAUSE THIS PROBLEM ... Frigidaire 24 in. FDB1050REC Stainless Steel Built-in Dishwasher

Hi I have a Kudso1flSS1 dishwasher. I just replaced the control board and the switch board assembly, the pump is recently replaced and the filter is clean. The start button keeps flashing and the water level is always low. The DW stops running after 15 minutes and the flashing starts again...... Help!


... KitchenAid 24 in. KUDS01FLBL Built-in Dishwasher

I have a Bosch SHU43 dishwasher, about 6 years old. After starting a cycle, it will run for a while, perhaps 1/2 to 2/3 of the way through the cycle, then shut off. After 10-20 minutes it will start up again, run for a few minutes, then shut off again. It ends up taking about 12 hours for a cycle to finish. The problem started off somewhat intermittent and has gotten worse over the last few weeks. I've checked the electrical box in the front right bottom, and the connection is good. I've even


Hello,\015\012\015\012Welcome to FixYa.\015\012\015\012I`m not sure since you didn`t mention it or perhaps I just interpreted it this way, but is it consistent at the same time or approximately or is ... Bosch 24 in. SHU43 Built-in Dishwasher

We have a 6 year old Jenn Air dishwasher model JDB2150AWP We had a cracked door close unit which we replaced but got a short while restoring connections I am wondering if there is an internal circuit breaker, relay or fuse on these machines that we need to check and possibly replace since we cannot get it to run at all. No power or lights at all. I believe all connections are secure and we replaced the door close unit with new parts.


... Jenn-Air 24 in. JDB2150AWP Built-in Dishwasher

Bosch SHE58C05UC/50 dishwasher stopped at 96 minutes (will not advance) & I cannot cancel. Diagnostic codes C4 then P0, rinse light steady on, drying light flashing. No water in anti-overflow pan, it's dry, float switch is working. Vacuumed out any/all water, Have replaced water inlet valve. Main circuit board shows no sign of solder joint disruption. Have switched circuit on, then off in attempt to reset (negative results). Any ideas on how to reset and then to fix the problem?


... Bosch Evolution 800 SHE58C05UC Stainless Steel Built-in Dishwasher

My dishwasher was running (Model # MDB9150AWB) was running and stopped. No lights on the front at all. Checked, and it is getting power from the 110 line at the connection to the wires in the lower (stationary) panel. Any thoughts on whether there is a circuit board that needs to be replaced?


... Maytag MDB7100AWB Dishwasher

We got our maytag 300 quiet series about 3 years ago from home depot. about a year ago the option buttons/lights on the right side went dead. It was out of warranty and still worked so i ignored it. Now last night, the left side buttons/lights still work, but the start button is dead. It wont run at all. Any ideas?


Our Maytag dishwasher (an earlier model) quit too. Found that the door latch operates two micro-switches which supply power to the machine and one of the switches no longer made contact when operated. The switch pair and the plastic latch parts are s ... Maytag 24 in. MDB5651A Built-in Dishwasher

Q Electrolux dishwasher's element was replaced last year in march 2010 when it was having short circuit again and again. But now after almost a year the same problem is occurring so please advise if I get an electrician to check the lines or a technician from Electrolux to fix the dishwasher?


... Electrolux 23 in. ESL624 Built-in Dishwasher

I have water in the bottom and the LED read 2H, It's about 10 years old, last year I replaced the sensor board. Should I invest more to fix or get a new dishwasher?


Refer your user guide for the error message meaning. Take service center help if you find complicated.However you check the water inlet for free flow into the machine! ... Bosch SHU5315UC Dishwasher

I have a Kitchen Aid dishwasher that ha had the processing board replaced twice in the last year. It is not functioning again so this will be the third time in 13 months. Any reasons why the board keeps failing?


Do you live in an area that has a lot of power outages? That could be one reason. Another reason is an area that has power surges. You can have an electrician add a surge protector to your electric fuse box that will help. Otherwise, if a good techni ... KitchenAid 24 in. KUDS25 Built-in Dishwasher

I purchased my Kenmore Elite dishwasher, model # 8542514, in 2003 & replaced the control board in 2006. Recently, I accidently opened the dishwasher during a wash cycle, but it continued working once I closed it. It seemed to work fine for a few more weeks. Now, however, I get nothing--no lights....just doesn't start up. I tried pressing all the code solutions listed on this site, but no luck so far. It seems to me that the control board/panel should last more than 3-4 years.


... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

I have a Kenmore Type 575-0 Dishwasher, model number 665.16033401, Style 16033. It runs trough the cycle, once the cycle is complete the clean mode light is on but most dishes are still dirty. I had someone here to repair this about a year ago. All he did was press alternating two buttons, which I have tried, it resets and lets you start a new cycle. However, the problem remains. Last time there was only button pressing involved, no need to replace anything. So, I would hate to have to pay ag


You need an electronic control and heating element ... Dishwashers
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1613 seconds