Having problems with your Bosch Dishwashers ?

Bosch model SHX36L. The wash cycle is not ending, we have to open the door to stop it. We initially thought there was no hot water, but then realized the water was not as hot as it normally is.


Answers :

Repair Help & Product Troubleshooting for Bosch Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bosch model SHX36L. The wash cycle is not ending, we have to open the door to stop it. We initially thought there was no hot water, but then realized the water was not as hot as it normally is.


... Bosch Dishwashers

Professional series - stainless Start the cycle and it seems normal, clock ticks down but a few minutes in, it engages in the "wasH' cycle (seems to have filled some water in the tub at this point which is hot) and does nothing.... the timer just ticks away.... thoughts?


Is it please possible to provide the model number of your dishwasher.\015\012\015\012When you say water in the tub is hot, is it because the dishwasher is connected to the hot water inlet connection? Do you hear the drain pump at any time ... Frigidaire Professional Series 24 in. Built-In Dishwasher Dishwasher

Dishwasher I have a whirlpool dishwasher that does not appear to be getting hot water. The washer water is cold initially and only seems to get warm once the heater in the base of the machine heats it. The hot water supply line does not get hot so I presume no water is being supplied. Is the water supposed to be hot at the start. If yes could this be caused be a faulty inlet valve and if so how can I check. The dishes are dirty especially on the top rack. Thanks for your help. David


Gendos is on track with his question. I have the same dishwasher and it doesn't get enough hot water to clean the dishes and runs for hours because the heating element wasn't designed to heat water, just maintain it. The only solution we have found ... Whirlpool GU2400XTP Built-in Dishwasher

Kenmore Elite Stainless Steel 24 inch tall Model 66577963K701. The heating element works for "heated dry" but not for "Hi Temperature" wash. It used to do so and when I opened the door a nice blast of steam would come out. My hot water tank is a great distance from the washer so we usually run the hot water tap in the sink for a bit until hot water comes... but the heating coil no longer kicks in on any of the cycles (Smart Wash / Normal Wash ). The high limit switch works and as I said, th


... Kenmore Dishwashers

My Bosch diswasher is hanging up in the cycle (at 102 mins. in normal cycle and 38 mins in quick cycle). I hear what sounds like a one second pumping of water into the sink area, a pause, and then another one second pumping of water, on and on, but there's no progression beyond this point. One possible cause: a few weeks ago someone turned off the hot water at the heater and another person tried to run the dishwasher. The dishwasher did not function because it could not get hot water. Perhaps


Hi\015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. To start with check the water inlet valve which is located\015\012behind the lower access panel on the left or right side of the Di ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher

The washing, heated dry, and normal wash light just flash. I have unplugged and plugged it back in several time, i tried restting it by holding down the Rinse only button for 15 seconds. I pressed the high temp ater, heated dry, high temp water, heated dry buttons to try to reset. I also ran the hot water line that feeds the dishwasher until the water was hot. Nothing has helped. The machine is18 months old and therefor no longer under warranty.


Please provide the make and model number of the dishwasher.\015\012do you hear pumps running? what was the last cycle it was at when the flashing started. was there water left at the base of the dishwasher from the cycle that stopped? ... Dishwashers

Does it hurt a pressure washer to run hot water thought it went they hook up the water for outside to hook it to the hot water i did not no it and i hook it to the pressure washer


Most pressure washers have packings that can sustain a temperature of 140 degrees although it as strongly not recommended since the pump head heats up when in bypass mode(triggergun closed)best rule for pressure washer is never leave the trigger clos ... Karcher 2500 PSI Pressure Washer

Maytag dishwasher model MDB7609AWW2 has a blinking clean light. I followed the advice on fixya (thankya!) and by alternating the normal and heated wash buttons I was able to return the lights to normal. However, once I tried to run a normal cycle, it didn't do anything other than fill and drain. I then ran the hot water faucet in the sink until hot and tried another new cycle, but no luck. Any advice is MUCH appreciated!


... Dishwashers

Ken wood kdw60w10 dishwasher no hot water, there seems to be no power to the inline heating element, showing 30ohms resistance and power directly applied when removed from the dishwasher and it heats up. No fault codes on panel, works normally apart from no hot water, any other ideas? Many thanks


... Dishwashers

HDW101SS does not heat water. Heater element mearures 28 Ohms. Temp Limiter is N.C. Temp controllers TS50 & TS60 not found. On economy wash timer moves as normal then stops when red heater light should come on. If the timer is assisted one click it will progress as normal but no hot water.


Hi.If the temp limiter shows no continuity, there will be no voltage reaching the element contacts. The high limit is connected in series with the heating element. If the hi limit is open the element will not get power. Any technician wil ... Haier HDP18PA Stainless Steel Free-Standing Dishwasher

KitchenAid KUDL03IVWHO Machine seems to stop after the initial water fill. There is power to the machine, the door latch circuity is working, all the buttons on the control pad light up. After selecting any of the wash cycles and pressing start, the washing light illuminates and the machine fills normally to the point where the fill valve stops the inflow of water. At this point the machine stalls, it does not start the cleaning process. I can press cancel and the machine drains normally. I e


Hi,\015\012\015\012You have got to the correct resolution. This is a circuit or most commonly called the board problem. Please find the bellow mentioned link which will help you to get one compatible for your washer.\015\012\0 ... Dishwashers

My Miele Platnum dishwasher is not working. It is flashing "intake/drain" When it begins instead of the normal hearing of water moving around you just hear a humming. My husband and father took out all the filters/baskets etc and made sure everything was cleaned out. They checked the hoses. After that it seemed like it was going to work because it started to cycle normally but now it is flashing again and this time there was water standing in the bottom of the dishwasher. Any thoughts?


Most common faults with dishwashers is a drain fault. Check for any kinked hoses and check the drain spigot under the sink where the drain hose connects into the u bend. Usually this is where food gets trapped due to the spigot not being drille ... Miele 23 in. Novotronic G841 Built-In Dishwasher

Our Hotpoint Dishwasher BFI 680 will start up as normal on any program, take in water, heat it up then, we hear a bubbling noise, as though the hot water is just boiling and not being pumped around. Is this the pump? Thing is, the machine will then drain the water, with the pump presumably pushing the water out?


Install new pump kit ... Hotpoint 23 in. BFI68 Built-in Dishwasher

I have a Delonghi dishwasher, it's a stand alone, like a washing machine. The water inlet is connected to the hot water tap, normally used for a washing machine. When we first started using the dishwasher, we kept getting the E4 error message, we reduced the water inlet pressure by turning down the tap, that worked for a while. Just a while ago, we started getting the E4 error message again, not sure we can turn down the tap any further without cutting the water off completely. Do you have a


The E4 error message could be because the water pressure is too low rather than too high. Can you let me know the exact model number of your dishwasher and I should be able to tell you more.\015\012\015\012Regards,\015\012BElectric ... Dishwashers

Purchased in 2003. Dishes were exquisitly clean till 2008. Our water heater temp was set at 140 temp. This heater was replaced with a heater now set at 125 temp. In the past two years dishes are nowhere as clean on the the normal start setting. Should I go to the Pots and Pans start setting to get hotter water or should I turn up my water heater? All this is assuming that water is not hot enough. Does the washer heating element ever burn out?


Try turning on your water at the sink for a while on hot let it run then start the wash cycle that should help. what that will do is let the cold water run out of the pipes and therefore you will have a hot water start. ... Kenmore Dishwashers

Diswasher TYP NBKH, SERVICE 8546 892 10010 Problem: For all programs except rinse and charge 1/2 for all programs. Pre-rinse and rinse for 50 Bio, 60 and 70 OK. Downloading water to wash causes multiple knocking (on the left side dishwashers) and simultaneous blinking light (relais?). Opening doors and adding water (different amounts - from 0.5 to 2 l) brings the normal work of dishwasher back. Rinse with cold water after washing OK. Final cleaning with hot water causes knocking again. After r


... Dishwashers

My Kenmore Elite Dishwasher (665.16499300) will not fill with water on the Normal Wash. It sounds like it's going through the cycle, but there's no water. I always run the hot water through the tap first. Oddly, the machine operates just fine in the Antibacterial Wash setting. Help would be greatly appreciated.


This machine is known to have a problem with the control panel. You need to get another one and replace the bad one that is in your machine. You should be able to contact sears and see about a replacement. You might even be able to get it done for y ... Dishwashers

KitchenAid KUDP01DLBS2 dishwasher. Runs for a very long time on any cycle; time does not seem to advance. (takes 2.5 hours or more for normal cycle. "sensing soak", "water heating" lights on for a long time, even though it appears that water is not being heated. Checked incoming water temp, is hot. Did not do this when new, something has changed. Typical cycle was 1 hr 10 min. before.


Sounds like the heater inside the dishwasher is not working. The machine is trying to get the water up to a preset temperature, probably in the neighborhood of 140 degrees. That is one of the things that it is sensing.After the machine fi ... Dishwashers

I have the Siemens SL84A305UC Dishwasher. All of a sudden it stopped cleaning dishes, but everything sounds normal and it fills and drains water, and sounds like it is completing the cycle. In the past when I opened the door while it was actively washing the water would spray out aggressively. Now, when I opened it while it was supposed to be washing I see just a small amount of water coming from the bottom wash blade, and not even enough to turn the blade very far. I thought it was just a c


... Siemens 24 in. SL84A305UC Built-in Dishwasher

Water remains at bottom after dish cycle is complete . Dishes come out clean and everything seems normal except for the water that remains at the bottom of the dish washer. I realize that a small amount of water is usually there but this is too much.


Set the controls to off then power off at the mains for 30 mins and then power mains back on and run a drain program or a full wash program. If the water won’t drain away then the most likely problems are the door interlock switch is faul ... Whirlpool Dishwashers

ARISTON LSI 45/50 UK ALL COLD CYCLES ARE PERFECT ON HOT CYCLES IT GOES THROUGH ALL THE STAGES BUT NEVER ENDS THE CYCLES AND ALSO I THINK THE ELEMENT TEMPERATURE IS NOT BEING SENSED TO ALLOW HOT WASHES TO CONTINUE AND FINISH I ALREADY REPAIRED THE INITIAL FAULT WHICH WAS A RED 2 PIN CONNECTOR WITH A WHITE SOCKET GOING IN TO IT BOTH WITH 2 RED WIRES ON WHICH WAS VERY BADLY BURNED / CORRODED I REPLACED THIS WITH A 15 AMP CONNECTOR BLOCK BUT NOW I HAVE THE HOT WATER CYCLE FAULT


I tried to look up your model dishwasher ( aristion lsi 24/50uk ) by whirplool / can not find in data base / also you stated that all cold cycles work/ most d/w only use hot and there is no cold cycles . so there is always time to ... Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Can you use hot water instead of the normal cold water in the Karcher winner 11. I wish to clean the grease trap of my house.


DO NOT USE HOT WATER!!! This machine is rated for cold water, the pump head is made out of plastic, the plastic pump and electric motor are cooled by the cold water that moves through the pump. If you add hot water into the mix there is a good chance ... Karcher PSI Electric Pressure Washer

I have the Asko 1375 and it suddenly stopped washing. The water drains out fine, it gets hot and steamy but does not appear to be blasting water from the lower and upper sprayers. Thoughts how to diagnose? Or do I need a repairman? Laura Gribbin


Hi, Welcome to FixYa. Based on your description and provided the dishwasher is indeed 1) an Asko ... Asko 1375 Dishwasher

Dishwasher is making a loud grinding noise when it's started. Doesn't matter the cycle choice; the cycle starts as normal then once started up starts making a sort of grinding noise as the water is pulsing, like something is stuck or blocking the "push" of water. I couldn't see anything stuck in the bottom - any thoughts before I call a repair person? I've never owned a dishwasher before - maybe there's a basic drain/blockage thing I should check out first? And, any recommendations for repair


... Maytag 24 in. MDBH970AW Built-in Dishwasher

I have an Asko DW1875 dishwasher (10yrs old) which has just recently started having problems. The initial symptom was that during a washing cycle, unit showed '1' and inside became very hot (melting some plastic cups/plates in unit). On further investigation (with diagnostic mode), the dishwasher is filling and draining with no problem. When circulation pump runs there is barely any water pressure in blades (just dribbles out) and water leaks into undertray via a plastic white tab near front (v


... Asko D1876 Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0936 seconds