Having problems with your Bosch Dishwashers ?

GOOD AFTERNOON i HAVE A SCA24 CLASSICXX DISHWASHER THE CONTROL PANEL DISPLAY WILL TIME DOWN TO I MINUITE AND THEN STAYS AT THAT TIME WITH WHOT SOUNDS LIKE THE PUMP STILL GOING. AND ALL THE ITEMS INSIDE ARE STILL WET


Answers :

Hello,

Welcome to FixYa.

Based on your description
I'd say the issue actually is with the control...unfortunately. This is
likely within the electronic timer/control, specifically the heater relay solder joint. ( a faulty flow switch, ntc or heater can also cause this, but not very probable ).

If you feel capable of checking this on your own, there`s a way to visually inspect the control yourself...it really isn't very complicated.

It will require you to remove the control from the unit and then remove the control from it`s plastic housing and look for a burnt solder contact on the printed circuit board.


dabfa62.jpg

The culprit will 99% of the times be one of the pins from the heater relay,hence the unit sit`s and takes longer & longer to finish because it can`t heat to advance or unless the 2 buttons for "cancel" are pressed...this can also manifest as a long cycle time as I mentioned and eventually display's "1" on units with a display and usually very poor cleaning, no heating ( don't be fooled by the homes inlet hot water temperature ) as a result.

You can also run the unit through a regular or econo cycle ...any cycle with the exception of rinse & hold, and with the door panel removed place an ammeter on the gray/black wire it should draw 11 amps during the wash cycle...after it fills and the flow switch indicates it has adequate water to engage the heater.

i.e. ( this may differ from your specific model, but the same rules apply )

f57273b.jpg
**My Opinion - if you or someone you know is proficient at soldering, a lot of times it can be remedied by simply repairing the solder...but it has to be done well...or it will not last.
Bosch recommend`s replacing the control and I don`t pretend to speak on their behalf nor do I profess to know better. This is just my experience (it work`s) and my opinion (why buy new if one can repair ?)

**Please disconnect the power or turn off the breaker before attempting any service to the dishwasher.**

Thank`s for visiting "FixYa" for your repair inquiries. Please take a moment and rate this solution to it's helpfulness. Good luck.

Regards,

Macmarkus :)
Repair Help & Product Troubleshooting for Bosch Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

GOOD AFTERNOON i HAVE A SCA24 CLASSICXX DISHWASHER THE CONTROL PANEL DISPLAY WILL TIME DOWN TO I MINUITE AND THEN STAYS AT THAT TIME WITH WHOT SOUNDS LIKE THE PUMP STILL GOING. AND ALL THE ITEMS INSIDE ARE STILL WET


Hello,Welcome to ... Bosch Dishwashers

Dishwasher wont fill with water. just before it stopped filling i was turning the dial (a lot) between the wash cycles back and forth to attempt to get it to fill and drain (I didn't let it go through a cycle). We also removed the hose from the machine as it had split and replaced it and we had the machine tilted on it's side. the dial still clicks round but it sounds like the pump is going and it doesn't seem to be filling with water. Help


Hi. I suspect that the timer mechanism will be the culprit here, but i recommended to inspect and test the water inlet valve, before replacing the timer. The valve is a known problem area, as well. Follow the valve inspection procedure below, careful ... Fisher DS603W / DS603B / DS603I Dishwasher

Dishwasher will not fill with water, dishwasher sat unused for some time. it worked fine for 4 times, then it backfilled with water from the garbage disposal unit, and leaked out through the floor. When I start a cycle we hear what it sounds like a pump draining and then going to cycle without water coming in. It's a bum.


... Bosch 24 in. SMU40 Built-in Dishwasher

GE Quietpower 2 spray arms not rotating. Sounds like pump is working and water is moving inside but arms are still in same position when I check to see if they've moved. Of course the dishes don't get clean. What's up with this?


... GE 24 in. GLD5560LSS Stainless Steel Built-in Dishwasher

I have a Bosch SHU43C05UC diswasher. Last night, I put it on before going to bed as usual. I was awakened a couple of hours later to a loud grinding sound (like a pump being run dry), and found the noise coming from the dishwasher. The display read "0" time remaining, so I opened the door and the dishes seemed clean, so I left it shut off. Tonight I have been trying to troubleshoot the problem. The dishwasher will turn on, but it will not seem to fill with water. I have verified that the


Ok well before you can do anything you must obtain a service manual, link below.\015\012\015\012http://allrepairmanuals.com/bosch ... Dishwashers

Hi, Had a power cut at my home and my Caple Di455DL Dishwasher was mid cycle on a glasswash program at the time, since power has been regained it will not restart or reset itself, it just lets a pulse of four beeps go once the door is shut and makes a sounds like its trying to pump out water? tried turning off at mains etc but cant get it to reset!


... Dishwashers

The dishwasher doesn't seem to have nearly enough water in it. The upper sprayer arm doesn't seem to be spinning when running (I open the door and look really quick) and the lower one looks like it barely spins and barely sprays water. The dishes are barely wet and the soap is just laying on the bottom. The water is on, there are no kinks in the supply line. It sounds like it is running, and pumps pumping, but being brand new I am not sure what it should sound like. It certainly doesn't sound li


I would lift the drain pipe higher. approx. 1/2 the height of the dishwasher . also rechack incomming water supply. Make sure no blockages and the like. Try again. ... Bosch Dishwashers

Pump still going. Dishwasher flooded last week and pump still going every time i switch it back on. I have left off for 3 days and I have tried the reset.


Check the following:\015\012\015\012You'll need to get the water out of the bottom of the dishwasher - a wet vac usually works the best.\015\012\015\012Remove the bottom rack and check the pump inlet screen in the bottom of th ... Dishwashers

Whirlpool dishwasher doesn't seem to fill with enough water despite good water pressure. Therefore, pump sounds like it is cycling from pumping water for about 2 seconds to going dry for 2 seconds to pumping water for 2 seconds to going dry for 2 seconds, etc. Spray arms rotate only for the 2 seconds when pump is actually pumping water. Dishes do not get clean.


... Whirlpool 24 in. GU2548XTPS Built-in Dishwasher

Whirlpool ADG7540 approx 4 years old (maybe a bit older) I have ran diagnositic check and the start light flashes 4 times stops briefly then flashes 4 times again over and over along with a continuous bleeping. When I put the dishwasher on any program I can hear the pump running but after a few mins the same flashing and beeping occurs although it sounds as if the pump is still running. I have taken off the pump checked for blockages and also checked the outlet hoses and spiggot, there are non.


Yikes, we have just identified this exact same problem tonight. If you've had any success with fixing it, we would sure appreciate hearing how. Best of luck with your machine ... Whirlpool 24 in. ADG7540 Built-in Dishwasher

Dishlex DX102 How do I get access to the impeller. I have broken down and cleaned everything from inside the dishwasher, but the water still does not pump away. It pumps in water okay, but not away. How do I go further, the last two screws drop the whole unit down, do I have to pull the dishwasher out and go thru the front kick panel?


Your outlet path is most likely clogged with food, the remains of paper labels, or a combination of both (assuming the sealing plug was not left in your disposer unit). I've taken lots of these apart and they are all slightly different. Hopefully y ... Dishwashers

Kenmore elite dishwasher stopped in middle of cycle with water still inside. Checked breaker. Replace the hole control panel, door latch from a used kenmore elite. Work for half a cycle and quit with water still inside just like the first time.


Here's your solution (free PDF) - Kenmore Elite Dishwasher Manual ... Kenmore 24 in. 16352 / 16354 / 16359 Built-in Dishwasher

I am a licensed plumber who installed a frigidaire fdb1o5rem1 dishwasher for a customer about 2 years ago. It has water to the solenoid valve and the screen is clean. I can see water coming in to the unit on left side through the port hole on the inside of the unit. Dishes do not get clean and it doesnt act like water is being distrubuted inside the dishwasher. Soap never gets washed away from door. Dishwasher makes funny sound in mid cycle like the pump is not running in wash cycle. Discharge p


I can see from what you have described (by the way it is a very clear and precise description which is very helpful), there is a problem in the water circulation system. These dishwashers use an alternating water flow method to split the water circul ... Frigidaire Dishwashers

Hello, I have a Kitchen Aid (model # KUDMO1T JWHO) dishwasher that runs the motor in all cycles, with water fill & drain working fine, but the pump is not pumping water during any cycle, as the spinners and the inside of the washer are dry when I open the door, except for the water sitting in the bottom. Also, no normal swishing sound of water when the motor runs in any cycle. Looks to me like a mechanical break in the pump drive. How do I check the pump drive on this model? Do you have any


... KitchenAid Dishwashers

My Fisher and paykel Nemo dishwasher makes a funning on off sound when put on any cycle. Sound like water going through solinoid in short busts then stops , then starts again, after some time it then


... Fisher and Paykel Dishwashers

Plastic Pieces We purchased our ASKO 1385 dishwasher 7-8 years ago. Over the years, I have found "small square, thin, pieces of gray plastic" inside. Where are these coming from? Also, we have replaced the drain pump 2 years ago and looks like we'll be replaced the main pump within the next few days as no water is going through. We are looking at paying big $$$ for that pump. Almost half as much as purchasing a new dishwasher. Is this a common problem?


Yes, I have the same problem and it is the upper bearing rack, not the pump impeller. The new bearing kit is $30.00 (another is available for $123.00-the same!!). ... Asko 1385 Dishwasher

I have a Bosch integrated dishwater that is just over 2 years old. It has suddenly stopped working and the tray at the bottom is not emptying, although you can still hear a buzzing sound. The cycle does not go beyond this point. I have emptied the tray of water and the dishwasher will start again, and pump water in, but it then stops, as though it is not able to pump water out. Does anyone know what this is? Could it be the pump? A blockage?


... Bosch 24 in. SHU43 Built-in Dishwasher

Hello my beko dishwasher keeps on pumping out even when it is empty of water. i think it happened after the first rinse it pumps constently i havepoured water through it the outlet is not blocked it just keeps going its like the pump thinks there is still water to be extracted


... Beko 24 in. D3731F Free-standing Dishwasher

KitchenAid KUDMO1TJ has a humming sound and think the motor or pump is locked up. how do i check if this is the problem? The dishwasher fills, heats, and drains without ever washing/spraying the dishes. The dispenser still has soap in, the lid does open. I would like to know how to remove the pump. Please give us your expert advice.


... KitchenAid Dishwashers

My ASKO 1805 Dishwasher started to smell weird and white smoke came from it. I turned it off, but after I turned it on again it just keeps pumping water in and out, I can't get in contact with it (None of the indicator lights are working and it is not reacting to any commands) In addition the safety feauture that is supposed to stop all operation the moment the door is opened is no longer working. (i.e. even with the door open it is still pumping water) Does it sound like an expensive repair? (


Hello,\015\012\015\012Welcome to FixYa. Based on your description ( specifically the white smoke and smell ) I would suspect the control board is faulty. \015\012\015\012If the unit does not stop when the door is open can be r ... Asko 24 in. 1805 Built-in Dishwasher

Tecnik DW2677 Hi, my dishwasher regularly starts to bleep after starting a wash program. When the door is opened it stops bleeping and the right hand light flashes 7 times repeatedly in sequence. By holding down the start and program change buttons together for a few seconds, it will reset. If you then close the door all is well for a few seconds the pump sound like it expells some water and then it starts to bleep again. The above process can happen several times before it decides to do what it


Check your water intake- i had the same issue - a leaky fitting wasn't supplying enough water to the dishwasher. had exactly the same symptoms you describe. fixed the leak, reset the dishwasher & it's working fine.\015\012\015\012\015\012\0 ... Tecnik TDW2677 Built-in Dishwasher

I have a Frigidaire Dishwasher, model #FDB635rfs It is not that old, but appears to have quit working. It sounds like it runs the water gets pushed in by the tube on the side but goes straight to the bottom of the washer. It looks like the spray arms are not spinning. Water is not circulating. Element still heats up. Detergent just runs down the inside of the door and doesn't dissolve since water is not circulating through arms. I have just replaced the water inlet valve and it did not hel


Don't know about yours but many of the rotating spray-heads are turned only by waterpressure, not a separate motor.\015\012The rotator is normally pretty loose and should turn willingly by hand; if it seems stiff and your water pressure is normally l ... LG LDF6810 Built-in Dishwasher

I have a Bosch dishwasher model SHU9915 that is 8 years old. It just give a ''hum'' when it tries to go into the wash cycle. It stops humming after a few seconds, like it overheats or overloads, then after a minute or so it tries to start the motor again and ''hums''. It continues this as long as you wish to watch it. Does it sound like the pump has gone out or just a capacitor or something small?


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks for using FixYa. You are right the issue is with\015\012the motor; don’t think it’s related to a capacitor. The hum ... Bosch Dishwashers

Have a Kenmore Freestanding Dishwasher that was working when hooked up to the sink. When we plumbed it in and connected the electrical directly, we now get an "F4" flashing on the panel with a beeping noise and the pump sounds like it wants to drain but just get a sucking noise. I've tried putting water in it to prime the pump, but still doesn't want to work. Do the codes mean anything, or point to a specific part?


... Kenmore 24 in. 16332 / 16334 / 16339 Free-standing Dishwasher

KENMORE DISHWASHER Hi, My husband just received a reset "code" for our dishwasher and the light went off and we thought it was going to work. But now no water is going in, we can hear it making like a humming sound and its warm inside when we open the door. Can you guide us?


You probably have a build up of food under the bottom heating element. The excess food falls to the bottom and then clogs up the space where water collects to be heated. The heater works but there is no water to heat, so washer will go on to next pha ... Kenmore 24 in. 16019 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1617 seconds