Having problems with your Bosch Dishwashers ?

I have a Bosch Dishwasher about 10 years old, model SHV4803UC/U07. Yesterday it stopped working along with no lights on the selector buttons. I have reset the circuit breaker ( which did seem to not be off at any rate). It seem not to be getting any power if it's not the circuit breaker what else could cause this?


Answers :

Repair Help & Product Troubleshooting for Bosch Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Bosch Dishwasher about 10 years old, model SHV4803UC/U07. Yesterday it stopped working along with no lights on the selector buttons. I have reset the circuit breaker ( which did seem to not be off at any rate). It seem not to be getting any power if it's not the circuit breaker what else could cause this?


... Bosch Dishwashers

GE GSD5320 seemed to finish all light wash cycles. Then it began to beep, with the NORMAL light blinking. I hit RESET, but none of the other buttons worked. I threw the circuit breaker for this appliance and waited an hour. I Turned the circuit breaker on but now I get the NORMAL light blinking, even when the door latch is not engaged. No buttons work.


... GE GSD5320DBB Dishwasher

When trying to start the dishwasher, pressing the Normal wash button, the dishwasher gives a huge clunk and then it trips the circuit breaker. Upon resetting the breaker, I tried the next button over, which is Soak and Wash, and it seems to go thru the cycle fine. Another time I tried the Normal button, but put the left dial on Rinse and it started up, but it would clunk periodically and it seemed to have a 'hot' smell. I'm worried to use it - what could this be? Is there anything else I can try


Hi\015\012\015\012This is a very dangerous situation you must remove from the wall supply and desist from using, such a fault could easily make the casing "Live" and anyone touching it may be killed. You need to discover why this is happe ... Dishwashers

GU1500XTLS3 Periodically won't start. Dishwasher has power because pressing cancel causes dishwasher to start draining (even though there is no water). Door switch works because opening door prevents starting drain cycle. No other button on control panel will work except for the 'air dry' / 'lockout' button. Turning off circuit breaker for 15-30 minutes and then turning circuit breaker back on seems to fix the problems but only for a couple uses and then it stops working again. Need ad


This could be the 'fill switch', which is the level sensor. Could be a plastic tube that exerts air pressure into the tube as it fills, make sure it's clear and open. The dishwasher has a sensor that monitors the door being closed too. Some use a hig ... Dishwashers

No lights come on at control panel on Kitchenaid KUDS01fl. Circuit Breaker seems fine (have reset it).


... KitchenAid Dishwashers

I have a KitchenAid Whisper Quiet Dishwasher. Has been working fine. Circuit breaker seem to be working but control board is now not lighting up and buttons do not respond. Seems like no power to control board.


I may have leaked water into the mother board ciruitry. This can happen when there is a tiny leak or when steam gets in. Check with kitchenaid, that is a good product and kitchen aid will stand by thier equipment. ... KitchenAid Dishwashers

I used the dishwasher a couple of days ago and then today I could not turn it on the unit seems to have electric to it and I am thinking it might be a fuse. the circuit breaker seems ok


Check where the power comes into machine and the door switches. ... Frigidaire Dishwashers

I have a Kenmore Elite Dishwasher Model 665.13773K600. It seems to have no power to the touch pad (top) control panel. I have already checked the circuit breaker and the power to the dishwasher. A friend said that it may perhaps be the thermo fuse cut out that needs to be replaced. 1) Is this true? 2) How can I remove the 1" thick control panel touch pad after removing the six screws- it seems to be stuck, and I don't want to break the plastic touchpad.


... Kenmore Dishwashers

My dishwasher just stopped working in the middle of the wash cycle. It seems to have no power to it. I have checked all the circuit breakers and reset them all and still nothing. Any ideas?


Your hard wiring maybe bad, or a wire nut came off call electritian or someone who knows electricity ... Whirlpool 24 in. GU980SCG Built-in Dishwasher

The dishwasher stop during the wash cycle. It did finish draining the water from the tub. The machine is not showing a power signs, I check the circuit breaker and the fuse is not tripped. I open and closed the door and the door latch seems to be working fine. There is just no power to the washer. Usually when a machine breaks down, there still is power or buttons that light up on the front of the machine. I looked on the internet and many say that the fuse could be tripped. No where can I find


... Whirlpool DU912 Dishwasher

I have a GE Quiet Power 3 that has completly died. I cannot get a light to come on or anything to beep when pressing buttons. I checked the circuit breaker and outlet and they are both working fine. I tried pressing and holding the reset button on the front control panel and nothing. It seems to have just died at 2 years old. Anyone have a solution? GE wants $80 just to look at it.


A dead set simply means a cut off of power supply. Open the back cover of your dishwasher . Locate the area where the AC cord is located and look for the plastic fuse holder which is usually installed in one of the AC cord line open it and replace t ... Dishwashers

Whirlpool Quiet Partner II. Does nothing at all when you try to start it. Seems latched tightly and I double-checked and reset the circuit breaker. Thoughts?


CHECK THAT THERE IS VOLTAGE AT THE CONNECTION TO THE D/W. CHECK WALL SWITCHES, GFI OUTLETS FOR TRIPPED, THAT THE WATER TO D/W US ON. IF IT TRIPPED CIRCUIT BREAKER. MAY BE SHORTED INTERNALLY. ... Dishwashers

Wash cycle stopped with water in the bottom. Seems like there is no power. Can't get lights on cycles buttons to turn on. Power button does nothing. Checked circuit breakers. All are on. Lights and outlets around dishwasher area are working.


Check the wiring in the units junction box. Its located at the bottom right corner. You will likely find melted connectors. If so, you need to cut the wires back and replace these connectors. Make sure you turn the power off before doing any of this ... Bosch 24 in. SHX46A05UC Built-In Dishwasher

Diswhasher Quiet Partner II. Just won't do anything. Seems to be latched and I checked the circuit breaker twice. Any thoughts? James


Following is a full rundown on how to diagnose from my tips. You can also view go going to my profile. Please rate this tip if you find it helpful.\015\012\011\011\015\012\011\011\015\012\011\011\015\012\011\011\015\012\ ... Whirlpool Dishwashers

My kenmore Elite stopped working after my daughter open the door during a cycle. There seems to be no power. Circuit breaker is fine. Any thoughts? Thanks


Check the wall socket for \015\012\011\011\011power. Sometimes the power cord disconnects at the dishwasher \015\012\011\011\011(inside the junction box, behind the bottom kick panel), if this is \015\012\011\011\011the case, the wiring must be repai ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

My kenmore Elite stopped working after my daughter open the door during a cycle. There seems to be no power. Circuit breaker is fine. Any thoughts? Thanks


It appears your timer/main controller/CCU has failed in this instance.For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.I recommend both sites bec ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher

Control Panel won't let me hit the start button. The dishwasher is a little over a year old and is used at most once a week. The blue light on the bottom right of the dishwasher seems to no longer light up. The control panel will let me select the wash, but the start button and time indicator does not light up. Not sure if this a real defect and if just a simple exchange of the front control panel will fix the problem? Already tried resetting the circuit breaker and that did not help. Than


... Dacor Epicure ED24 Stainless Steel Builtin Dishwasher

Own a Frigidaire Dishwasher Model Number FDB4315LFSO and now after about 2 years suddenly the display will not light and function anything. Without pulling the power panel off the whole line circuit seems to have power as they have my disposal unit tied into same electric line and that runs and so does everything else and no breaker is tripped. Is their a reset somewhere to check or any ideas what can casue the display panel not to function any commands at all. Nick


... Dishwashers

My daughter accidentally turned on our GE GLDA690 dishwasher. I can't seem to cancel it out without actually starting the cycle. I opened the door before the cycle started but now it is sitting there beeping. The obvious thing is to load it with dishes and run it. But it is just the two of us and we don't really have a load full. Owner's manual is no help. Even turning off the circuit breaker will not stop this infernal beeping. How do I cancel it? Why isn't there a cancel button?


... GE GLDA690MWW / GLDA690MBB Built-in Dishwasher

My kitchenaid dishwasher won't start, no lights go on, it stopped in te middle of the cycle. The circuit breaker was checked and it seems fine.


... KitchenAid Dishwashers

We have a Kenmore Elite Dishwasher #665.1646 - 5yrs old. On Friday nite, there were no problems but last nite the lights would not go on when cycles were pressed ( or Start). Checked the circuit breaker and it was OK. There is nothig caught in the bottom and the overfill float is functioning. I pressed Hi-temp and Air dry alternately and all the lights lit. I pressed Smart Wash, then Start and it did not go on. I can hear it draining but no water seems to flow and then it stops. All light t


The thermal fuse on the control panel. There isa couple of wires that lead up to a white box with the fuse in it. Thatis the problem. If you are good with a volt meter or light and youplace it across the fuse, if it is bad the light will light ... Kenmore Dishwashers

Dishwasher will not run. I have checked the circuit breaker and it seems fine. does the dishwasher have a reset button?


Hello there:\015\012My dishwasher will not work at all.\015\012Investigate these four areas if your dishwasher is not working at all:\015\012\015\012 \015\012\015\012 \015\012 \015\012 \015\012\011 \015\012 \015\012\ ... KitchenAid Dishwashers

Kenmore Elite Drawer Dishwasher model 465.13329600 Normal Wash and High Temp Wash buttons stay lit, as does green Lock button. The Start/Resume button and the red button on the front of the drawer keep flashing. I've tried key combos suggested above, but nothing seems to work. Even tried shutting it off at the circuit breaker to reset it, and that didn't work either. This ****** was purchased in 2006 or 2007, and hasn't been used very much. WTF?


... Kenmore Dishwashers

The dishwasher will not turn on. The timer lights are on even when I turn off the circuit breaker it is one whrn the electricity comes back on the latch seems to be ok. how do I get to the timer.


... Whirlpool 24 in. GU2500 XTP Built-in Dishwasher

3 problems: 1. lower drawer is hard to close; seems to be sticking on something. 2. lower drawer retains water (2 inches) after completing a cycle. 3. F1 fault code on both drawers with alert occurred when washers were not in use. I had to turn off the electric circuit breaker to make it stop.


Ok where to start, first thing the bottom draw is hard to close because they use 2 little motors on either side to pull a lid with a seal on it down on top of each draw when u start it to keep the water in, if its hard to close the motors are damaged ... Fisher and Paykel 24 in. DS-603 Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.0702 seconds