Having problems with your Bosch Dishwashers ?
GE Profile dishwasher heating element will not shut off
\015 After wash cycle the heating element stays on. Even after resetting the wash control it stays on. I was only able to turn it off by shutting off the breaker. It appears to be stuck in the on position. Is there a relay/switch/temp sensor that could be malfunctioning that would cause this?\015
Sounds like the timer assembly must have stuck on the dry cycle. I'd call a tech before you have a fire.
Repair Help & Product Troubleshooting for Bosch Dishwashers
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
GE Profile dishwasher heating element will not shut off
Sounds like the timer assembly must have stuck on the dry cycle. I'd call a tech before you have a fire. ... Bosch Dishwashers
I have a GE Profile Dishwasher, Model# PDW7880J03SS that doesnt dry the dishes. I pulled out the dishwasher and checked the heating element for continuity with my ohm meter and got a closed circuit reading. I tested the voltage going to the heating element and got a 124V reading. However the dishes are still soaking wet after the drying cycle. What am i missing, what else could be wrong with the machine that the dishes won't dry at all?
Hi\015\012\015\012Check if the dishwasher is draining and filling properly is water temperature. Water temperature should be between 120 and 140 F. If water is not hot enough then heating element has gone bad, to check the element you'll ... Dishwashers
Maytag MDBH970AWS Heating element won't turn off. Dishwasher heating element won't turn off. Have to shut off the breaker to make it cool down. Heating element gets hot as soon as you flip the breaker back on
The heater relay is located on the control board, a faulty relay or a faulty control board would cause the problem you have described. The fix is to replace the control board. Parts for your unit should be available from most appliance parts retail ... Maytag 24 in. MDBH970AWS Built-in Dishwasher
My Jenn-Air Dishwasher (JDB12070AWF) the heating element won't shut off it just keeps staying hot. I unplugged it but it melted 3 cutting boards and now I am afraid to plug it back in. What do I do to fix this?
... Jenn-Air Dishwashers
Have a frigidaire dishwasher (model- PLD4375RFC0)about 2 years old. Set to run as we left to go out of town- when we came back all lights flashing including error- found a child's plastic bowl that had fallen to the bottom and had a melted spot as it was next to the heating element. Called support and were told to master restart- shut the power off for 15 minutes. Did and now flashing "27". Cannot find a code for that and neither could support without sending out a repairman. Any advice before
... Frigidaire Dishwashers
Kenmore dishwasher model 363.1410691, approximately 18 yrs old... Wash cycle was on, unlocked and opened door to add silverware, shut and locked the door, but water did not (and will not) come back on. Appears heating element and timer still works...any ideas?
Check your water valve. if know water goes in normally that is the culprit. disconnect the wires and ohms it out with a ohms it out. if this works then you can help me by sending me a 4 thumbs up post thanks! ... Kenmore Dishwashers
My GE Profile Performance dishwasher (GSD 4910) doesn't drain. I hear the pump working, and water draining into the sink (not a disposal) as it should, but water is left standing in the tub about as high as the heating element. I have taken it apart and removed a few small items stuck in the system in various places, but that didn't affect anything. I have read here and there about the piston and nut assembly, but I don't think my model has that -- or maybe it does? Can you affer a
... GE 24 in. GSD4910X Built-in Dishwasher
I have a whirlpool dishwasher DU915WKSO: when I turn the dishwasher on, the heating element comes on but no water comes into the unit. I recently replaced the garbage disposal and th dishwasher worked fine for a time or two. Since then I have only been able to get water in it once. Like I said, the heating element works but no water in the dishwasher. Thanks for any help.
... Whirlpool DU1055XTS Built-in Dishwasher
My dishwasher does not do a hot wash. Why is this? If I need to replace the heating element, how do i gain access to heating element on my Bosch classixx dishwasher?
Hi, a common problem with these machines is the solder coming away from the heater relay. A simple repair if your lucky. Run a continuity test on the element with a multimeter before replacing it, as it is a massive job to change it. I just changed m ... Bosch SHU9950 Dishwasher
Kenmore Dishwasher Model 665.15912001 Heating element doesn't seem to be heating. Wash cycles are loooooong and the drying cycle doesn't exist. Easy fix or buy a new dishwasher? I haven't tested anything yet. Should I start with the thermostat or the element itself?
Hi. i would test the element first. this will be the likely issue.First, open the doorand look into the tub and locate the heating element (if it is covered, remove the lower dish rack and cover). The heating element has two termina ... Dishwashers
Westinghouse Dishwasher Model SB907W5*08 the dishes are not getting cleaned & it appears that it is not heating as i bought a bottle of dishwasher cleaner & the dishwasher is supposed to heat up enough to dissolve the lid off the cleaner to let the fluid out. after putting the cleaner through a cycle the cleaner lid was still there. i think this must mean that the heating element is broken? this is out of warranty & can't remember how much it cost us so don't know whether better off gettin
Hi\015\012If you are observing that the dishes are not clean, then you'll need to follow certain steps to be sure where exactly the issue. First thing to check for is the detergent cup and spray arms. Check if the dishwasher's spray arms are w ... Westinghouse 24 in. MDP531 RF Free-standing Dishwasher
Dishwasher zdt 6053 Heating element not working......sometimes!!!! tried all three cicles nothing, heating element not working then its fine again for a couple of washes ????? anyone ever come across this problem, faulty thermostat ,faulty heating element,gremlin in the circuit board?????
... Zanussi 23 in. ZDT6252 Built-in Dishwasher
I have an Indesit IDL500 dishwasher. It had stopped heating the water up, it looked as if it had short circuited and so i replaced it, i have power going to the element. A couple of forums state that it may be the pcb behind the timer/selector switch. Does this pcb control the program selection and heating of the element? or is there a thermostat that controls the stop and start of the heating element? Any help would be greatly appreciated
Hi\015\012\015\012The unit\015\012has two thermostats and you can test both of them for continuity before\015\012replacing, no continuity replace the thermostat. Hope\015\012this helps...please post back fo ... Indesit 24 in. IDL500 Built-In Dishwasher
Nasty dishwasher there is nasty wet grunge at the bottom of the door, around the place the heating unit in the bottom of the dishwasher. half the time the dishes are clean in the bottom of the dishwasher. half the heating element is melted..for some reason...what do i do. the dishwasher still works, if we make sure the dishes are clean before they go in. using more for a sanitation thing than a dishwasher. can ya'll help me?
Sounds like your heating element is broken and you should replace it to prevent a possible fire hazard. \015\012You can replace the element easily for not alot of cash. You'll need to pick up a new one at an appliance parts store, just bring them the ... Kenmore 24 in. 17482 / 17484 / 17489 Built-in Dishwasher
Heating element circut malfunction In Dishwasher. Wash not workin
Great job walking through the possible causes! Hey, it is time to check the heating element itself. First visually, looking for brakes and then feeling for "bubbles" on the round element rod. Also see if it moves excessivly when you wiggle.\015\01 ... KitchenAid 24 in. KUDS01FLSS Built-In Dishwasher
I have a dishwasher model 66516979200 it doesnt dry the dishes i saw the heat sensing light on an opened it and felt the heating element and it was not hot at all ive checked the water temp at the sink and it is at 120 could the heating element be the problen or something else
... Kenmore 16602 / 16604 / 16609 Built-in Dishwasher
Smeg Dishwasher DWD 63.1 SS, not heating; I have Smeg dishwasher that is sticking in its cycle (wash phase), water was cold, so I assumed the element had failed (or tank termostat), so I have replaced both element and tank thermostat in turn. No change, water still cold and dishwasher sticks in the wash cycle. Any ideas? (Note, no diagnostic leds on this model)
The heating element stopped heating in my Maytag dishwasher, Model DWU8860BAE. I put in a new heating element, but it doesn't heat.rnWhat might be the problem? What should I do?
... Maytag Dishwashers
Bosch dishwasher shx46b02uc has stopped drying. Per online comments, they seem to point to either a corroded wire or a bad heating element. We've replaced the heating element and all the wires looks fine. All other functions work - just not the heat. Open to suggestions.
Hello,Welcome to FixYa.Based on your description ... Bosch 24 in. SHU66C02 / SHU66C06 Built-in Dishwasher
HEATING ELEMENT IT SEEMS THAT THE HEATING ELEMENT IS NOT HEATING. THIS CAUSES THE DISHWASHER TO RUN LONGER AND THE DISHES ARE NOT CLEANING PROPERLY. I WAS WONDERING HOW TO TROUBLE-SHOOT AND FIX THIS PROBLEM.
Hi\015\012\015\012follow the manual:\015\012http://www.kitchenaid.com/assets/pdfs/product/ZUSECARE/8574093.pdf\015\012\015\012if it dosent work then as you mentioned the heating unit is bad\015\012you can replace it by yourself by buying it and insal ... KitchenAid 24 in. KUDI01IL - Multiple Color Free-Standing Dishwasher
My Omega Eurolux Dishwasher (mode: DW211P/1) won't stop cycling, It sems to get stuck during the wash cycle and continues for hours, until I turn it off. If I turn the dial to rinse it rinses fine. It doesn't seem to heat the water at all, there is no steam when I open the door. I have put a new heating element in, but this doesn't seem to be heating up at all. When I open the door mid wash cycle the element is cold to touch.
Hobart AM14/1 free standing dishwasher with booster. Booster will not heat up beyond 41C. All three heating elements check ok with Ohm meter. High limit not tripped. Temperature screw up at maximum, when you turn the screw, you can hear thermostat click at lower temperature on and off. When turning on main power for dishwasher, heater in dishwasher works fine, but no relays click in the booster tank area. Have not checked for power at booster, have checked all fuses with meter and are ok. Ple
... Hobart AM14-253 Free-standing Dishwasher
Replacing heating element in Kitchenaid dishwasher KUDI01TJBL0
... KitchenAid KUDI01TBK Dishwasher
I need to replace the heating element and electronic control board on my Kitchenaid KUDS01DL Dishwasher. I have the parts. I have been able to find directions on how to replace the heating element, but am not finding anything on the electronic control board. I don't even know where this part goes. I am guessing somewhere in the door, but can't find any instructions. Help...
... KitchenAid 24 in. KUDS01DLSS Built-in Dishwasher
I need to change the heating element in my Kenmore Elite Built in Dishwasher and don't know how to get the old heating element out
Disconnect\015\012 the power source to your dishwasher before you conduct this or any \015\012other test. Either unplug the unit from the wall outlet, remove the \015\012appropriate fuse from the fuse box, or flip the appropriate breaker in \015\012t ... Kenmore Dishwashers