Having problems with your Bosch Dishwashers ?

Bosch SGI4345AU/30 shows 2h no matter what wash selection is selected


Answers :

Repair Help & Product Troubleshooting for Bosch Dishwashers

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bosch SGI4345AU/30 shows 2h no matter what wash selection is selected


... Bosch Dishwashers

Bosch SGI4345AU/17 shows 2H on the display, it does not seem to matter which program is selected, the unit runs continually. It does not heat the water or finish any cycle. The washing tablet covers the dishes and is not rinsed off. Any thoughts


The Control unit on your Bosch has a burnt out heat circuit. Just about every dishwasher has a number of "thermal holds" during the wash and rinse cycles in which the controller waits for the water to be heated to a specific temperature ... Bosch Dishwashers

Bosch SHE44C02UC digital display shows longer time for regular wash than power wash


Sadly enough, same problem. looks as though micro processor is defective. ... Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

When I press the start button, Bosch dishwasher (model SHY56A 05UC) just keep running the motor pumping the water out of dishwasher, irrespective of: 1) the wash cycle it is on, 2) whether the door is closed or open, 3) whether I cancel drain cycle, as told by Bosch Cust Svc in following steps: - "Cancel Drain" by pressing 'Quick Wash' and 'Regular Wash' buttons together for a minute until it shows 0* - Shut power off for a minute and wait for a minute - Restart on Quick Cycle. Paid


What is happenig i believe and has happened to me 2 times is that the water level float that is on the left side of dishwasher is stuck.\015\012\015\012Either remove side panel and flick lever or pull dishwasher out and tap lower portion ... Bosch SHY56A02 / SHY56A06 Built-in Dishwasher

My Candy DFI 45 DISHWASHER WILL NOT RESTART AFTER POWER CUT, THE SELECT TYPE OF WASH BUTTON IS LIT UP BUT WHEN i PUSH IT TO SELECT NO LIGHT SHOWS ON THE SELECTED WASH


It sounds like you req a new pcb assy ..it could of blew it with a power surge :( 01179512835 ... Candy DFI Plan Built-In Dishwasher

Bosch dishwasher My Bosch dishwasher finished a wash cycle and was showing the "END" light on, however, the motor was still running as though it was stuck on the drain cycle (there is a gurgling sound from where the eater drains off beneath the filter. Subsequently turning the washer on just repeats the apparent drain cycle with a constant gurgling sound (it does not kick into wash mode). The number on the manual is & 258 (7705).


Is all the water draining from the tub? if not the pressure switch will not reset and it will continue to try and clear it self...check drainage system.\015\0122. pressure switch is jammed on..build up in the sensing chamber..commo ... Bosch 24 in. SHU43 Built-in Dishwasher

Bosch Dishwasher sgs55e02au Showing tap/faucet symbol when setting to wash cycle


... Dishwashers

Amana e71195 dishwasher wont let me select normal wash and won't start no matter what I do


... Amana 24 in. ADB1500AW Built-in Dishwasher

I have a Bosch dishwasher model SHE4AP02UC/06, serial number FD901102579 that has been used twice since installation. When I select the Regular Wash cycle, the Regular Wash LED and the Active LED come on. The machine washes the dishes and then when it stops making noise. At that point the Active LED goes off and the Clean LED comes on with the Regular Wash LED. These LED's do not go off. There is no signal saying that the dishwasher is finished. Is this the way it is supposed to be operating or


Ya id say until u open the door after it has washed ... Bosch Dishwashers

Kenmore Ultra Wash model #665.1374* purchased 1/26/08 electronic control pad doesn't work properly - one wash cycle works (no matter which cycle is selected, it defaults to same one - light wash) - "washing" and "drying" cycle lights don't work -


... Kenmore Dishwashers

I have a SHU43C05UC/22 Bosch dishwasher that runs fine till it gets to wash then it seems to stick there. the timer times down to 1 and it stays there for a really long time. it doesn't appear that the washer ever gets out of the wash cycle. when you stop/open the door there is still soapy water in the tub. You can cancel the program and it will drain the tub fine then you have to select rinse and hold to clean out the soap out.


... Bosch 24 in. SHU43 Built-in Dishwasher

I have an Electrolux Dishlex DX303 Dishwasher. Recently it has been stopping early in the cycle and the display shows -10. The selected program is flashing. The cycle will restart by pressing the program button again but it no longers wash's right through the wash pe=rogram as it is meant to. I do not have the manual to trouble shoot and find out what this means. Your help would be appreciated. Regards Peter H


Hi peter,\012according to manual book -10 is not filling water fast enough.\012check inlet hose and valve, check pressure switch and pressure SW hose and clean sump filter which located bottom of tub that plastic strainer and stainless mesh clean the ... Dishwashers

I have a Bosch SHX43M05UC Dishwasher. To wash, you select the cycle and then close the door to start the wash. Now when I push the on button, the pump turns on. I can't tell if it's pumping water or not but it's not supposed to start until the door is closed.


... Bosch SHX43M05UC Built-in Dishwasher

My control pannel is showing lights I can not deselect when I choose a normal wash cycle, what could correct this problem?! When I select "Normal" the "soak and scour" and "heated dry" lights come on. I can not turn them off and I can not select anything else to change the options.


... Whirlpool DU1055XTVS Builtin Dishwasher

The original control unit from Bosch' dishwasher SHU4302UC/14 has been replaced after recall from Bosch with a new one that stop working after three washes. It does not respond to any command and shows ''0'' at display. What may be the problem?


... Bosch 24 in. SHU43 Built-in Dishwasher

Bosch 5300 d/w runs and does not complete wash cycle. I can't even cancel and drain. Display panel now shows decimal pints ie 4.3. as washing goes on. There are no clogs or kinks in line. Pump problem?


If you are unable to cancel the drain cycle then this is a problem with the control board ... Bosch 23 in. SHU5302UC Built-in Dishwasher

Bosch she45m shows 1 min. remaining at end of wash cycle


... Bosch Dishwashers

My bosch logixx dishwasher quick wash has never


I would change the control board or control module. thermador .com will let you order it. ... Bosch SHU9915UC Dishwasher

When I press the "on" button, the display shows *8, no matter which other button I select. Then when I close the door, the "dry" light comes on.


Hi\015\012\015\012 \015\012\015\012 \015\012\015\012Thanks\015\012for using FixYa. Fault code “8” = NTC (temperature\015\012sensor) fault. If NTC probe has failed ... Bosch Dishwashers

I have a Bosch SGS66E02GB/45 that no longer completes a wash cycle. On "Auto 50C" time counts down from 2:58 to about 1:40 then goes back to the beginnnig and repeats. Spray arms are moving, it fills and drains, detergent is dispensed. I have checked the inlet and outlet pipes, the impellor and non-return-valve in the sump, checked the matrix is clear, checked to anti-flood float and switch and replaced the relays on the PCB. Selecting a rinse cycle will complete. Dishes are warm and wet rather


... Bosch Dishwashers

Bosch dishwasher SGS45EO2GB/45 does not complete washing cycle. It stays at 1 min left with pump running. I have reset the machine twice at which stage the pump empties the machine and the display shows 0 mins. However, have tried it agin and same problem. Any ideas, please?


... Dishwashers

Bosch SHE43M02UC Dishwasher, display shows 1, quick wash light blinks, rinse agent light on.


... Bosch Dishwashers

Bosch SHX46A (6 years old) Selected regular cycle, pressed On and closed door. Cycle did not start normally. Pump runs, but no water is coming into the DW. I confirmed the water supply line is turned on. I opened door, turned off On/Off switch, then poured water into drain. Then turned On/Off switch on. DW began pumping water OUT of the DW. Also, it doesn't matter if the door is open or closed - if you turn the DW on, the pump will run. I suspect a problem with the electrical controls, or perha


From your description, I doubt that the problem is door latch is the cause.\015\012\015\012The first thing that a modern dishwasher does before it begins to fill with water is run the drain pump.  It appears that this DW is not progressing ... Bosch Integra® 500 SHX46A0 Dishwasher

Bosch SHU6802 dishwasher quit part way through wash. No lights showing and no response to off/on switch. Power is on at dishwasher input. Where can I find a wiring diagram?


Go to searsdirect. enter your model number and you can access a complete parts diagram and wiring diagram. http://www.searsp ... Bosch 23 in. SHU 8805 Built-in Dishwasher

I get a quick beepbeepbeep when I press the start button. As if the drawer were not completely closed but the drawer is closed. Then, nothing, the display just shows the length in minutes of the selected wash, as if it's ready to go. .


Check if the lock is not enabled. Do you see a key symbol on the display? press lock button for 4-5 secs to disable.\015\012It is possible the door close sensor is faulty. ... Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.a-wash.org || Terms of Use || Contact || Privacy Policy
Load time: 0.1337 seconds